[ Upstream commit 3f5eb062e8aa335643181c480e6c590c6cedfd22 ]
Issue a Diag-Reset when the "Doorbell-In-Use" bit is set during the
driver load/initialization.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110173341.11595-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9fba20c29e27dc99e55e1c550573a114561bf8c ]
On the Asus X541UAK an unknown event 0xCF is emited when the charger
is plugged in. This is caused by the following AML code:
If (ACPS ())
{
ACPF = One
Local0 = 0x58
If (ATKP)
{
^^^^ATKD.IANE (0xCF)
}
}
Else
{
ACPF = Zero
Local0 = 0x57
}
Notify (AC0, 0x80) // Status Change
If (ATKP)
{
^^^^ATKD.IANE (Local0)
}
Sleep (0x64)
PNOT ()
Sleep (0x0A)
NBAT (0x80)
Ignore the 0xCF event to silence the unknown event warning.
Reported-by: Pau Espin Pedrol <pespin@espeweb.net>
Closes: https://lore.kernel.org/platform-driver-x86/54d4860b-ec9c-4992-acf6-db3f90388293@espeweb.net
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241123224700.18530-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f1aa0c533d9dd8a835caf9a6824449c463ee7e2 ]
The register addresses are unsigned ints so we should use %u not %d to
log them.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20241127-regmap-test-high-addr-v1-1-74a48a9e0dc5@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c064de86d2a3909222d5996c5047f64c7a8f791b ]
Fix the hardware revision numbering for Qlogic ISP1020/1040 boards. HWMASK
suggests that the revision number only needs four bits, this is consistent
with how NetBSD does things in their ISP driver. Verified on a IPS1040B
which is seen as rev 5 not as BIT_4.
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20241113225636.2276-1-linmag7@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43439076383a7611300334d1357c0f8883f40816 ]
For the watchdog timer to work properly on the QCML04 board we need to
set PWRGD enable in the Environment Controller Configuration Registers
Special Configuration Register 1 when it is not already set, this may
be the case when the watchdog is not enabled from within the BIOS.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241025063441.3494837-1-james.hilliard1@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d8e4771f99c0400a1873235704b28bb803c83d17 upstream.
The "user" pointer was converted from being allocated with kzalloc() to
being allocated by devm_kzalloc(). Calling kfree(user) will lead to a
double free.
Fixes: 6d734f1bfc33 ("mtd: rawnand: atmel: Fix possible memory leak")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c43ec96e8d34399bd9dab2f2dc316b904892133f upstream.
The at_xdmac_memset_create_desc may return NULL, which will lead to a
null pointer dereference. For example, the len input is error, or the
atchan->free_descs_list is empty and memory is exhausted. Therefore, add
check to avoid this.
Fixes: b206d9a23ac7 ("dmaengine: xdmac: Add memset support")
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Link: https://lore.kernel.org/r/20241029082845.1185380-1-chenridong@huaweicloud.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362f1bf98a3ecb5a2a4fcbdaa9718c8403beceb2 upstream.
The for_each_child_of_node() loop requires explicit calls to
of_node_put() to decrement the child's refcount upon early exits (break,
goto, return).
Add the missing calls in the two early exits before the goto
instructions.
Cc: stable@vger.kernel.org
Fixes: f7d12ef53ddf ("dma: mv_xor: add Device Tree binding")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241011-dma_mv_xor_of_node_put-v1-1-3c2de819f463@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dc48c88fcf82b89fdebd83a906aaa64f40fb8a9 upstream.
For devm_phy_destroy(), its comment says it needs to invoke phy_destroy()
to destroy the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_consume(), and the missing
phy_destroy() call will cause that the phy fails to be destroyed.
Fortunately, the faulty API has not been used by current kernel tree.
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff764963479a ("drivers: phy: add generic PHY framework")
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-3-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0b82ab95b4f1fbc3e3aeab9d829d012669524b6 upstream.
For devm_of_phy_provider_unregister(), its comment says it needs to invoke
of_phy_provider_unregister() to unregister the phy provider, but it will
not actually invoke the function since devres_destroy() does not call
devm_phy_provider_release(), and the missing of_phy_provider_unregister()
call will cause:
- The phy provider fails to be unregistered.
- Leak both memory and the OF node refcount.
Fortunately, the faulty API has not been used by current kernel tree.
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff764963479a ("drivers: phy: add generic PHY framework")
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/stable/20241213-phy_core_fix-v6-2-40ae28f5015a%40quicinc.com
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-2-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4bfa9b6d7bd752bfe4700c937f235aa8ce997b upstream.
For devm_phy_put(), its comment says it needs to invoke phy_put() to
release the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_release(), and the missing
phy_put() call will cause:
- The phy fails to be released.
- devm_phy_put() can not fully undo what API devm_phy_get() does.
- Leak refcount of both the module and device for below typical usage:
devm_phy_get(); // or its variant
...
err = do_something();
if (err)
goto err_out;
...
err_out:
devm_phy_put(); // leak refcount here
The file(s) affected by this issue are shown below since they have such
typical usage.
drivers/pci/controller/cadence/pcie-cadence.c
drivers/net/ethernet/ti/am65-cpsw-nuss.c
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff764963479a ("drivers: phy: add generic PHY framework")
Cc: stable@vger.kernel.org
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-1-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2d633cb1421e679b56f1a9fe1f42f089706f1ed upstream.
For macro for_each_child_of_node(parent, child), refcount of @child has
been increased before entering its loop body, so normally needs to call
of_node_put(@child) before returning from the loop body to avoid refcount
leakage.
of_phy_provider_lookup() has such usage but does not call of_node_put()
before returning, so cause leakage of the OF node refcount.
Fix by simply calling of_node_put() before returning from the loop body.
The APIs affected by this issue are shown below since they indirectly
invoke problematic of_phy_provider_lookup().
phy_get()
of_phy_get()
devm_phy_get()
devm_of_phy_get()
devm_of_phy_get_by_index()
Fixes: 2a4c37016ca9 ("phy: core: Fix of_phy_provider_lookup to return PHY provider for sub node")
Cc: stable@vger.kernel.org
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-5-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ebdc6be16c2000e37fcb8b4072d442d268ad492 upstream.
_of_phy_get() will directly return when suffers of_device_is_compatible()
error, but it forgets to decrease refcount of OF node @args.np before error
return, the refcount was increased by previous of_parse_phandle_with_args()
so causes the OF node's refcount leakage.
Fix by decreasing the refcount via of_node_put() before the error return.
Fixes: b7563e2796f8 ("phy: work around 'phys' references to usb-nop-xceiv devices")
Cc: stable@vger.kernel.org
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-4-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b458e8be0d13e81ed03fffa23f8f9b528bbd786 upstream.
There may be a potential integer overflow issue in inftl_partscan().
parts[0].size is defined as "uint64_t" while mtd->erasesize and
ip->firstUnit are defined as 32-bit unsigned integer. The result of
the calculation will be limited to 32 bits without correct casting.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Zichen Xie <zichenxie0106@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2dd59fe0e19e1ab955259978082b62e5751924c7 ]
Syzbot reports [1] an uninitialized value issue found by KMSAN in
dib3000_read_reg().
Local u8 rb[2] is used in i2c_transfer() as a read buffer; in case
that call fails, the buffer may end up with some undefined values.
Since no elaborate error handling is expected in dib3000_write_reg(),
simply zero out rb buffer to mitigate the problem.
[1] Syzkaller report
dvb-usb: bulk message failed: -22 (6/0)
=====================================================
BUG: KMSAN: uninit-value in dib3000mb_attach+0x2d8/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758
dib3000mb_attach+0x2d8/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758
dibusb_dib3000mb_frontend_attach+0x155/0x2f0 drivers/media/usb/dvb-usb/dibusb-mb.c:31
dvb_usb_adapter_frontend_init+0xed/0x9a0 drivers/media/usb/dvb-usb/dvb-usb-dvb.c:290
dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:90 [inline]
dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:186 [inline]
dvb_usb_device_init+0x25a8/0x3760 drivers/media/usb/dvb-usb/dvb-usb-init.c:310
dibusb_probe+0x46/0x250 drivers/media/usb/dvb-usb/dibusb-mb.c:110
...
Local variable rb created at:
dib3000_read_reg+0x86/0x4e0 drivers/media/dvb-frontends/dib3000mb.c:54
dib3000mb_attach+0x123/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758
...
Fixes: 74340b0a8bc6 ("V4L/DVB (4457): Remove dib3000-common-module")
Reported-by: syzbot+c88fc0ebe0d5935c70da@syzkaller.appspotmail.com
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20240517155800.9881-1-n.zhandarovich@fintech.ru
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5d009e024056ded20c5bb1583146b833b23bbd5a upstream.
__of_get_dma_parent() returns OF device node @args.np, but the node's
refcount is increased twice, by both of_parse_phandle_with_args() and
of_node_get(), so causes refcount leakage for the node.
Fix by directly returning the node got by of_parse_phandle_with_args().
Fixes: f83a6e5dea6c ("of: address: Add support for the parent DMA bus")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241206-of_core_fix-v1-4-dc28ed56bec3@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7dfa7fde63dde4d2ec0083133efe2c6686c03ff upstream.
The current code uses some 'goto put;' to cancel the parsing operation
and can lead to a return code value of 0 even on error cases.
Indeed, some goto calls are done from a loop without setting the ret
value explicitly before the goto call and so the ret value can be set to
0 due to operation done in previous loop iteration. For instance match
can be set to 0 in the previous loop iteration (leading to a new
iteration) but ret can also be set to 0 it the of_property_read_u32()
call succeed. In that case if no match are found or if an error is
detected the new iteration, the return value can be wrongly 0.
Avoid those cases setting the ret value explicitly before the goto
calls.
Fixes: bd6f2fd5a1d5 ("of: Support parsing phandle argument lists through a nexus node")
Cc: stable@vger.kernel.org
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20241202165819.158681-1-herve.codina@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a16e24e34f28210f68195259456c73462518597 upstream.
When F_SEAL_FUTURE_WRITE was introduced, it was overlooked that udmabuf
must reject memfds with this flag, just like ones with F_SEAL_WRITE.
Fix it by adding F_SEAL_FUTURE_WRITE to SEALS_DENIED.
Fixes: ab3948f58ff8 ("mm/memfd: add an F_SEAL_FUTURE_WRITE seal to memfd")
Cc: stable@vger.kernel.org
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204-udmabuf-fixes-v2-2-23887289de1c@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07a756a49f4b4290b49ea46e089cbe6f79ff8d26 upstream.
If the KVP (or VSS) daemon starts before the VMBus channel's ringbuffer is
fully initialized, we can hit the panic below:
hv_utils: Registering HyperV Utility Driver
hv_vmbus: registering driver hv_utils
...
BUG: kernel NULL pointer dereference, address: 0000000000000000
CPU: 44 UID: 0 PID: 2552 Comm: hv_kvp_daemon Tainted: G E 6.11.0-rc3+ #1
RIP: 0010:hv_pkt_iter_first+0x12/0xd0
Call Trace:
...
vmbus_recvpacket
hv_kvp_onchannelcallback
vmbus_on_event
tasklet_action_common
tasklet_action
handle_softirqs
irq_exit_rcu
sysvec_hyperv_stimer0
</IRQ>
<TASK>
asm_sysvec_hyperv_stimer0
...
kvp_register_done
hvt_op_read
vfs_read
ksys_read
__x64_sys_read
This can happen because the KVP/VSS channel callback can be invoked
even before the channel is fully opened:
1) as soon as hv_kvp_init() -> hvutil_transport_init() creates
/dev/vmbus/hv_kvp, the kvp daemon can open the device file immediately and
register itself to the driver by writing a message KVP_OP_REGISTER1 to the
file (which is handled by kvp_on_msg() ->kvp_handle_handshake()) and
reading the file for the driver's response, which is handled by
hvt_op_read(), which calls hvt->on_read(), i.e. kvp_register_done().
2) the problem with kvp_register_done() is that it can cause the
channel callback to be called even before the channel is fully opened,
and when the channel callback is starting to run, util_probe()->
vmbus_open() may have not initialized the ringbuffer yet, so the
callback can hit the panic of NULL pointer dereference.
To reproduce the panic consistently, we can add a "ssleep(10)" for KVP in
__vmbus_open(), just before the first hv_ringbuffer_init(), and then we
unload and reload the driver hv_utils, and run the daemon manually within
the 10 seconds.
Fix the panic by reordering the steps in util_probe() so the char dev
entry used by the KVP or VSS daemon is not created until after
vmbus_open() has completed. This reordering prevents the race condition
from happening.
Reported-by: Dexuan Cui <decui@microsoft.com>
Fixes: e0fa3e5e7df6 ("Drivers: hv: utils: fix a race on userspace daemons registration")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20241106154247.2271-3-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20241106154247.2271-3-mhklinux@outlook.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be48c412f6ebf38849213c19547bc6d5b692b5e5 upstream.
Patch series "zram: fix backing device setup issue", v2.
This series fixes two bugs of backing device setting:
- ZRAM should reject using a zero sized (or the uninitialized ZRAM
device itself) as the backing device.
- Fix backing device leaking when removing a uninitialized ZRAM
device.
This patch (of 2):
Setting a zero sized block device as backing device is pointless, and one
can easily create a recursive loop by setting the uninitialized ZRAM
device itself as its own backing device by (zram0 is uninitialized):
echo /dev/zram0 > /sys/block/zram0/backing_dev
It's definitely a wrong config, and the module will pin itself, kernel
should refuse doing so in the first place.
