[ Upstream commit a024e377efed31ecfb39210bed562932321345b3 ]
802.2+LLC+SNAP frames received by napi_complete_done with GRO and DSA
have skb->transport_header set two bytes short, or pointing 2 bytes
before network_header & skb->data. As snap_rcv expects transport_header
to point to SNAP header (OID:PID) after LLC processing advances offset
over LLC header (llc_rcv & llc_fixup_skb), code doesn't find a match
and packet is dropped.
Between napi_complete_done and snap_rcv, transport_header is not used
until __netif_receive_skb_core, where originally it was being reset.
Commit fda55eca5a33 ("net: introduce skb_transport_header_was_set()")
only does so if not set, on the assumption the value was set correctly
by GRO (and also on assumption that "network stacks usually reset the
transport header anyway"). Afterwards it is moved forward by
llc_fixup_skb.
Locally generated traffic shows up at __netif_receive_skb_core with no
transport_header set and is processed without issue. On a setup with
GRO but no DSA, transport_header and network_header are both set to
point to skb->data which is also correct.
As issue is LLC specific, to avoid impacting non-LLC traffic, and to
follow up on original assumption made on previous code change,
llc_fixup_skb to reset the offset after skb pull. llc_fixup_skb
assumes the LLC header is at skb->data, and by definition SNAP header
immediately follows.
Fixes: fda55eca5a33 ("net: introduce skb_transport_header_was_set()")
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241225010723.2830290-1-antonio.pastor@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 902806baf3c1e8383c1fe3ff0b6042b8cb5c2707 ]
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
- In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
before/after setting ADV7511_REG_AUDIO_INFOFRAME.
- In audio_startup() use the correct register for clearing
AUDIO_UPDATE bit.
The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.
Note that this patchs replaces writing REG_GC(1) with
REG_INFOFRAME_UPDATE. Bit 5 of REG_GC(1) is positioned within field
GC_PP[3:0] and that field doesn't control audio infoframe and is read-
only. My conclusion therefore was that the author if this code meant to
clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning.
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 53c515befe28 ("drm/bridge: adv7511: Add Audio support")
Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119-adv7511-audio-info-frame-v4-1-4ae68e76c89c@axis.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9272cba0ded71b5a2084da3004ec7806b8cb7fd2 ]
QP table handling is synchronized with destroy QP and Async
event from the HW. The same needs to be synchronized
during create_qp also. Use the same lock in create_qp also.
Fixes: 76d3ddff7153 ("RDMA/bnxt_re: synchronize the qp-handle table array")
Fixes: f218d67ef004 ("RDMA/bnxt_re: Allow posting when QPs are in error")
Fixes: 84cf229f4001 ("RDMA/bnxt_re: Fix the qp table indexing")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241217102649.1377704-6-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c63e1c4dfc33d1bdae395ee8fbcbfad4830b12c0 ]
While creating qps, the driver adds one extra entry to the sq size passed
by the ULPs in order to avoid queue full condition. When ULPs creates QPs
with max_qp_wr reported, driver creates QP with 1 more than the max_wqes
supported by HW. Create QP fails in this case. To avoid this error, reduce
1 entry in max_qp_wqes and report it to the stack.
Link: https://lore.kernel.org/r/1606741986-16477-1-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7179fe0074a3c962e43a9e51169304c4911989ed ]
Driver currently populates subsystem_device id in the
"hw_ver" field of ib_attr structure in query_device.
Updated to populate PCI revision ID.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Preethi G <preethi.gurusiddalingeswaraswamy@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-6-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 798653a0ee30d3cd495099282751c0f248614ae7 ]
When RDMA app configures path MTU, add a check in modify_qp verb
to make sure that it doesn't go beyond interface MTU. If this
check fails, driver will fail the modify_qp verb.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e05feab22fd7dabcd6d272c4e2401ec1acdfdb9b ]
Different core device types such as PFs and VFs shouldn't be affiliated
together since they have different capabilities, fix that by enforcing
type check before doing the affiliation.