By refusing to use zero sized device we avoided misuse cases including
this one above.
Link: https://lkml.kernel.org/r/20241209165717.94215-1-ryncsn@gmail.com
Link: https://lkml.kernel.org/r/20241209165717.94215-2-ryncsn@gmail.com
Fixes: 013bf95a83ec ("zram: add interface to specif backing device")
Signed-off-by: Kairui Song <kasong@tencent.com>
Reported-by: Desheng Wu <deshengwu@tencent.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff30bd6a6618e979b16977617371c0f28a95036e upstream.
On SH, devm_clk_get_optional_enabled() fails with -EINVAL if the clock
is not found. This happens because __devm_clk_get() assumes it can pass
a NULL clock pointer (as returned by clk_get_optional()) to the init()
function (clk_prepare_enable() in this case), while the SH
implementation of clk_enable() considers that an error.
Fix this by making the SH clk_enable() implementation return zero
instead, like the Common Clock Framework does.
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/b53e6b557b4240579933b3359dda335ff94ed5af.1675354849.git.geert+renesas@glider.be
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd471e25770e7e632f736b90db1e2080b2171668 ]
The values returned by the driver after processing the contents of the
Temperature Result and the Temperature Limit Registers do not correspond to
the TMP512/TMP513 specifications. A raw register value is converted to a
signed integer value by a sign extension in accordance with the algorithm
provided in the specification, but due to the off-by-one error in the sign
bit index, the result is incorrect.
According to the TMP512 and TMP513 datasheets, the Temperature Result (08h
to 0Bh) and Limit (11h to 14h) Registers are 13-bit two's complement
integer values, shifted left by 3 bits. The value is scaled by 0.0625
degrees Celsius per bit. E.g., if regval = 1 1110 0111 0000 000, the
output should be -25 degrees, but the driver will return +487 degrees.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d82 ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Link: https://lore.kernel.org/r/20241216173648.526-4-m.masimov@maxima.ru
[groeck: fixed description line length]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit de6b43798d9043a7c749a0428dbb02d5fff156e5 upstream.
Currently, the RIIC driver may run the I2C bus faster than requested,
which may cause subtle failures. E.g. Biju reported a measured bus
speed of 450 kHz instead of the expected maximum of 400 kHz on RZ/G2L.
The initial calculation of the bus period uses DIV_ROUND_UP(), to make
sure the actual bus speed never becomes faster than the requested bus
speed. However, the subsequent division-by-two steps do not use
round-up, which may lead to a too-small period, hence a too-fast and
possible out-of-spec bus speed. E.g. on RZ/Five, requesting a bus speed
of 100 resp. 400 kHz will yield too-fast target bus speeds of 100806
resp. 403226 Hz instead of 97656 resp. 390625 Hz.
Fix this by using DIV_ROUND_UP() in the subsequent divisions, too.
Tested on RZ/A1H, RZ/A2M, and RZ/Five.
Fixes: d982d66514192cdb ("i2c: riic: remove clock and frequency restrictions")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://lore.kernel.org/r/c59aea77998dfea1b4456c4b33b55ab216fcbf5e.1732284746.git.geert+renesas@glider.be
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbbd84af6ba70334335bdeba3ae536cf751c14c6 upstream.
The "gl->tot_len" variable is controlled by the user. It comes from
process_responses(). On 32bit systems, the "gl->tot_len +
sizeof(struct cpl_pass_accept_req) + sizeof(struct rss_header)" addition
could have an integer wrapping bug. Use size_add() to prevent this.
Fixes: a08943947873 ("crypto: chtls - Register chtls with net tls")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/c6bfb23c-2db2-4e1b-b8ab-ba3925c82ef5@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0cb2c504d79e7caa3abade3f466750c82ad26f01 ]
The OF node obtained by of_parse_phandle() is not freed. Call
of_node_put() to balance the refcount.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 1676aba5ef7e ("net: ethernet: bgmac: device tree phy enablement")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241214014912.2810315-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7203d10e93b6e6e1d19481ef7907de6a9133a467 ]
There is a check for NULL at the start of create_txqs() and
create_rxqs() which tess if "nic_dev->txqs" is non-NULL. The
intention is that if the device is already open and the queues
are already created then we don't create them a second time.
However, the bug is that if we have an error in the create_txqs()
then the pointer doesn't get set back to NULL. The NULL check
at the start of the function will say that it's already open when
it's not and the device can't be used.
Set ->txqs back to NULL on cleanup on error.
Fixes: c3e79baf1b03 ("net-next/hinic: Add logical Txq and Rxq")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/0cc98faf-a0ed-4565-a55b-0fa2734bc205@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b096d62ba1323391b2db98b7704e2468cf3b1588 ]
Some calls into ionic_get_module_eeprom() don't use a single
full buffer size, but instead multiple calls with an offset.
Teach our driver to use the offset correctly so we can
respond appropriately to the caller.
Fixes: 4d03e00a2140 ("ionic: Add initial ethtool support")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241212213157.12212-4-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20fd4f421cf4c21ab37a8bf31db50c69f1b49355 ]
Use memdup_user_nul() helper instead of open-coding to
simplify the code.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: ee76746387f6 ("netdevsim: prevent bad user input in nsim_dev_health_break_write()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7363f2d4c18557c99c536b70489187bb4e05c412 ]
Since commit f63b94be6942 ("i2c: pnx: Fix potential deadlock warning
from del_timer_sync() call in isr") jiffies are stored in
i2c_pnx_algo_data.timeout, but wait_timeout and wait_reset are still
using it as milliseconds. Convert jiffies back to milliseconds to wait
for the expected amount of time.
Fixes: f63b94be6942 ("i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr")
Signed-off-by: Vladimir Riabchun <ferr.lambarginio@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1134289b6b93d73721340b66c310fd985385e8fa ]
When using dma_map_sg() to map the scatterlist with iommu enabled,
the entries in the scatterlist can be mergerd into less but longer
entries in the function __finalise_sg(). So that the number of
valid mapped entries is actually smaller than ureq->num_reqs,and
there are still some invalid entries in the scatterlist with
dma_addr=0xffffffff and len=0. Writing these invalid sg entries
into the dma_desc can cause a data transmission error.
The function dma_map_sg() returns the number of valid map entries
and the return value is assigned to usb_request::num_mapped_sgs in
function usb_gadget_map_request_by_dev(). So that just write valid
mapped entries into dma_desc according to the usb_request::num_mapped_sgs,
and set the IOC bit if it's the last valid mapped entry.
This patch poses no risk to no-iommu situation, cause
ureq->num_mapped_sgs equals ureq->num_sgs while using dma_direct_map_sg()
to map the scatterlist whith iommu disabled.
Signed-off-by: Peng Hongchi <hongchi.peng@siengine.com>
Link: https://lore.kernel.org/r/20240523100315.7226-1-hongchi.peng@siengine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aca19e4037a4143273e90f1b44666b78b4dde9b ]
Some platforms (e.g. ti,j721e-usb, ti,am64-usb) require
this bit to be set to workaround a lockup issue with PHY
short suspend intervals [1]. Add a platform quirk flag
to indicate if Suspend Residency should be enabled.
[1] - https://www.ti.com/lit/er/sprz457h/sprz457h.pdf
i2409 - USB: USB2 PHY locks up due to short suspend
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240516044537.16801-2-r-gunasekaran@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 524e057b2d66b61f9b63b6db30467ab7b0bb4796 ]
The Broadcom BCM5760X NIC may be a multi-function device.
While it does not advertise an ACS capability, peer-to-peer transactions
are not possible between the individual functions. So it is ok to treat
them as fully isolated.
Add an ACS quirk for this device so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240510204228.73435-1-ajit.khaparde@broadcom.com
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7246a4520b4bf1494d7d030166a11b5226f6d508 ]
Use preserve_config in place of checking for PCI_PROBE_ONLY flag to enable
support for "linux,pci-probe-only" on a per host bridge basis.
This also obviates the use of adding PCI_REASSIGN_ALL_BUS flag if
!PCI_PROBE_ONLY, as pci_assign_unassigned_root_bus_resources() takes care
of reassigning the resources that are not already claimed.
Link: https://lore.kernel.org/r/20240508174138.3630283-5-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5afc2f763edc5daae4722ee46fea4e627d01fa90 ]
If the link is powered off during suspend, electrical noise may cause
errors that are logged via AER. If the AER interrupt is enabled and shares
an IRQ with PME, that causes a spurious wakeup during suspend.
Disable the AER interrupt during suspend to prevent this. Clear error
status before re-enabling IRQ interrupts during resume so we don't get an
interrupt for errors that occurred during the suspend/resume process.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209149
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216295
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218090
Link: https://lore.kernel.org/r/20240416043225.1462548-2-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
[bhelgaas: drop pci_ancestor_pr3_present() etc, commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9244fb55f37356f75c739c57323d9422d7aa0f8 upstream.
When removing a netfront device directly after a suspend/resume cycle
it might happen that the queues have not been setup again, causing a
crash during the attempt to stop the queues another time.
Fix that by checking the queues are existing before trying to stop
them.
This is XSA-465 / CVE-2024-53240.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: d50b7914fae0 ("xen-netfront: Fix NULL sring after live migration")
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d08932bb6e38 which is
commit 2f4574dd6dd19eb3e8ab0415a3ae960d04be3a65 upstream.
It is reported to cause build errors in m68k, so revert it.
Link: https://lore.kernel.org/r/68b0559e-47e8-4756-b3de-67d59242756e@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ross Burton <ross.burton@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ef1db3d1d2bf which is
commit 0309f714a0908e947af1c902cf6a330cb593e75e upstream.
It is reported to cause build errors in m68k, so revert it.
Link: https://lore.kernel.org/r/68b0559e-47e8-4756-b3de-67d59242756e@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ross Burton <ross.burton@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c53d96a4481f42a1635b96d2c1acbb0a126bfd54 ]
This bug was first introduced in c27f3d011b08, where the author of the
patch probably meant to do DeleteMutex instead of ReleaseMutex. The
mutex leak was noticed later on and fixed in e4dfe108371, but the bogus
MutexRelease line was never removed, so do it now.
Link: https://github.com/acpica/acpica/pull/982
Fixes: c27f3d011b08 ("ACPICA: Fix race in generic_serial_bus (I2C) and GPIO op_region parameter handling")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Link: https://patch.msgid.link/20241122082954.658356-1-d-tatianin@yandex-team.ru
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98712844589e06d9aa305b5077169942139fd75c ]
Similar to bonding driver, add NETIF_F_GSO_ENCAP_ALL to TEAM_VLAN_FEATURES
in order to support slave devices which propagate NETIF_F_GSO_UDP_TUNNEL &
NETIF_F_GSO_UDP_TUNNEL_CSUM as vlan_features.
Fixes: 3625920b62c3 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-5-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77b11c8bf3a228d1c63464534c2dcc8d9c8bf7ff ]
Drivers like mlx5 expose NIC's vlan_features such as
NETIF_F_GSO_UDP_TUNNEL & NETIF_F_GSO_UDP_TUNNEL_CSUM which are
later not propagated when the underlying devices are bonded and
a vlan device created on top of the bond.
Right now, the more cumbersome workaround for this is to create
the vlan on top of the mlx5 and then enslave the vlan devices
to a bond.
To fix this, add NETIF_F_GSO_ENCAP_ALL to BOND_VLAN_FEATURES
such that bond_compute_features() can probe and propagate the
vlan_features from the slave devices up to the vlan device.
Given the following bond:
# ethtool -i enp2s0f{0,1}np{0,1}
driver: mlx5_core
[...]
# ethtool -k enp2s0f0np0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k enp2s0f1np1 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k bond0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Before:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: off [requested on]
tx-udp_tnl-csum-segmentation: off [requested on]
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
After:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Various users have run into this reporting performance issues when
configuring Cilium in vxlan tunneling mode and having the combination
of bond & vlan for the core devices connecting the Kubernetes cluster
to the outside world.
Fixes: a9b3ace44c7d ("bonding: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-3-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecb8fed408b6454606bbb3cd0edb083bf0ad162a ]
Virtual netdevs should use NETIF_F_GSO_SOFTWARE to forward GSO skbs
as-is and let the final drivers deal with them when supported.
Also remove NETIF_F_GSO_UDP_L4 from bonding and team drivers as it's
now included in the "software" list.
Suggested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 77b11c8bf3a2 ("bonding: Fix feature propagation of NETIF_F_GSO_ENCAP_ALL")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit becc6399ce3b724cffe9ccb7ef0bff440bb1b62b ]
The module parameter qcaspi_pluggable controls if QCA7000 signature
should be checked at driver probe (current default) or not. Unfortunately
this could fail in case the chip is temporary in reset, which isn't under
total control by the Linux host. So disable this check per default
in order to avoid unexpected probe failures.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dba406fac06b009873fe7a28231b9b7e4288b09 ]
Storing the maximum clock speed in module parameter qcaspi_clkspeed
has the unintended side effect that the first probed instance
defines the value for all other instances. Fix this issue by storing
it in max_speed_hz of the relevant SPI device.
This fix keeps the priority of the speed parameter (module parameter,
device tree property, driver default). Btw this uses the opportunity
to get the rid of the unused member clkspeed.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 356983f569c1f5991661fc0050aa263792f50616 ]
t4_set_vf_mac_acl() uses pf to set mac addr, but t4vf_get_vf_mac_acl()
uses port number to get mac addr, this leads to error when an attempt
to set MAC address on VF's of PF2 and PF3.
This patch fixes the issue by using port number to set mac address.
Fixes: e0cdac65ba26 ("cxgb4vf: configure ports accessible by the VF")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241206062014.49414-1-anumula@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7899ca9f3bd2b008e9a7c41f2a9f1986052d7e96 ]
In acpi_decode_space() addr->info.mem.caching is checked on main level
for any resource type but addr->info.mem is part of union and thus
valid only if the resource type is memory range.
Move the check inside the preceeding switch/case to only execute it
when the union is of correct type.
Fixes: fcb29bbcd540 ("ACPI: Add prefetch decoding to the address space parser")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20241202100614.20731-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 265e98f72bac6c41a4492d3e30a8e5fd22fe0779 ]
Fix an issue detected by syzbot with KASAN:
BUG: KASAN: vmalloc-out-of-bounds in cmd_to_func drivers/acpi/nfit/
core.c:416 [inline]
BUG: KASAN: vmalloc-out-of-bounds in acpi_nfit_ctl+0x20e8/0x24a0
drivers/acpi/nfit/core.c:459
The issue occurs in cmd_to_func when the call_pkg->nd_reserved2
array is accessed without verifying that call_pkg points to a buffer
that is appropriately sized as a struct nd_cmd_pkg. This can lead
to out-of-bounds access and undefined behavior if the buffer does not
have sufficient space.
To address this, a check was added in acpi_nfit_ctl() to ensure that
buf is not NULL and that buf_len is less than sizeof(*call_pkg)
before accessing it. This ensures safe access to the members of
call_pkg, including the nd_reserved2 array.
Reported-by: syzbot+7534f060ebda6b8b51b3@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7534f060ebda6b8b51b3
Tested-by: syzbot+7534f060ebda6b8b51b3@syzkaller.appspotmail.com
Fixes: ebe9f6f19d80 ("acpi/nfit: Fix bus command validation")
Signed-off-by: Suraj Sonawane <surajsonawane0215@gmail.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://patch.msgid.link/20241118162609.29063-1-surajsonawane0215@gmail.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4cfbca86f6a8b801f3254e0e3c8f2b1d2d64be2b upstream.
Considering that in some extreme cases,
when u_serial driver is accessed by multiple threads,
Thread A is executing the open operation and calling the gs_open,
Thread B is executing the disconnect operation and calling the
gserial_disconnect function,The port->port_usb pointer will be set to NULL.
E.g.
Thread A Thread B
gs_open() gadget_unbind_driver()
gs_start_io() composite_disconnect()
gs_start_rx() gserial_disconnect()
... ...
spin_unlock(&port->port_lock)
status = usb_ep_queue() spin_lock(&port->port_lock)
spin_lock(&port->port_lock) port->port_usb = NULL
gs_free_requests(port->port_usb->in) spin_unlock(&port->port_lock)
Crash
This causes thread A to access a null pointer (port->port_usb is null)
when calling the gs_free_requests function, causing a crash.
If port_usb is NULL, the release request will be skipped as it
will be done by gserial_disconnect.
So add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port_usb.
Call trace:
gs_start_io+0x164/0x25c
gs_open+0x108/0x13c
tty_open+0x314/0x638
chrdev_open+0x1b8/0x258
do_dentry_open+0x2c4/0x700
vfs_open+0x2c/0x3c
path_openat+0xa64/0xc60
do_filp_open+0xb8/0x164
do_sys_openat2+0x84/0xf0
__arm64_sys_openat+0x70/0x9c
invoke_syscall+0x58/0x114
el0_svc_common+0x80/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x38/0x68
Fixes: c1dca562be8a ("usb gadget: split out serial core")
Cc: stable@vger.kernel.org
Suggested-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Acked-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/TYUPR06MB62178DC3473F9E1A537DCD02D2362@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97264eaaba0122a5b7e8ddd7bf4ff3ac57c2b170 upstream.
If the clocks priv->iclk and priv->fclk were not enabled in ehci_hcd_sh_probe,
they should not be disabled in any path.
Conversely, if they was enabled in ehci_hcd_sh_probe, they must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 63c845522263 ("usb: ehci-hcd: Add support for SuperH EHCI.")
Cc: stable@vger.kernel.org # ff30bd6a6618: sh: clk: Fix clk_enable() to return 0 on NULL clk
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241121114700.2100520-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8d3e4a734599c7d0f6735f8db8a812e503395dd upstream.
On Rasperry Pis without onboard USB hub the power cycle during
power connect init only disable the port but never enabled it again:
usb usb1-port1: attempt power cycle
The port relevant part in dwc2_hcd_hub_control() is skipped in case
port_connect_status = 0 under the assumption the core is or will be soon
in device mode. But this assumption is wrong, because after ClearPortFeature
USB_PORT_FEAT_POWER the port_connect_status will also be 0 and
SetPortFeature (incl. USB_PORT_FEAT_POWER) will be a no-op.
Fix the behavior of dwc2_hcd_hub_control() by replacing the
port_connect_status check with dwc2_is_device_mode().
Link: https://github.com/raspberrypi/linux/issues/6247
Fixes: 7359d482eb4d ("staging: HCD files for the DWC2 driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 676fe1f6f74db988191dab5df3bf256908177072 upstream.
The OF node reference obtained by of_parse_phandle_with_args() is not
released on early return. Add a of_node_put() call before returning.
Fixes: 8996b89d6bc9 ("ata: add platform driver for Calxeda AHCI controller")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d2ada05227881f3d0722ca2364e3f7a860a301f upstream.
If the current USB request was aborted, the spi thread would not respond
to any further requests. This is because the "curr_urb" pointer would
not become NULL, so no further requests would be taken off the queue.
The solution here is to set the "urb_done" flag, as this will cause the
correct handling of the URB. Also clear interrupts that should only be
expected if an URB is in progress.
Fixes: 2d53139f3162 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20241124221430.1106080-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* This function is meant for cleaning up going from STA to AP mode
* On latest 18.1 builds deleting/deactivating AP interface causes
hotspot not to work, hostapd starts up and system says hotspot
is on, but due to a kernel error (vif type isn't set to AP anymore)
SSID isn't actually broadcasted and clients can't find nor connect
to the hotspot
* So let's remove this as removing it doesn't seem to have any
negative consequences but fixes hotspot, also disable an
ugly warning caused by this which isn't actually a problem
Change-Id: I5a656fd38697b9be09ecdc5f344bc343458aeaaf
When a binder reference is cleaned up, any freeze work queued in the
associated process should also be removed. Otherwise, the reference is
freed while its ref->freeze.work is still queued in proc->work leading
to a use-after-free issue as shown by the following KASAN report:
==================================================================
BUG: KASAN: slab-use-after-free in binder_release_work+0x398/0x3d0
Read of size 8 at addr ffff31600ee91488 by task kworker/5:1/211
CPU: 5 UID: 0 PID: 211 Comm: kworker/5:1 Not tainted 6.11.0-rc7-00382-gfc6c92196396 #22
Hardware name: linux,dummy-virt (DT)
Workqueue: events binder_deferred_func
Call trace:
binder_release_work+0x398/0x3d0
binder_deferred_func+0xb60/0x109c
process_one_work+0x51c/0xbd4
worker_thread+0x608/0xee8
Allocated by task 703:
__kmalloc_cache_noprof+0x130/0x280
binder_thread_write+0xdb4/0x42a0
binder_ioctl+0x18f0/0x25ac
__arm64_sys_ioctl+0x124/0x190
invoke_syscall+0x6c/0x254
Freed by task 211:
kfree+0xc4/0x230
binder_deferred_func+0xae8/0x109c
process_one_work+0x51c/0xbd4
worker_thread+0x608/0xee8
==================================================================
This commit fixes the issue by ensuring any queued freeze work is removed
when cleaning up a binder reference.
Fixes: d579b04a52a1 ("binder: frozen notification")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Bug: 366003708
Link: https://lore.kernel.org/all/20240924184401.76043-4-cmllamas@google.com/
Change-Id: Icc40e7dd6157981f4adbea7243e55be118552321
[cmllamas: drop BINDER_STAT_FREEZE as it's not supported here]
Signed-off-by: Carlos Llamas <cmllamas@google.com>
If a freeze notification is cleared with BC_CLEAR_FREEZE_NOTIFICATION
before calling binder_freeze_notification_done(), then it is detached
from its reference (e.g. ref->freeze) but the work remains queued in
proc->delivered_freeze. This leads to a memory leak when the process
exits as any pending entries in proc->delivered_freeze are not freed:
unreferenced object 0xffff38e8cfa36180 (size 64):
comm "binder-util", pid 655, jiffies 4294936641
hex dump (first 32 bytes):
b8 e9 9e c8 e8 38 ff ff b8 e9 9e c8 e8 38 ff ff .....8.......8..
0b 00 00 00 00 00 00 00 3c 1f 4b 00 00 00 00 00 ........<.K.....
backtrace (crc 95983b32):
[<000000000d0582cf>] kmemleak_alloc+0x34/0x40
[<000000009c99a513>] __kmalloc_cache_noprof+0x208/0x280
[<00000000313b1704>] binder_thread_write+0xdec/0x439c
[<000000000cbd33bb>] binder_ioctl+0x1b68/0x22cc
[<000000002bbedeeb>] __arm64_sys_ioctl+0x124/0x190
[<00000000b439adee>] invoke_syscall+0x6c/0x254
[<00000000173558fc>] el0_svc_common.constprop.0+0xac/0x230
[<0000000084f72311>] do_el0_svc+0x40/0x58
[<000000008b872457>] el0_svc+0x38/0x78
[<00000000ee778653>] el0t_64_sync_handler+0x120/0x12c
[<00000000a8ec61bf>] el0t_64_sync+0x190/0x194
This patch fixes the leak by ensuring that any pending entries in
proc->delivered_freeze are freed during binder_deferred_release().
Fixes: d579b04a52a1 ("binder: frozen notification")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20240926233632.821189-8-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: 366003708
(cherry picked from commit 1db76ec2b4b206ff943e292a0b55e68ff3443598
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git
char-misc-next)
Change-Id: Iafdec3421c521b4b591b94455deba7ee5102c8ca
[cmllamas: drop BINDER_STAT_FREEZE and use binder_proc_ext_entry()]
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Add the pending proc->delivered_freeze work to the debugfs output. This
information was omitted in the original implementation of the freeze
notification and can be valuable for debugging issues.
Fixes: d579b04a52a1 ("binder: frozen notification")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20240926233632.821189-9-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: 366003708
(cherry picked from commit cb2aeb2ec25884133110ffe5a67ff3cf7dee5ceb
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git
char-misc-next)
Change-Id: Ifc9a22b52e38c35af661732486fa1f154adb34de
[cmllamas: fix KMI break with binder_proc_ext_entry()]
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Allow these tasks to be preempted in order to reduce latency.
Signed-off-by: Tyler Nijmeh <tylernij@gmail.com>
Signed-off-by: Forenche <prahul2003@gmail.com>
Signed-off-by: John Vincent <git@tensevntysevn.cf>
Signed-off-by: ThunderStorms21th <pinakastorm@gmail.com>
By default, everything is set to 240fps for optimal playback performance However, the situation is not always true, as it applies to cases when the video bitrate isn't necessarily high, causing high power consumption
Reduce and limit the boosting needed. For decoder, only apply for UHD
video resolution
Signed-off-by: Diep Quynh <remilia.1505@gmail.com>
[TenSeventy7: Negative unsigned integer fixes already present on 9610]
Signed-off-by: John Vincent <git@tensevntysevn.cf>
Signed-off-by: ThunderStorms21th <pinakastorm@gmail.com>
commit 38b5133ad607ecdcc8d24906d1ac9cc8df41acd5 upstream.
Static checkers complained about an off by one read overflow in
otx2_get_fecparam() and we applied two conflicting fixes for it.
Correct: b0aae0bde26f ("octeontx2: Fix condition.")
Wrong: 93efb0c65683 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Revert the incorrect fix.
Fixes: 93efb0c65683 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0aae0bde26f276401640e05e81a8a0ce3d8f70e upstream.
Fixes: 93efb0c656837 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dd075fe8ebbc6fcbf998f81a75b8c4b159a6195 upstream.
Per UVC 1.1+ specification 3.7.2, units and terminals must have a non-zero
unique ID.
```
Each Unit and Terminal within the video function is assigned a unique
identification number, the Unit ID (UID) or Terminal ID (TID), contained in
the bUnitID or bTerminalID field of the descriptor. The value 0x00 is
reserved for undefined ID,
```
So, deny allocating an entity with ID 0 or an ID that belongs to a unit
that is already added to the list of entities.
This also prevents some syzkaller reproducers from triggering warnings due
to a chain of entities referring to themselves. In one particular case, an
Output Unit is connected to an Input Unit, both with the same ID of 1. But
when looking up for the source ID of the Output Unit, that same entity is
found instead of the input entity, which leads to such warnings.
In another case, a backward chain was considered finished as the source ID
was 0. Later on, that entity was found, but its pads were not valid.
Here is a sample stack trace for one of those cases.
[ 20.650953] usb 1-1: new high-speed USB device number 2 using dummy_hcd
[ 20.830206] usb 1-1: Using ep0 maxpacket: 8
[ 20.833501] usb 1-1: config 0 descriptor??