Fixes: 32f69e4be269 ("{net, IB}/mlx5: Manage port association for multiport RoCE")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/88699500f690dff1c1852c1ddb71f8a1cc8b956e.1733233480.git.leonro@nvidia.com
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b1e58aa832ed537289be6a51a2015309688a90c ]
Subsequent patch implements helper API which has mlx5_core_dev
as const pointer, make its caller API too const *.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: e05feab22fd7 ("RDMA/mlx5: Enforce same type port association for multiport RoCE")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8644b48714dca8bf2f42a4ff8311de8efc9bd8c3 ]
Intel Panther Lake-M/P has the same integrated Thunderbolt/USB4
controller as Lunar Lake. Add these PCI IDs to the driver list of
supported devices.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cd3da4e37453019e21a486d9de3144f46b4fdf7 ]
Intel Lunar Lake has similar integrated Thunderbolt/USB4 controller as
Intel Meteor Lake with some small differences in the host router (it has
3 DP IN adapters for instance). Add the Intel Lunar Lake PCI IDs to the
driver list of supported devices.
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Stable-dep-of: 8644b48714dc ("thunderbolt: Add support for Intel Panther Lake-M/P")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f14a210661ce03988ef4ed3c8402037c8e06539 ]
Intel Barlow Ridge is the first USB4 v2 controller from Intel. The
controller exposes standard USB4 PCI class ID in typical configurations,
however there is a way to configure it so that it uses a special class
ID to allow using s different driver than the Windows inbox one. For
this reason add the Barlow Ridge PCI ID to the Linux driver too so that
the driver can attach regardless of the class ID.
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Stable-dep-of: 8644b48714dc ("thunderbolt: Add support for Intel Panther Lake-M/P")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32249fd8c8cccd7a1ed86c3b6d9b6ae9b4a83623 ]
Intel Meteor Lake has the same integrated Thunderbolt/USB4 controller as
Intel Alder Lake. Add the Intel Meteor Lake PCI IDs to the driver list
of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Stable-dep-of: 8644b48714dc ("thunderbolt: Add support for Intel Panther Lake-M/P")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ec58378a985618909ffae18e4ac0de2ae625f33 ]
Intel Raptor Lake has the same integrated Thunderbolt/USB4 controller as
Intel Alder Lake. By default it is still using firmware based connection
manager so we can use most of the Alder Lake flows.
Signed-off-by: George D Sworo <george.d.sworo@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Stable-dep-of: 8644b48714dc ("thunderbolt: Add support for Intel Panther Lake-M/P")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 135794868ad83d0327cdd78df469e118f1fe7cc4 ]
Alder Lake has the same integrated Thunderbolt/USB4 controller as
Intel Tiger Lake. By default it is still using firmware based connection
manager so we can use most of the Tiger Lake flows.
Add the Alder Lake PCI IDs to the driver list of supported devices.
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Stable-dep-of: 8644b48714dc ("thunderbolt: Add support for Intel Panther Lake-M/P")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 900f83cf376bdaf798b6f5dcb2eae0c822e908b6 upstream.
When evaluating extended permissions, ignore unknown permissions instead
of calling BUG(). This commit ensures that future permissions can be
added without interfering with older kernels.
Cc: stable@vger.kernel.org
Fixes: fa1aa143ac4a ("selinux: extended permissions for ioctls")
Signed-off-by: Thiébaud Weksteen <tweek@google.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcc80dec91ee745b3d66f3e48f0ec2efdea97149 upstream.
read_hv_sched_clock_tsc() assumes that the Hyper-V clock counter is
bigger than the variable hv_sched_clock_offset, which is cached during
early boot, but depending on the timing this assumption may be false
when a hibernated VM starts again (the clock counter starts from 0
again) and is resuming back (Note: hv_init_tsc_clocksource() is not
called during hibernation/resume); consequently,
read_hv_sched_clock_tsc() may return a negative integer (which is
interpreted as a huge positive integer since the return type is u64)
and new kernel messages are prefixed with huge timestamps before
read_hv_sched_clock_tsc() grows big enough (which typically takes
several seconds).
Fix the issue by saving the Hyper-V clock counter just before the
suspend, and using it to correct the hv_sched_clock_offset in
resume. This makes hv tsc page based sched_clock continuous and ensures
that post resume, it starts from where it left off during suspend.
Override x86_platform.save_sched_clock_state and
x86_platform.restore_sched_clock_state routines to correct this as soon
as possible.