[ 21.038518] usb 1-1: string descriptor 0 read error: -71
[ 21.038893] usb 1-1: Found UVC 0.00 device <unnamed> (2833:0201)
[ 21.039299] uvcvideo 1-1:0.0: Entity type for entity Output 1 was not initialized!
[ 21.041583] uvcvideo 1-1:0.0: Entity type for entity Input 1 was not initialized!
[ 21.042218] ------------[ cut here ]------------
[ 21.042536] WARNING: CPU: 0 PID: 9 at drivers/media/mc/mc-entity.c:1147 media_create_pad_link+0x2c4/0x2e0
[ 21.043195] Modules linked in:
[ 21.043535] CPU: 0 UID: 0 PID: 9 Comm: kworker/0:1 Not tainted 6.11.0-rc7-00030-g3480e43aeccf #444
[ 21.044101] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
[ 21.044639] Workqueue: usb_hub_wq hub_event
[ 21.045100] RIP: 0010:media_create_pad_link+0x2c4/0x2e0
[ 21.045508] Code: fe e8 20 01 00 00 b8 f4 ff ff ff 48 83 c4 30 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc 0f 0b eb e9 0f 0b eb 0a 0f 0b eb 06 <0f> 0b eb 02 0f 0b b8 ea ff ff ff eb d4 66 2e 0f 1f 84 00 00 00 00
[ 21.046801] RSP: 0018:ffffc9000004b318 EFLAGS: 00010246
[ 21.047227] RAX: ffff888004e5d458 RBX: 0000000000000000 RCX: ffffffff818fccf1
[ 21.047719] RDX: 000000000000007b RSI: 0000000000000000 RDI: ffff888004313290
[ 21.048241] RBP: ffff888004313290 R08: 0001ffffffffffff R09: 0000000000000000
[ 21.048701] R10: 0000000000000013 R11: 0001888004313290 R12: 0000000000000003
[ 21.049138] R13: ffff888004313080 R14: ffff888004313080 R15: 0000000000000000
[ 21.049648] FS: 0000000000000000(0000) GS:ffff88803ec00000(0000) knlGS:0000000000000000
[ 21.050271] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 21.050688] CR2: 0000592cc27635b0 CR3: 000000000431c000 CR4: 0000000000750ef0
[ 21.051136] PKRU: 55555554
[ 21.051331] Call Trace:
[ 21.051480] <TASK>
[ 21.051611] ? __warn+0xc4/0x210
[ 21.051861] ? media_create_pad_link+0x2c4/0x2e0
[ 21.052252] ? report_bug+0x11b/0x1a0
[ 21.052540] ? trace_hardirqs_on+0x31/0x40
[ 21.052901] ? handle_bug+0x3d/0x70
[ 21.053197] ? exc_invalid_op+0x1a/0x50
[ 21.053511] ? asm_exc_invalid_op+0x1a/0x20
[ 21.053924] ? media_create_pad_link+0x91/0x2e0
[ 21.054364] ? media_create_pad_link+0x2c4/0x2e0
[ 21.054834] ? media_create_pad_link+0x91/0x2e0
[ 21.055131] ? _raw_spin_unlock+0x1e/0x40
[ 21.055441] ? __v4l2_device_register_subdev+0x202/0x210
[ 21.055837] uvc_mc_register_entities+0x358/0x400
[ 21.056144] uvc_register_chains+0x1fd/0x290
[ 21.056413] uvc_probe+0x380e/0x3dc0
[ 21.056676] ? __lock_acquire+0x5aa/0x26e0
[ 21.056946] ? find_held_lock+0x33/0xa0
[ 21.057196] ? kernfs_activate+0x70/0x80
[ 21.057533] ? usb_match_dynamic_id+0x1b/0x70
[ 21.057811] ? find_held_lock+0x33/0xa0
[ 21.058047] ? usb_match_dynamic_id+0x55/0x70
[ 21.058330] ? lock_release+0x124/0x260
[ 21.058657] ? usb_match_one_id_intf+0xa2/0x100
[ 21.058997] usb_probe_interface+0x1ba/0x330
[ 21.059399] really_probe+0x1ba/0x4c0
[ 21.059662] __driver_probe_device+0xb2/0x180
[ 21.059944] driver_probe_device+0x5a/0x100
[ 21.060170] __device_attach_driver+0xe9/0x160
[ 21.060427] ? __pfx___device_attach_driver+0x10/0x10
[ 21.060872] bus_for_each_drv+0xa9/0x100
[ 21.061312] __device_attach+0xed/0x190
[ 21.061812] device_initial_probe+0xe/0x20
[ 21.062229] bus_probe_device+0x4d/0xd0
[ 21.062590] device_add+0x308/0x590
[ 21.062912] usb_set_configuration+0x7b6/0xaf0
[ 21.063403] usb_generic_driver_probe+0x36/0x80
[ 21.063714] usb_probe_device+0x7b/0x130
[ 21.063936] really_probe+0x1ba/0x4c0
[ 21.064111] __driver_probe_device+0xb2/0x180
[ 21.064577] driver_probe_device+0x5a/0x100
[ 21.065019] __device_attach_driver+0xe9/0x160
[ 21.065403] ? __pfx___device_attach_driver+0x10/0x10
[ 21.065820] bus_for_each_drv+0xa9/0x100
[ 21.066094] __device_attach+0xed/0x190
[ 21.066535] device_initial_probe+0xe/0x20
[ 21.066992] bus_probe_device+0x4d/0xd0
[ 21.067250] device_add+0x308/0x590
[ 21.067501] usb_new_device+0x347/0x610
[ 21.067817] hub_event+0x156b/0x1e30
[ 21.068060] ? process_scheduled_works+0x48b/0xaf0
[ 21.068337] process_scheduled_works+0x5a3/0xaf0
[ 21.068668] worker_thread+0x3cf/0x560
[ 21.068932] ? kthread+0x109/0x1b0
[ 21.069133] kthread+0x197/0x1b0
[ 21.069343] ? __pfx_worker_thread+0x10/0x10
[ 21.069598] ? __pfx_kthread+0x10/0x10
[ 21.069908] ret_from_fork+0x32/0x40
[ 21.070169] ? __pfx_kthread+0x10/0x10
[ 21.070424] ret_from_fork_asm+0x1a/0x30
[ 21.070737] </TASK>
Cc: stable@vger.kernel.org
Reported-by: syzbot+0584f746fde3d52b4675@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=0584f746fde3d52b4675
Reported-by: syzbot+dd320d114deb3f5bb79b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=dd320d114deb3f5bb79b
Fixes: a3fbc2e6bb05 ("media: mc-entity.c: use WARN_ON, validate link pads")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240913180601.1400596-2-cascardo@igalia.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[ ribalda: The context around the changes differs from master. This
version is also missing the gpio unit, so that part is gone from the
patch. ]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7d6840bed0c2b16ac3071b74b5fcf08fc488241 upstream.
The MODE SELECT(6) command allows handling mode page buffers that are up to
255 bytes, including the 4 byte header needed in front of the page
buffer. For requests larger than this limit, automatically use the MODE
SELECT(10) command.
In both cases, since scsi_mode_select() adds the mode select page header,
checks on the buffer length value must include this header size to avoid
overflows of the command CDB allocation length field.
While at it, use put_unaligned_be16() for setting the header block
descriptor length and CDB allocation length when using MODE SELECT(10).
[mkp: fix MODE SENSE vs. MODE SELECT confusion]
Link: https://lore.kernel.org/r/20210820070255.682775-3-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c749301ebee82eb5e97dec14b6ab31a4aabe37a6 upstream.
For devices that explicitly asked for MODE SENSE(10) use, make sure that
scsi_mode_sense() is called with a buffer of at least 8 bytes so that the
sense header fits.
Link: https://lore.kernel.org/r/20210820070255.682775-4-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64f093c4d99d797b68b407a9d8767aadc3e3ea7a upstream.
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits masked from the CPU address space used for the
mapping. For a PCI mapping of <size> bytes starting from <pci_addr>,
the number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1].
However, rockchip_pcie_prog_ep_ob_atu() calculates num_pass_bits only
using the size of the mapping, resulting in an incorrect number of mask
bits depending on the value of the PCI address to map.
Fix this by introducing the helper function
rockchip_pcie_ep_ob_atu_num_bits() to correctly calculate the number of
mask bits to use to program the address translation unit. The number of
mask bits is calculated depending on both the PCI address and size of
the mapping, and clamped between 8 and 20 using the macros
ROCKCHIP_PCIE_AT_MIN_NUM_BITS and ROCKCHIP_PCIE_AT_MAX_NUM_BITS. As
defined in the Rockchip RK3399 TRM V1.3 Part2, Sections 17.5.5.1.1 and
17.6.8.2.1, this clamping is necessary because:
1) The lower 8 bits of the PCI address to be mapped by the outbound
region are ignored. So a minimum of 8 address bits are needed and
imply that the PCI address must be aligned to 256.
2) The outbound memory regions are 1MB in size. So while we can specify
up to 63-bits for the PCI address (num_bits filed uses bits 0 to 5 of
the outbound address region 0 register), we must limit the number of
valid address bits to 20 to match the memory window maximum size (1
<< 20 = 1MB).
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/r/20241017015849.190271-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17f5f18085acb5e9d8d13d84a4e12bb3aff2bd64.
The origin mainline patch fix a buffer overflow issue in
amdgpu_debugfs_gprwave_read(), but it has not been introduced in kernel
6.1 and older kernels. This patch add a check in a wrong function in the
same file.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b0ddf19cca2a352b2a7e01d99d3ba949a99c84c upstream.
BIOS images may fail to load and null checks are added before they are
used.
This fixes 6 NULL_RETURNS issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Keerthana K <keerthana.kalyanasundaram@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9044ad57b60b0556d42b6f8aa218a68865e810a4 upstream.
Don't flush all pending DbC data requests when an endpoint halts.
An endpoint may halt and xHC DbC triggers a STALL error event if there's
an issue with a bulk data transfer. The transfer should restart once xHC
DbC receives a ClearFeature(ENDPOINT_HALT) request from the host.
Once xHC DbC restarts it will start from the TRB pointed to by dequeue
field in the endpoint context, which might be the same TRB we got the
STALL event for. Turn the TRB to a no-op in this case to make sure xHC
DbC doesn't reuse and tries to retransmit this same TRB after we already
handled it, and gave its corresponding data request back.
Other STALL events might be completely bogus.
Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events
if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted
endpoints even without any active bulk transfers.
Assume STALL event is spurious if it reports 0 bytes transferred, and
the endpoint stopped on the STALLED TRB.
Don't give back the data request corresponding to the TRB in this case.
The halted status is per endpoint. Track it with a per endpoint flag
instead of the driver invented DbC wide DS_STALLED state.
DbC remains in DbC-Configured state even if endpoints halt. There is no
Stalled state in the DbC Port state Machine (xhci section 7.6.6)
Reported-by: Łukasz Bartosik <ukaszb@chromium.org>
Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7738a7ab9d12c5371ed97114ee2132d4512e9fd5 ]
Add a quirk similar to eeprom_93xx46 to add an extra clock cycle before
reading data from the EEPROM.
The 93Cx6 family of EEPROMs output a "dummy 0 bit" between the writing
of the op-code/address from the host to the EEPROM and the reading of
the actual data from the EEPROM.
More info can be found on page 6 of the AT93C46 datasheet (linked below).
Similar notes are found in other 93xx6 datasheets.
In summary the read operation for a 93Cx6 EEPROM is:
Write to EEPROM: 110[A5-A0] (9 bits)
Read from EEPROM: 0[D15-D0] (17 bits)
Where:
110 is the start bit and READ OpCode
[A5-A0] is the address to read from
0 is a "dummy bit" preceding the actual data
[D15-D0] is the actual data.
Looking at the READ timing diagrams in the 93Cx6 datasheets the dummy
bit should be clocked out on the last address bit clock cycle meaning it
should be discarded naturally.
However, depending on the hardware configuration sometimes this dummy
bit is not discarded. This is the case with Exar PCI UARTs which require
an extra clock cycle between sending the address and reading the data.
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-5193-SEEPROM-AT93C46D-Datasheet.pdf
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/0f23973efefccd2544705a0480b4ad4c2353e407.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548f48b66c0c5d4b9795a55f304b7298cde2a025 ]
As per USBSTS register description about UEI:
When completion of a USB transaction results in an error condition, this
bit is set by the Host/Device Controller. This bit is set along with the
USBINT bit, if the TD on which the error interrupt occurred also had its
interrupt on complete (IOC) bit set.
UI is set only when IOC set. Add checking UEI to fix miss call
isr_tr_complete_handler() when IOC have not set and transfer error happen.
Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa46a3736afcb7b0793766d22479b8b99fc1b322 ]
Wangxun FF5xxx NICs are similar to SFxxx, RP1000 and RP2000 NICs. They may
be multi-function devices, but they do not advertise an ACS capability.
But the hardware does isolate FF5xxx functions as though it had an ACS
capability and PCI_ACS_RR and PCI_ACS_CR were set in the ACS Control
register, i.e., all peer-to-peer traffic is directed upstream instead of
being routed internally.
Add ACS quirk for FF5xxx NICs in pci_quirk_wangxun_nic_acs() so the
functions can be in independent IOMMU groups.
Link: https://lore.kernel.org/r/E16053DB2B80E9A5+20241115024604.30493-1-mengyuanlou@net-swift.com
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fa046449a82a7d0f6d9721dd83e348816038444 ]
The "bus" and "cxl_bus" reset methods reset a device by asserting Secondary
Bus Reset on the bridge leading to the device. These only work if the
device is the only device below the bridge.
Add a sysfs 'reset_subordinate' attribute on bridges that can assert
Secondary Bus Reset regardless of how many devices are below the bridge.
This resets all the devices below a bridge in a single command, including
the locking and config space save/restore that reset methods normally do.
This may be the only way to reset devices that don't support other reset
methods (ACPI, FLR, PM reset, etc).
Link: https://lore.kernel.org/r/20241025222755.3756162-1-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: commit log, add capable(CAP_SYS_ADMIN) check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b61352101470f8b68c98af674e187cfaa7c43504 ]
When nd_dax is NULL, nd_pfn is consequently NULL as well. Nevertheless,
it is inadvisable to perform pointer arithmetic or address-taking on a
NULL pointer.
Introduce the nd_dax_devinit() function to enhance the code's logic and
improve its readability.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://patch.msgid.link/20241108085526.527957-1-yiyang13@huawei.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b120edb37dc9dd8ca82893d386922eb6b16f860 ]
Most drives rewind the tape when the device is reset. Reading and writing
are not allowed until something is done to make the tape position match the
user's expectation (e.g., rewind the tape). Add MTIOCGET and MTLOAD to
operations allowed after reset. MTIOCGET is modified to not touch the tape
if pos_unknown is non-zero. The tape location is known after MTLOAD.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219419#c14
Link: https://lore.kernel.org/r/20241106095723.63254-3-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bb2d6179d1a8039236237e1e94cfbda3be1ed9e ]
Struct mtget field mt_blkno -1 means it is unknown. Don't add anything to
it.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219419#c14
Link: https://lore.kernel.org/r/20241106095723.63254-2-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e64285ff41bb7a934bd815bd38f31119be62ac37 ]
Since '1 << rocker_port->pport' may be undefined for port >= 32,
cast the left operand to 'unsigned long long' like it's done in
'rocker_port_set_enable()' above. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20241114151946.519047-1-dmantipov@yandex.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 857282b819cbaa0675aaab1e7542e2c0579f52d7 ]
This patch fixes a NULL pointer dereference bug in brcmfmac that occurs
when a high 'sd_sgentry_align' value applies (e.g. 512) and a lot of queued SKBs
are sent from the pkt queue.
The problem is the number of entries in the pre-allocated sgtable, it is
nents = max(rxglom_size, txglom_size) + max(rxglom_size, txglom_size) >> 4 + 1.
Given the default [rt]xglom_size=32 it's actually 35 which is too small.
Worst case, the pkt queue can end up with 64 SKBs. This occurs when a new SKB
is added for each original SKB if tailroom isn't enough to hold tail_pad.
At least one sg entry is needed for each SKB. So, eventually the "skb_queue_walk loop"
in brcmf_sdiod_sglist_rw may run out of sg entries. This makes sg_next return
NULL and this causes the oops.
The patch sets nents to max(rxglom_size, txglom_size) * 2 to be able handle
the worst-case.
Btw. this requires only 64-35=29 * 16 (or 20 if CONFIG_NEED_SG_DMA_LENGTH) = 464
additional bytes of memory.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241107132903.13513-1-nvbolhuis@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fa4f049dc0d9741b16c96bcbf0108c85368a2b9 ]
This patch fixes incorrect code alignment.
./drivers/net/wireless/intel/ipw2x00/libipw_rx.c:871:2-3: code aligned with following code on line 882.
./drivers/net/wireless/intel/ipw2x00/libipw_rx.c:886:2-3: code aligned with following code on line 900.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=11381
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241101060725.54640-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afe260df55ac280cd56306248cb6d8a6b0db095c ]
Under sriov, host driver will save and restore vf pci cfg space during
reset. And during device init, under sriov, pci_restore_state happens after
fullaccess released, and it can have race condition with mmio protection
enable from host side leading to missing interrupts.
So skip amdgpu_device_cache_pci_state for sriov.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Acked-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3ced9bb90b0a287a1fa6184d16b0f104a78fa90 ]
Arcadyan made routers with this PCI ID containing an AR2417.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930180716.139894-3-rosenp@gmail.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da0474012402d4729b98799d71a54c35dc5c5de3 ]
This is in two devices made by Gigaset, SX762 and SX763.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240930180716.139894-2-rosenp@gmail.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fe45fada261e1e83fce2a07fa22835aec1cf0a ]
The correct format string for resource_size_t is %pa which
acts on the address of the variable to be formatted [1].
[1] https://elixir.bootlin.com/linux/v6.11.3/source/Documentation/core-api/printk-formats.rst#L229
Introduced by commit 9d9326d3bc0e ("phy: Change mii_bus id field to a string")
Flagged by gcc-14 as:
drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c: In function 'fs_mii_bitbang_init':
drivers/net/ethernet/freescale/fs_enet/mii-bitbang.c:126:46: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Wformat=]
126 | snprintf(bus->id, MII_BUS_ID_SIZE, "%x", res.start);
| ~^ ~~~~~~~~~
| | |
| | resource_size_t {aka long long unsigned int}
| unsigned int
| %llx
No functional change intended.
Compile tested only.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/netdev/711d7f6d-b785-7560-f4dc-c6aad2cce99@linux-m68k.org/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241014-net-pa-fmt-v1-2-dcc9afb8858b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020bfdc4ed94be472138c891bde4d14241cf00fd ]
The correct format string for resource_size_t is %pa which
acts on the address of the variable to be formatted [1].
[1] https://elixir.bootlin.com/linux/v6.11.3/source/Documentation/core-api/printk-formats.rst#L229
Introduced by commit 9d9326d3bc0e ("phy: Change mii_bus id field to a string")
Flagged by gcc-14 as:
drivers/net/ethernet/freescale/fec_mpc52xx_phy.c: In function 'mpc52xx_fec_mdio_probe':
drivers/net/ethernet/freescale/fec_mpc52xx_phy.c:97:46: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Wformat=]
97 | snprintf(bus->id, MII_BUS_ID_SIZE, "%x", res.start);
| ~^ ~~~~~~~~~
| | |
| | resource_size_t {aka long long unsigned int}
| unsigned int
| %llx
No functional change intended.
Compile tested only.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/netdev/711d7f6d-b785-7560-f4dc-c6aad2cce99@linux-m68k.org/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/20241014-net-pa-fmt-v1-1-dcc9afb8858b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87e26448dbda4523b73a894d96f0f788506d3795 ]
Vendor drivers r8125/r8126 indicate that this quirk isn't needed
any longer for RTL8126A. Mimic this in r8169.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/d1317187-aa81-4a69-b831-678436e4de62@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1e2da6a5072f8abe5b0feaa91a5bcd9dc544a04 ]
It is possible, although unlikely, that an integer overflow will occur
when the result of radeon_get_ib_value() is shifted to the left.
Avoid it by casting one of the operands to larger data type (u64).
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Signed-off-by: Igor Artemiev <Igor.A.Artemiev@mcst.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a16b5cdae26207ff4c22834559384ad3d7bc970 ]
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240902113320.903147-4-liaochen4@huawei.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 361ebf5ef843b0aa1704c72eb26b91cf76c3c5b7 ]
Add quirk orientation for AYA NEO 2. The name appears without spaces in
DMI strings. That made it difficult to reuse the 2021 match. Also the
display is larger in resolution.
Tested by the JELOS team that has been patching their own kernel for a
while now and confirmed by users in the AYA NEO and ChimeraOS discord
servers.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2b35545b77a9fd8c9699b751ca282226dcecb1dd.1726492131.git.tjakobi@math.uni-bielefeld.de
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 014eccc9da7bfc76a3107fceea37dd60f1d63630 ]
The HVS can change AXI request mode based on how full the COB
FIFOs are.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.
With HVS channel 2 now being used for live video, change the
panic mode for all channels to be explicitly set by the driver,
and the same for all channels.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240621152055.4180873-7-dave.stevenson@raspberrypi.com
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61a830bc0ea69a05d8a4534f825c6aa618263649 ]
Add Dexatek Technology Ltd USB Video Grabber 1d19:6108 to the cx231xx
driver. This device is sold under the name "BAUHN DVD Maker (DK8723)" by
ALDI in Australia.
This device is similar to 1d19:6109, which is already included in cx231xx.
Both video and audio capture function correctly after installing the
patched cx231xx driver.
Patch Changelog
v1:
- Initial submission.
v2:
- Fix SoB + Improve subject.
v3:
- Rephrase message to not exceed 75 characters per line.
- Removed reference to external GitHub URL.
Signed-off-by: Rohan Barar <rohan.barar@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 229e6ee43d2a160a1592b83aad620d6027084aad upstream.
Null pointer dereference occurs due to a race between smmu
driver probe and client driver probe, when of_dma_configure()
for client is called after the iommu_device_register() for smmu driver
probe has executed but before the driver_bound() for smmu driver
has been called.
Following is how the race occurs:
T1:Smmu device probe T2: Client device probe
really_probe()
arm_smmu_device_probe()
iommu_device_register()
really_probe()
platform_dma_configure()
of_dma_configure()
of_dma_configure_id()
of_iommu_configure()
iommu_probe_device()
iommu_init_device()
arm_smmu_probe_device()
arm_smmu_get_by_fwnode()
driver_find_device_by_fwnode()
driver_find_device()
next_device()
klist_next()
/* null ptr
assigned to smmu */
/* null ptr dereference
while smmu->streamid_mask */
driver_bound()
klist_add_tail()
When this null smmu pointer is dereferenced later in
arm_smmu_probe_device, the device crashes.
Fix this by deferring the probe of the client device
until the smmu device has bound to the arm smmu driver.
Fixes: 021bb8420d44 ("iommu/arm-smmu: Wire up generic configuration support")
Cc: stable@vger.kernel.org
Co-developed-by: Prakash Gupta <quic_guptap@quicinc.com>
Signed-off-by: Prakash Gupta <quic_guptap@quicinc.com>
Signed-off-by: Pratyush Brahma <quic_pbrahma@quicinc.com>
Link: https://lore.kernel.org/r/20241004090428.2035-1-quic_pbrahma@quicinc.com
[will: Add comment]
Signed-off-by: Will Deacon <will@kernel.org>
[rm: backport for context conflict prior to 6.8]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87a0d90fcd31c0f36da0332428c9e1a1e0f97432 upstream.
Disabling card detect from the host's ->shutdown_pre() callback turned out
to not be the complete solution. More precisely, beyond the point when the
mmc_bus->shutdown() has been called, to gracefully power off the card, we
need to prevent card detect. Otherwise the mmc_rescan work may poll for the
card with a CMD13, to see if it's still alive, which then will fail and
hang as the card has already been powered off.
To fix this problem, let's disable mmc_rescan prior to power off the card
during shutdown.
Reported-by: Anthony Pighin <anthony.pighin@nokia.com>
Fixes: 66c915d09b94 ("mmc: core: Disable card detect during shutdown")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Closes: https://lore.kernel.org/all/BN0PR08MB695133000AF116F04C3A9FFE83212@BN0PR08MB6951.namprd08.prod.outlook.com/
Tested-by: Anthony Pighin <anthony.pighin@nokia.com>
Message-ID: <20241125122446.18684-1-ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f0fa47ceebcff0e3591bb7e32a71a2cd7846149 upstream.
The Vexia Edu Atla 10 tablet distributed to schools in the Spanish
Andalucía region has no ACPI fwnode associated with the SDHCI controller
for its microsd-slot and thus has no ACPI GPIO resource info.
This causes the following error to be logged and the slot to not work:
[ 10.572113] sdhci-pci 0000:00:12.0: failed to setup card detect gpio
Add a DMI quirk table for providing gpiod_lookup_tables with manually
provided CD GPIO info and use this DMI table to provide the CD GPIO info
on this tablet. This fixes the microsd-slot not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Message-ID: <20241118210049.311079-1-hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3061e170381af96d1e66799d34264e6414d428a7 upstream.
At the end of __regmap_init(), if dev is not NULL, regmap_attach_dev()
is called, which adds a devres reference to the regmap, to be able to
retrieve a dev's regmap by name using dev_get_regmap().
When calling regmap_exit, the opposite does not happen, and the
reference is kept until the dev is detached.
Add a regmap_detach_dev() function and call it in regmap_exit() to make
sure that the devres reference is not kept.
Cc: stable@vger.kernel.org
Fixes: 72b39f6f2b5a ("regmap: Implement dev_get_regmap()")
Signed-off-by: Cosmin Tanislav <demonsingur@gmail.com>
Rule: add
Link: https://lore.kernel.org/stable/20241128130554.362486-1-demonsingur%40gmail.com
Link: https://patch.msgid.link/20241128131625.363835-1-demonsingur@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78ac1c3558810486d90aa533b0039aa70487a3da upstream.
The function silently assumed that signaling was already enabled for the
dma_fence_array. This meant that without enabling signaling first we would
never see forward progress.
Fix that by falling back to testing each individual fence when signaling
isn't enabled yet.
v2: add the comment suggested by Boris why this is done this way
v3: fix the underflow pointed out by Tvrtko
v4: atomic_read_acquire() as suggested by Tvrtko
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Chia-I Wu <olvaffe@gmail.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Closes: https://gitlab.freedesktop.org/mesa/mesa/-/issues/12094
Cc: <stable@vger.kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241112121925.18464-1-christian.koenig@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2e382ae12a63560fca35050498e19e760adf8c0 upstream.
Commit 028ddcac477b ("bcache: Remove unnecessary NULL point check in
node allocations") leads a NULL pointer deference in cache_set_flush().
1721 if (!IS_ERR_OR_NULL(c->root))
1722 list_add(&c->root->list, &c->btree_cache);
>From the above code in cache_set_flush(), if previous registration code
fails before allocating c->root, it is possible c->root is NULL as what
it is initialized. __bch_btree_node_alloc() never returns NULL but
c->root is possible to be NULL at above line 1721.
This patch replaces IS_ERR() by IS_ERR_OR_NULL() to fix this.
Fixes: 028ddcac477b ("bcache: Remove unnecessary NULL point check in node allocations")
Signed-off-by: Liequan Che <cheliequan@inspur.com>
Cc: stable@vger.kernel.org
Cc: Zheng Wang <zyytlz.wz@163.com>
Reviewed-by: Mingzhe Zou <mingzhe.zou@easystack.cn>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20241202115638.28957-1-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 833c70e212fc40d3e98da941796f4c7bcaecdf58 upstream.
Firmware supports multiple sg_cnt for request and response for CT
commands, so remove the redundant check. A check is there where sg_cnt
for request and response should be same. This is not required as driver
and FW have code to handle multiple and different sg_cnt on request and
response.
Cc: stable@vger.kernel.org
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07c903db0a2ff84b68efa1a74a4de353ea591eb0 upstream.
System crash is observed with stack trace warning of use after
free. There are 2 signals to tell dpc_thread to terminate (UNLOADING
flag and kthread_stop).
On setting the UNLOADING flag when dpc_thread happens to run at the time
and sees the flag, this causes dpc_thread to exit and clean up
itself. When kthread_stop is called for final cleanup, this causes use
after free.
Remove UNLOADING signal to terminate dpc_thread. Use the kthread_stop
as the main signal to exit dpc_thread.
[596663.812935] kernel BUG at mm/slub.c:294!
[596663.812950] invalid opcode: 0000 [#1] SMP PTI
[596663.812957] CPU: 13 PID: 1475935 Comm: rmmod Kdump: loaded Tainted: G IOE --------- - - 4.18.0-240.el8.x86_64 #1
[596663.812960] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 08/20/2012
[596663.812974] RIP: 0010:__slab_free+0x17d/0x360
...
[596663.813008] Call Trace:
[596663.813022] ? __dentry_kill+0x121/0x170
[596663.813030] ? _cond_resched+0x15/0x30
[596663.813034] ? _cond_resched+0x15/0x30
[596663.813039] ? wait_for_completion+0x35/0x190
[596663.813048] ? try_to_wake_up+0x63/0x540
[596663.813055] free_task+0x5a/0x60
[596663.813061] kthread_stop+0xf3/0x100
[596663.813103] qla2x00_remove_one+0x284/0x440 [qla2xxx]
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4e268f898c8a08f0a1188677e15eadbc06e98f6 upstream.
The fc_function_template for vports was missing the
.show_host_supported_speeds. The base port had the same.
Add .show_host_supported_speeds to the vport template as well.
Cc: stable@vger.kernel.org
Fixes: 2c3dfe3f6ad8 ("[SCSI] qla2xxx: add support for NPIV")
Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4812b7796c144f63a1094f79a5eb8fbdad8d7ebc upstream.
NVMe controller fails to send connect command due to failure to locate
hw context buffer for NVMe queue 0 (blk_mq_hw_ctx, hctx_idx=0). The
cause of the issue is NPIV host did not initialize the vha->irq_offset
field. This field is given to blk-mq (blk_mq_pci_map_queues) to help
locate the beginning of IO Queues which in turn help locate NVMe queue
0.
Initialize this field to allow NVMe to work properly with NPIV host.
kernel: nvme nvme5: Connect command failed, errno: -18
kernel: nvme nvme5: qid 0: secure concatenation is not supported
kernel: nvme nvme5: NVME-FC{5}: create_assoc failed, assoc_id 2e9100 ret 401
kernel: nvme nvme5: NVME-FC{5}: reset: Reconnect attempt failed (401)
kernel: nvme nvme5: NVME-FC{5}: Reconnect attempt in 2 seconds
Cc: stable@vger.kernel.org
Fixes: f0783d43dde4 ("scsi: qla2xxx: Use correct number of vectors for online CPUs")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20241115130313.46826-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4962ee045d8f06638714d801ab0fb72f89c16690 upstream.
Currently "timeout-sec" Device Tree property is being silently ignored:
even though watchdog_init_timeout() is being used, the driver always passes
"heartbeat" == DEFAULT_HEARTBEAT == 60 as argument.
Fix this by setting struct watchdog_device::timeout to DEFAULT_HEARTBEAT
and passing real module parameter value to watchdog_init_timeout() (which
may now be 0 if not specified).
Cc: stable@vger.kernel.org
Fixes: 2d63908bdbfb ("watchdog: Add K3 RTI watchdog support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241107203830.1068456-1-alexander.sverdlin@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 984836621aad98802d92c4a3047114cf518074c8 ]
If we remove the module which will call mpc52xx_spi_remove
it will free 'ms' through spi_unregister_controller.
while the work ms->work will be used. The sequence of operations
that may lead to a UAF bug.
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in mpc52xx_spi_remove.
Fixes: ca632f556697 ("spi: reorganize drivers")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://patch.msgid.link/1f16f8ae0e50ca9adb1dc849bf2ac65a40c9ceb9.1732783000.git.xiaopei01@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 851bd21cdb55e727ab29280bc9f6b678164f802a ]
If the DTS contains 'assigned-address', a dynamic address leak occurs
during hotjoin events.
Assume a device have assigned-address 0xb.
- Device issue Hotjoin
- Call i3c_master_do_daa()
- Call driver xxx_do_daa()
- Call i3c_master_get_free_addr() to get dynamic address 0x9
- i3c_master_add_i3c_dev_locked(0x9)
- expected_dyn_addr = newdev->boardinfo->init_dyn_addr (0xb);
- i3c_master_reattach_i3c_dev(newdev(0xb), old_dyn_addr(0x9));
- if (dev->info.dyn_addr != old_dyn_addr &&
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 0xb != 0x9 -> TRUE
(!dev->boardinfo ||
^^^^^^^^^^^^^^^ -> FALSE
dev->info.dyn_addr != dev->boardinfo->init_dyn_addr)) {
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
0xb != 0xb -> FALSE
...
i3c_bus_set_addr_slot_status(&master->bus, old_dyn_addr,
I3C_ADDR_SLOT_FREE);
^^^
This will be skipped. So old_dyn_addr never free
}
- i3c_master_get_free_addr() will return increased sequence number.
Remove dev->info.dyn_addr != dev->boardinfo->init_dyn_addr condition check.
dev->info.dyn_addr should be checked before calling this function because
i3c_master_setnewda_locked() has already been called and the target device
has already accepted dyn_addr. It is too late to check if dyn_addr is free
in i3c_master_reattach_i3c_dev().
Add check to ensure expected_dyn_addr is free before
i3c_master_setnewda_locked().
Fixes: cc3a392d69b6 ("i3c: master: fix for SETDASA and DAA process")
Cc: stable@kernel.org
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-3-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f552fa280590e61bd3dbe66a7b54b99caa642a4 ]
Extend the address status bit to 4 and introduce the
I3C_ADDR_SLOT_EXT_DESIRED macro to indicate that a device prefers a
specific address. This is generally set by the 'assigned-address' in the
device tree source (dts) file.
┌────┬─────────────┬───┬─────────┬───┐
│S/Sr│ 7'h7E RnW=0 │ACK│ ENTDAA │ T ├────┐
└────┴─────────────┴───┴─────────┴───┘ │
┌─────────────────────────────────────────┘
│ ┌──┬─────────────┬───┬─────────────────┬────────────────┬───┬─────────┐
└─►│Sr│7'h7E RnW=1 │ACK│48bit UID BCR DCR│Assign 7bit Addr│PAR│ ACK/NACK│
└──┴─────────────┴───┴─────────────────┴────────────────┴───┴─────────┘
Some master controllers (such as HCI) need to prepare the entire above
transaction before sending it out to the I3C bus. This means that a 7-bit
dynamic address needs to be allocated before knowing the target device's
UID information.
However, some I3C targets may request specific addresses (called as
"init_dyn_addr"), which is typically specified by the DT-'s
assigned-address property. Lower addresses having higher IBI priority. If
it is available, i3c_bus_get_free_addr() preferably return a free address
that is not in the list of desired addresses (called as "init_dyn_addr").
This allows the device with the "init_dyn_addr" to switch to its
"init_dyn_addr" when it hot-joins the I3C bus. Otherwise, if the
"init_dyn_addr" is already in use by another I3C device, the target device
will not be able to switch to its desired address.
If the previous step fails, fallback returning one of the remaining
unassigned address, regardless of its state in the desired list.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-2-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 851bd21cdb55 ("i3c: master: Fix dynamic address leak when 'assigned-address' is present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16aed0a6520ba01b7d22c32e193fc1ec674f92d4 ]
Replace the hardcoded value 2, which indicates 2 bits for I3C address
status, with the predefined macro I3C_ADDR_SLOT_STATUS_BITS.
Improve maintainability and extensibility of the code.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-1-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 851bd21cdb55 ("i3c: master: Fix dynamic address leak when 'assigned-address' is present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f18f98110f2b179792cb70d85cba697320a3790f ]
The address slot bitmap is an array of unsigned long's which are the
same size as an int on 32-bit platforms but not 64-bit. Loading the
bitmap into an int could result in the incorrect status being returned
for a slot and slots being reported as the wrong status.
Fixes: 3a379bbcea0a ("i3c: Add core I3C infrastructure")
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210922165600.179394-1-quic_jiles@quicinc.com
Stable-dep-of: 851bd21cdb55 ("i3c: master: Fix dynamic address leak when 'assigned-address' is present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 050b23d081da0f29474de043e9538c1f7a351b3b ]
devm_kasprintf() can return a NULL pointer on failure,but this
returned value in grgpio_probe is not checked.
Add NULL check in grgpio_probe, to handle kernel NULL
pointer dereference error.
Cc: stable@vger.kernel.org
Fixes: 7eb6ce2f2723 ("gpio: Convert to using %pOF instead of full_name")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20241114091822.78199-1-hanchunchao@inspur.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d036ae41cebdfae92666024163c109b8fef516fa ]
Instead of dereferencing the platform device pointer repeatedly, just
store its address in a helper variable.
Link: https://lore.kernel.org/r/20241015131832.44678-3-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 050b23d081da ("gpio: grgpio: Add NULL check in grgpio_probe")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0566f83d206c7a864abcd741fe39d6e0ae5eef29 ]
The pci_register_driver() can fail and when this happened, the dca_notifier
needs to be unregistered, otherwise the dca_notifier can be called when
igb fails to install, resulting to invalid memory access.
Fixes: bbd98fe48a43 ("igb: Fix DCA errors and do not use context index for 82576")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a0ea70da56ee8c2716d0b79e9959d3c47efab62 ]
Commit 43645ce03e00 ("qed: Populate nvm image attribute shadow.")
added support for populating flash image attributes, notably
"num_images". However, some cards were not able to return this
information. In such cases, the driver would return EINVAL, causing the
driver to exit.
Add check to return EOPNOTSUPP instead of EINVAL when the card is not
able to return these information. The caller function already handles
EOPNOTSUPP without error.
Fixes: 43645ce03e00 ("qed: Populate nvm image attribute shadow.")
Co-developed-by: Florian Forestier <florian@forestier.re>
Signed-off-by: Florian Forestier <florian@forestier.re>
Signed-off-by: Louis Leseur <louis.leseur@gmail.com>
Link: https://patch.msgid.link/20241128083633.26431-1-louis.leseur@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98337d7c87577ded71114f6976edb70a163e27bc ]
ptp_clock_adjtime sets ptp->dialed_frequency even when adjfine
callback returns an error. This causes subsequent reads to return
an incorrect value.
Fix this by adding error check before ptp->dialed_frequency is set.
Fixes: 39a8cbd9ca05 ("ptp: remember the adjusted frequency")
Signed-off-by: Ajay Kaher <ajay.kaher@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://patch.msgid.link/20241125105954.1509971-1-ajay.kaher@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 595a81988a6fe06eb5849e972c8b9cb21c4e0d54 ]
The sun4i_can_err() function only incremented the receive error counter
and never the transmit error counter, even if the STA_ERR_DIR flag
reported that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
STA_ERR_DIR flag.
Fixes: 0738eff14d81 ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-11-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee6bf3677ae03569d833795064e17f605c2163c7 ]
Call the function can_change_state() if the allocation of the skb
fails, as it handles the cf parameter when it is null.
Additionally, this ensures that the statistics related to state error
counters (i. e. warning, passive, and bus-off) are updated.
Fixes: 0738eff14d81 ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1495a21e0b8aad92132dfcf9c6fffc1bde9d5b2 ]
Clear the IRQ enable bit of WDT_MODE before asserting software reset
in order to make TOPRGU issue a system reset signal instead of an IRQ.
Fixes: a44a45536f7b ("watchdog: Add driver for Mediatek watchdog")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241106104738.195968-2-y.oudjana@protonmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daa814d784ac034c62ab3fb0ef83daeafef527e2 ]
Commit da23b6faa8bf ("watchdog: iTCO: Add support for Cannon Lake
PCH iTCO") does not mask NMI_NOW bit during TCO1_CNT register's
value comparison for update_no_reboot_bit() call causing following
failure:
...
iTCO_vendor_support: vendor-support=0
iTCO_wdt iTCO_wdt: unable to reset NO_REBOOT flag, device
disabled by hardware/BIOS
...
and this can lead to unexpected NMIs later during regular
crashkernel's workflow because of watchdog probe call failures.
This change masks NMI_NOW bit for TCO1_CNT register values to
avoid unexpected NMI_NOW bit inversions.
Fixes: da23b6faa8bf ("watchdog: iTCO: Add support for Cannon Lake PCH iTCO")
Signed-off-by: Oleksandr Ocheretnyi <oocheret@cisco.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20240913191403.2560805-1-oocheret@cisco.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4f8dbadef085ab447a01a8d4806a3f629fea05ed upstream.
The shader L1 cache is a writeback cache for shader loads/stores
and thus must be flushed before any BOs backing the shader buffers
are potentially freed.
Cc: stable@vger.kernel.org
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e9ec8d8692a6f64d81ef67d4fb6255af6be684b upstream.
K2G forwards the error triggered by a link-down state (e.g., no connected
endpoint device) on the system bus for PCI configuration transactions;
these errors are reported as an SError at system level, which is fatal and
hangs the system.
So, apply fix similar to how it was done in the DesignWare Core driver
commit 15b23906347c ("PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()").
Fixes: 10a797c6e54a ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Link: https://lore.kernel.org/r/20240524105714.191642-3-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c174b53e95adf2eece2afc56cd9798374919f99a upstream.
In the ad7780_write_raw() , val2 can be zero, which might lead to a
division by zero error in DIV_ROUND_CLOSEST(). The ad7780_write_raw()
is based on iio_info's write_raw. While val is explicitly declared that
can be zero (in read mode), val2 is not specified to be non-zero.
Fixes: 9085daa4abcc ("staging: iio: ad7780: add gain & filter gpio support")
Cc: stable@vger.kernel.org
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Link: https://patch.msgid.link/20241028142027.1032332-1-quzicheng@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93efb0c656837f4a31d7cc6117a7c8cecc8fadac upstream.
Code at line 967 implies that rsp->fwdata.supported_fec may be up to 4:
967: if (rsp->fwdata.supported_fec <= FEC_MAX_INDEX)
If rsp->fwdata.supported_fec evaluates to 4, then there is an
out-of-bounds read at line 971 because fec is an array with
a maximum of 4 elements:
954 const int fec[] = {
955 ETHTOOL_FEC_OFF,
956 ETHTOOL_FEC_BASER,
957 ETHTOOL_FEC_RS,
958 ETHTOOL_FEC_BASER | ETHTOOL_FEC_RS};
959 #define FEC_MAX_INDEX 4
971: fecparam->fec = fec[rsp->fwdata.supported_fec];
Fix this by properly indexing fec[] with rsp->fwdata.supported_fec - 1.
In this case the proper indexes 0 to 3 are used when
rsp->fwdata.supported_fec evaluates to a range of 1 to 4, correspondingly.
Fixes: d0cf9503e908 ("octeontx2-pf: ethtool fec mode support")
Addresses-Coverity-ID: 1501722 ("Out-of-bounds read")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63e72e551942642c48456a4134975136cdcb9b3c ]
In the error handling for this function, d is freed without ever
removing it from intc_list which would lead to a use after free.
To fix this, let's only add it to the list after everything has
succeeded.
Fixes: 2dcec7a988a1 ("sh: intc: set_irq_wake() support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0779a0dcf41a6452ac0a169cd96863feb5787c7 ]
The undervoltage flags reported by the RTC are useful to know if the
time and date are reliable after a reboot. Although the threshold VLOW1
indicates that the thermometer has been shutdown and time compensation
is off, it doesn't mean that the temperature readout is currently
impossible.
As the system is running, the RTC voltage is now fully established and
we can read the temperature.
Fixes: 67075b63cce2 ("rtc: add AB-RTCMC-32.768kHz-EOZ9 RTC support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/20241122101031.68916-3-maxime.chevallier@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcddf52b7a17adcebc768d26f4e27cf79adb424c ]
Since commit 4c39529663b9 ("slab: Warn on duplicate cache names when
DEBUG_VM=y"), the duplicate slab cache names can be detected and a
kernel WARNING is thrown out.
In UBI fast attaching process, alloc_ai() could be invoked twice
with the same slab cache name 'ubi_aeb_slab_cache', which will trigger
following warning messages:
kmem_cache of name 'ubi_aeb_slab_cache' already exists
WARNING: CPU: 0 PID: 7519 at mm/slab_common.c:107
__kmem_cache_create_args+0x100/0x5f0
Modules linked in: ubi(+) nandsim [last unloaded: nandsim]
CPU: 0 UID: 0 PID: 7519 Comm: modprobe Tainted: G 6.12.0-rc2
RIP: 0010:__kmem_cache_create_args+0x100/0x5f0
Call Trace:
__kmem_cache_create_args+0x100/0x5f0
alloc_ai+0x295/0x3f0 [ubi]
ubi_attach+0x3c3/0xcc0 [ubi]
ubi_attach_mtd_dev+0x17cf/0x3fa0 [ubi]
ubi_init+0x3fb/0x800 [ubi]
do_init_module+0x265/0x7d0
__x64_sys_finit_module+0x7a/0xc0
The problem could be easily reproduced by loading UBI device by fastmap
with CONFIG_DEBUG_VM=y.
Fix it by using different slab names for alloc_ai() callers.
Fixes: d2158f69a7d4 ("UBI: Remove alloc_ai() slab name from parameter list")
Fixes: fdf10ed710c0 ("ubi: Rework Fastmap attach base code")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8ba8a2bc4f60a1065f23d6a0e7cbea945a0f40d ]
If the __rtc_read_time call fails,, the struct rtc_time tm; may contain
uninitialized data, or an illegal date/time read from the RTC hardware.
When calling rtc_tm_to_ktime later, the result may be a very large value
(possibly KTIME_MAX). If there are periodic timers in rtc->timerqueue,
they will continually expire, may causing kernel softlockup.
Fixes: 6610e0893b8b ("RTC: Rework RTC code to use timerqueue for events")
Signed-off-by: Yongliang Gao <leonylgao@tencent.com>
Acked-by: Jingqun Li <jingqunli@tencent.com>
Link: https://lore.kernel.org/r/20241011043153.3788112-1-leonylgao@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6cd7adec0cf03f0aefc55676e71dd721cbc71a8 ]
If request_irq() fails in st_rtc_probe(), there is no need to enable
the irq, and if it succeeds, disable_irq() after request_irq() still has
a time gap in which interrupts can come.
request_irq() with IRQF_NO_AUTOEN flag will disable IRQ auto-enable when
request IRQ.
Fixes: b5b2bdfc2893 ("rtc: st: Add new driver for ST's LPC RTC")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20240912033727.3013951-1-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7a68f9fa97357a0f2073c9c31ed4101da4fce93e upstream.
As support for splitting transmission over several messages using
TX_DATA_CONT was introduced it does not immediately return the return
value of qcom_glink_tx().
The result is that in the intentless case (i.e. intent == NULL), the
code will continue to send all additional chunks. This is wasteful, and
it's possible that the send operation could incorrectly indicate
success, if the last chunk fits in the TX fifo.
Fix the condition.
Fixes: 8956927faed3 ("rpmsg: glink: Add TX_DATA_CONT command while sending")
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230418163018.785524-2-quic_bjorande@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7fc65f5141c24785dc8c19249ca4efcf71b3524 upstream.
The dwc3_request->num_queued_sgs is decremented on completion. If a
partially completed request is handled, then the
dwc3_request->num_queued_sgs no longer reflects the total number of
num_queued_sgs (it would be cleared).
Correctly check the number of request SG entries remained to be prepare
and queued. Failure to do this may cause null pointer dereference when
accessing non-existent SG entry.
Cc: stable@vger.kernel.org
Fixes: c96e6725db9d ("usb: dwc3: gadget: Correct the logic for queuing sgs")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d07a7c4aa0fcf746cdca0515150dbe5c52000af7.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02a6982b0ccfcdc39e20016f5fc9a1b7826a6ee7 upstream.
The check whether the TRB ring is full or empty in dwc3_calc_trbs_left()
is insufficient. It assumes there are active TRBs if there's any request
in the started_list. However, that's not the case for requests with a
large SG list.
That is, if we have a single usb request that requires more TRBs than
the total TRBs in the TRB ring, the queued TRBs will be available when
all the TRBs in the ring are completed. But the request is only
partially completed and remains in the started_list. With the current
logic, the TRB ring is empty, but dwc3_calc_trbs_left() returns 0.
Fix this by additionally checking for the request->num_trbs for active
TRB count.
Cc: stable@vger.kernel.org
Fixes: 51f1954ad853 ("usb: dwc3: gadget: Fix dwc3_calc_trbs_left()")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/708dc62b56b77da1f704cc2ae9b6ddb1f2dbef1f.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f070b1862f3411b8bcdfd51a8eaad25286f9deb upstream.
The v4l2_detect_cvt/gtf functions should check the result against the
timing capabilities: these functions calculate the timings, so if they
are out of bounds, they should be rejected.
To do this, add the struct v4l2_dv_timings_cap as argument to those
functions.
This required updates to the adv7604 and adv7842 drivers since the
prototype of these functions has now changed. The timings struct
that is passed to v4l2_detect_cvt/gtf in those two drivers is filled
with the timings detected by the hardware.
The vivid driver was also updated, but an additional check was added:
the width and height specified by VIDIOC_S_DV_TIMINGS has to match the
calculated result, otherwise something went wrong. Note that vivid
*emulates* hardware, so all the values passed to the v4l2_detect_cvt/gtf
functions came from the timings struct that was filled by userspace
and passed on to the driver via VIDIOC_S_DV_TIMINGS. So these fields
can contain random data. Both the constraints check via
struct v4l2_dv_timings_cap and the additional width/height check
ensure that the resulting timings are sane and not messed up by the
v4l2_detect_cvt/gtf calculations.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Fixes: 2576415846bc ("[media] v4l2: move dv-timings related code to v4l2-dv-timings.c")
Cc: stable@vger.kernel.org
Reported-by: syzbot+a828133770f62293563e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-media/000000000000013050062127830a@google.com/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca59f9956d4519ab18ab2270be47c6b8c6ced091 upstream.
Atomicity violation occurs when the fmc_send_cmd() function is executed
simultaneously with the modification of the fmdev->resp_skb value.
Consider a scenario where, after passing the validity check within the
function, a non-null fmdev->resp_skb variable is assigned a null value.
This results in an invalid fmdev->resp_skb variable passing the validity
check. As seen in the later part of the function, skb = fmdev->resp_skb;
when the invalid fmdev->resp_skb passes the check, a null pointer
dereference error may occur at line 478, evt_hdr = (void *)skb->data;
To address this issue, it is recommended to include the validity check of
fmdev->resp_skb within the locked section of the function. This
modification ensures that the value of fmdev->resp_skb does not change
during the validation process, thereby maintaining its validity.
This possible bug is found by an experimental static analysis tool
developed by our team. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations.
Fixes: e8454ff7b9a4 ("[media] drivers:media:radio: wl128x: FM Driver Common sources")
Cc: stable@vger.kernel.org
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49a397ad24ee5e2c53a59dada2780d7e71bd3f77 upstream.
The tilt data contained in the Bluetooth packets of an Intuos Pro are
supposed to be interpreted as signed values. Simply casting the values
to type `char` is not guaranteed to work since it is implementation-
defined whether it is signed or unsigned. At least one user has noticed
the data being reported incorrectly on their system. To ensure that the
data is interpreted properly, we specifically cast to `signed char`
instead.
Link: https://github.com/linuxwacom/input-wacom/issues/445
Fixes: 4922cd26f03c ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
CC: stable@vger.kernel.org # 4.11+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcc7ba668818dcadd2f1db66b39ed860a63ecf97 upstream.
Currently in omap_8250_shutdown, the dma->rx_running flag is
set to zero in omap_8250_rx_dma_flush. Next pm_runtime_get_sync
is called, which is a runtime resume call stack which can
re-set the flag. When the call omap_8250_shutdown returns, the
flag is expected to be UN-SET, but this is not the case. This
is causing issues the next time UART is re-opened and
omap_8250_rx_dma is called. Fix by moving pm_runtime_get_sync
before the omap_8250_rx_dma_flush.
cc: stable@vger.kernel.org
Fixes: 0e31c8d173ab ("tty: serial: 8250_omap: add custom DMA-RX callback")
Signed-off-by: Bin Liu <b-liu@ti.com>
[Judith: Add commit message]
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20241031172315.453750-1-jm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d610020f030bec819f42de327c2bd5437d2766b3 upstream.
During wear-leveing work, the source PEB will be moved into scrub list
when source LEB cannot be locked in ubi_eba_copy_leb(), which is wrong
for non-scrub type source PEB. The problem could bring extra and
ineffective wear-leveing jobs, which makes more or less negative effects
for the life time of flash. Specifically, the process is divided 2 steps:
1. wear_leveling_worker // generate false scrub type PEB
ubi_eba_copy_leb // MOVE_RETRY is returned
leb_write_trylock // trylock failed
scrubbing = 1;
e1 is put into ubi->scrub
2. wear_leveling_worker // schedule false scrub type PEB for wl
scrubbing = 1
e1 = rb_entry(rb_first(&ubi->scrub))
The problem can be reproduced easily by running fsstress on a small
UBIFS partition(<64M, simulated by nandsim) for 5~10mins
(CONFIG_MTD_UBI_FASTMAP=y,CONFIG_MTD_UBI_WL_THRESHOLD=50). Following
message is shown:
ubi0: scrubbed PEB 66 (LEB 0:10), data moved to PEB 165
Since scrub type source PEB has set variable scrubbing as '1', and
variable scrubbing is checked before variable keep, so the problem can
be fixed by setting keep variable as 1 directly if the source LEB cannot
be locked.
Fixes: e801e128b220 ("UBI: fix missing scrub when there is a bit-flip")
CC: stable@vger.kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c41f371457bd9a24874e3c7934d9745e87fbc58 upstream.
The device_for_each_child_node() macro requires explicit calls to
fwnode_handle_put() upon early exits (return, break, goto) to decrement
the fwnode's refcount, and avoid levaing a node reference behind.
Add the missing fwnode_handle_put() after the common label for all error
paths.
Cc: stable@vger.kernel.org
Fixes: fdc6b21e2444 ("platform/chrome: Add Type C connector class driver")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241013-cross_ec_typec_fwnode_handle_put-v2-1-9182b2cd7767@gmail.com
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d24cfee7f63d6b44d45a67c5662bd1cc48e8b3ca upstream.
When probing spi device take care of deferred probe of ACPI irq gpio
similar like for OF/DT case.
>From practical standpoint this fixes issue with vsc-tp driver on
Dell XP 9340 laptop, which try to request interrupt with spi->irq
equal to -EPROBE_DEFER and fail to probe with the following error:
vsc-tp spi-INTC10D0:00: probe with driver vsc-tp failed with error -22
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: 33ada67da352 ("ACPI / spi: attach GPIO IRQ from ACPI description to SPI device")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Alexis Lothoré <alexis.lothore@bootlin.com> # Dell XPS9320, ov01a10
Link: https://patch.msgid.link/20241122094224.226773-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 718632467d88e98816fa01ab12681ef1c2aa56f8 upstream.
This reverts commit 3791ea69a4858b81e0277f695ca40f5aae40f312.
It was reported to cause boot-time issues, so revert it for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 3791ea69a485 ("serial: sh-sci: Clean sci_ports[0] after at earlycon exit")
Cc: stable <stable@kernel.org>
Cc: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3791ea69a4858b81e0277f695ca40f5aae40f312 upstream.
The early_console_setup() function initializes the sci_ports[0].port with
an object of type struct uart_port obtained from the object of type
struct earlycon_device received as argument by the early_console_setup().
It may happen that later, when the rest of the serial ports are probed,
the serial port that was used as earlycon (e.g., port A) to be mapped to a
different position in sci_ports[] and the slot 0 to be used by a different
serial port (e.g., port B), as follows:
sci_ports[0] = port A
sci_ports[X] = port B
In this case, the new port mapped at index zero will have associated data
that was used for earlycon.
In case this happens, after Linux boot, any access to the serial port that
maps on sci_ports[0] (port A) will block the serial port that was used as
earlycon (port B).
To fix this, add early_console_exit() that clean the sci_ports[0] at
earlycon exit time.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241106120118.1719888-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51cdd69d6a857f527d6d0697a2e1f0fa8bca1005 upstream.
This reverts commit ec6ce7075ef879b91a8710829016005dc8170f17.
Fix installation of WinUSB driver using OS descriptors. Without the
fix the drivers are not installed correctly and the property
'DeviceInterfaceGUID' is missing on host side.
The original change was based on the assumption that the interface
number is in the high byte of wValue but it is in the low byte,
instead. Unfortunately, the fix is based on MS documentation which is
also wrong.
The actual USB request for OS descriptors (using USB analyzer) looks
like:
Offset 0 1 2 3 4 5 6 7
0x000 C1 A1 02 00 05 00 0A 00
C1: bmRequestType (device to host, vendor, interface)
A1: nas magic number
0002: wValue (2: nas interface)
0005: wIndex (5: get extended property i.e. nas interface GUID)
008E: wLength (142)
The fix was tested on Windows 10 and Windows 11.
Cc: stable@vger.kernel.org
Fixes: ec6ce7075ef8 ("usb: gadget: composite: fix OS descriptors w_value logic")
Signed-off-by: Michal Vrastil <michal.vrastil@hidglobal.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Peter korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20241113235433.20244-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfa54a793ba77ef696755b66f3ac4ed00c7d1248 upstream.
For bus_register(), any error which happens after kset_register() will
cause that @priv are freed twice, fixed by setting @priv with NULL after
the first free.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240727-bus_register_fix-v1-1-fed8dd0dba7a@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Brennan : Backport requires bus->p = NULL instead of priv = NULL ]
Signed-off-by: Brennan Lamoreaux <brennan.lamoreaux@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 635a9fca54f4f4148be1ae1c7c6bd37af80f5773 upstream.
Commit 7c0cca7c847e ("tty: ldisc: add sysctl to prevent autoloading of
ldiscs") introduces the tty_ldisc_autoload sysctl with the wrong
proc_handler. .extra1 and .extra2 parameters are set to avoid other values
thant SYSCTL_ZERO or SYSCTL_ONE to be set but proc_dointvec do not uses
them.
This commit fixes this by using proc_dointvec_minmax instead of
proc_dointvec.
Fixes: 7c0cca7c847e ("tty: ldisc: add sysctl to prevent autoloading of ldiscs")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Bouchinet <nicolas.bouchinet@ssi.gouv.fr>
Reviewed-by: Lin Feng <linf@wangsu.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20241112131357.49582-4-nicolas.bouchinet@clip-os.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce8f9fb651fac95dd41f69afe54d935420b945bd upstream.
If some remap_pfn_range() calls succeeded before one failed, we still have
buffer pages mapped into the userspace page tables when we drop the buffer
reference with comedi_buf_map_put(bm). The userspace mappings are only
cleaned up later in the mmap error path.
Fix it by explicitly flushing all mappings in our VMA on the error path.
See commit 79a61cc3fc04 ("mm: avoid leaving partial pfn mappings around in
error case").
Cc: stable@vger.kernel.org
Fixes: ed9eccbe8970 ("Staging: add comedi core")
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20241017-comedi-tlb-v3-1-16b82f9372ce@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7acef99642b763ba585f4a43af999fcdbcc3dc4 upstream.
Dennis reports a boot crash on recent Lenovo laptops with a USB4 dock.
Since commit 0fc70886569c ("thunderbolt: Reset USB4 v2 host router") and
commit 59a54c5f3dbd ("thunderbolt: Reset topology created by the boot
firmware"), USB4 v2 and v1 Host Routers are reset on probe of the
thunderbolt driver.
The reset clears the Presence Detect State and Data Link Layer Link Active
bits at the USB4 Host Router's Root Port and thus causes hot removal of the
dock.
The crash occurs when pciehp is unbound from one of the dock's Downstream
Ports: pciehp creates a pci_slot on bind and destroys it on unbind. The
pci_slot contains a pointer to the pci_bus below the Downstream Port, but
a reference on that pci_bus is never acquired. The pci_bus is destroyed
before the pci_slot, so a use-after-free ensues when pci_slot_release()
accesses slot->bus.
In principle this should not happen because pci_stop_bus_device() unbinds
pciehp (and therefore destroys the pci_slot) before the pci_bus is
destroyed by pci_remove_bus_device().
However the stacktrace provided by Dennis shows that pciehp is unbound from
pci_remove_bus_device() instead of pci_stop_bus_device(). To understand
the significance of this, one needs to know that the PCI core uses a two
step process to remove a portion of the hierarchy: It first unbinds all
drivers in the sub-hierarchy in pci_stop_bus_device() and then actually
removes the devices in pci_remove_bus_device(). There is no precaution to
prevent driver binding in-between pci_stop_bus_device() and
pci_remove_bus_device().
In Dennis' case, it seems removal of the hierarchy by pciehp races with
driver binding by pci_bus_add_devices(). pciehp is bound to the
Downstream Port after pci_stop_bus_device() has run, so it is unbound by
pci_remove_bus_device() instead of pci_stop_bus_device(). Because the
pci_bus has already been destroyed at that point, accesses to it result in
a use-after-free.
One might conclude that driver binding needs to be prevented after
pci_stop_bus_device() has run. However it seems risky that pci_slot points
to pci_bus without holding a reference. Solely relying on correct ordering
of driver unbind versus pci_bus destruction is certainly not defensive
programming.
If pci_slot has a need to access data in pci_bus, it ought to acquire a
reference. Amend pci_create_slot() accordingly. Dennis reports that the
crash is not reproducible with this change.
Abridged stacktrace:
pcieport 0000:00:07.0: PME: Signaling with IRQ 156
pcieport 0000:00:07.0: pciehp: Slot #12 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+
pci_bus 0000:20: dev 00, created physical slot 12
pcieport 0000:00:07.0: pciehp: Slot(12): Card not present
...
pcieport 0000:21:02.0: pciehp: pcie_disable_notification: SLOTCTRL d8 write cmd 0
Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] PREEMPT SMP NOPTI
CPU: 13 UID: 0 PID: 134 Comm: irq/156-pciehp Not tainted 6.11.0-devel+ #1
RIP: 0010:dev_driver_string+0x12/0x40
pci_destroy_slot
pciehp_remove
pcie_port_remove_service
device_release_driver_internal
bus_remove_device
device_del
device_unregister
remove_iter
device_for_each_child
pcie_portdrv_remove
pci_device_remove
device_release_driver_internal
bus_remove_device
device_del
pci_remove_bus_device (recursive invocation)
pci_remove_bus_device
pciehp_unconfigure_device
pciehp_disable_slot
pciehp_handle_presence_or_link_change
pciehp_ist
Link: https://lore.kernel.org/r/4bfd4c0e976c1776cd08e76603903b338cf25729.1728579288.git.lukas@wunner.de
Reported-by: Dennis Wassenberg <Dennis.Wassenberg@secunet.com>
Closes: https://lore.kernel.org/r/6de4b45ff2b32dd91a805ec02ec8ec73ef411bf6.camel@secunet.com/
Tested-by: Dennis Wassenberg <Dennis.Wassenberg@secunet.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 128fdbf36cddc2a901c4889ba1c89fa9f2643f2c upstream.
In success case, the revision holds a non-null pointer. The current
logic incorrectly returns an error for a non-null pointer, whereas
it should return an error for a null pointer.
The socinfo driver for IPQ9574 and IPQ5332 is currently broken,
resulting in the following error message
qcom-socinfo qcom-socinfo: probe with driver qcom-socinfo failed with
error -12
Add a null check for the revision to ensure it returns an error only in
failure case (null pointer).
Fixes: e694d2b5c58b ("soc: qcom: Add check devm_kasprintf() returned value")
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241016144852.2888679-1-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c974826734836402abfd44efbf04f63a2cc1c1 upstream.
If the clock sehci->clk was not enabled in spear_ehci_hcd_drv_probe,
it should not be disabled in any path.
Conversely, if it was enabled in spear_ehci_hcd_drv_probe, it must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 7675d6ba436f ("USB: EHCI: make ehci-spear a separate driver")
Cc: stable@vger.kernel.org
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241114230310.432213-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afc545da381ba0c651b2658966ac737032676f01 upstream.
This patch fixes an issue in the function xenbus_dev_probe(). In the
xenbus_dev_probe() function, within the if (err) branch at line 313, the
program incorrectly returns err directly without releasing the resources
allocated by err = drv->probe(dev, id). As the return value is non-zero,
the upper layers assume the processing logic has failed. However, the probe
operation was performed earlier without a corresponding remove operation.
Since the probe actually allocates resources, failing to perform the remove
operation could lead to problems.
To fix this issue, we followed the resource release logic of the
xenbus_dev_remove() function by adding a new block fail_remove before the
fail_put block. After entering the branch if (err) at line 313, the
function will use a goto statement to jump to the fail_remove block,
ensuring that the previously acquired resources are correctly released,
thus preventing the reference count leak.
This bug was identified by an experimental static analysis tool developed
by our team. The tool specializes in analyzing reference count operations
and detecting potential issues where resources are not properly managed.
In this case, the tool flagged the missing release operation as a
potential problem, which led to the development of this patch.
Fixes: 4bac07c993d0 ("xen: add the Xenbus sysfs and virtual device hotplug driver")
Cc: stable@vger.kernel.org
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Message-ID: <20241105130919.4621-1-chenqiuji666@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d38be702452137fa82a56ff7cc577d829add1637 ]
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when not
used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected but might as well be left unset when it is not
known.
The type parameter could be used to set the UART type, but is
better left unspecified (type unknown) when it isn't used.
Note that some applications have historically expected TIOCGSERIAL to be
implemented, but judging from the Debian sources, the port type not
being PORT_UNKNOWN is only used to check for the existence of legacy
serial ports (ttySn). Notably USB serial drivers like ftdi_sio have been
using PORT_UNKNOWN for twenty years without any problems.
Drop the bogus values provided by the greybus implementation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407102334.32361-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: fe0ebeafc3b7 ("staging: greybus: uart: Fix atomicity violation in get_serial_info()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