Note: if Invariant TSC is available, the issue doesn't happen because
1) we don't register read_hv_sched_clock_tsc() for sched clock:
See commit e5313f1c5404 ("clocksource/drivers/hyper-v: Rework
clocksource and sched clock setup");
2) the common x86 code adjusts TSC similarly: see
__restore_processor_state() -> tsc_verify_tsc_adjust(true) and
x86_platform.restore_sched_clock_state().
Cc: stable@vger.kernel.org
Fixes: 1349401ff1aa ("clocksource/drivers/hyper-v: Suspend/resume Hyper-V clocksource for hibernation")
Co-developed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240917053917.76787-1-namjain@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240917053917.76787-1-namjain@linux.microsoft.com>
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f678def99d29c520418607509bb19c7fc96a6db upstream.
Christoph Paasch reports [1] about incorrect skb->truesize
after skb_expand_head() call in ip6_xmit.
This may happen because of two reasons:
- skb_set_owner_w() for newly cloned skb is called too early,
before pskb_expand_head() where truesize is adjusted for (!skb-sk) case.
- pskb_expand_head() does not adjust truesize in (skb->sk) case.
In this case sk->sk_wmem_alloc should be adjusted too.
[1] https://lkml.org/lkml/2021/8/20/1082
Fixes: f1260ff15a71 ("skbuff: introduce skb_expand_head()")
Fixes: 2d85a1b31dde ("ipv6: ip6_finish_output2: set sk into newly allocated nskb")
Reported-by: Christoph Paasch <christoph.paasch@gmail.com>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/644330dd-477e-0462-83bf-9f514c41edd1@virtuozzo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5ff2fb2e7167e9483846e34148e60c0c016a1f6 upstream.
In the normal case, when we excute `echo 0 > /proc/fs/nfsd/threads`, the
function `nfs4_state_destroy_net` in `nfs4_state_shutdown_net` will
release all resources related to the hashed `nfs4_client`. If the
`nfsd_client_shrinker` is running concurrently, the `expire_client`
function will first unhash this client and then destroy it. This can
lead to the following warning. Additionally, numerous use-after-free
errors may occur as well.
nfsd_client_shrinker echo 0 > /proc/fs/nfsd/threads
expire_client nfsd_shutdown_net
unhash_client ...
nfs4_state_shutdown_net
/* won't wait shrinker exit */
/* cancel_work(&nn->nfsd_shrinker_work)
* nfsd_file for this /* won't destroy unhashed client1 */
* client1 still alive nfs4_state_destroy_net
*/
nfsd_file_cache_shutdown
/* trigger warning */
kmem_cache_destroy(nfsd_file_slab)
kmem_cache_destroy(nfsd_file_mark_slab)
/* release nfsd_file and mark */
__destroy_client
====================================================================
BUG nfsd_file (Not tainted): Objects remaining in nfsd_file on
__kmem_cache_shutdown()
--------------------------------------------------------------------
CPU: 4 UID: 0 PID: 764 Comm: sh Not tainted 6.12.0-rc3+ #1
dump_stack_lvl+0x53/0x70
slab_err+0xb0/0xf0
__kmem_cache_shutdown+0x15c/0x310
kmem_cache_destroy+0x66/0x160
nfsd_file_cache_shutdown+0xac/0x210 [nfsd]
nfsd_destroy_serv+0x251/0x2a0 [nfsd]
nfsd_svc+0x125/0x1e0 [nfsd]
write_threads+0x16a/0x2a0 [nfsd]
nfsctl_transaction_write+0x74/0xa0 [nfsd]
vfs_write+0x1a5/0x6d0
ksys_write+0xc1/0x160
do_syscall_64+0x5f/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
====================================================================
BUG nfsd_file_mark (Tainted: G B W ): Objects remaining
nfsd_file_mark on __kmem_cache_shutdown()
--------------------------------------------------------------------
dump_stack_lvl+0x53/0x70
slab_err+0xb0/0xf0
__kmem_cache_shutdown+0x15c/0x310
kmem_cache_destroy+0x66/0x160
nfsd_file_cache_shutdown+0xc8/0x210 [nfsd]
nfsd_destroy_serv+0x251/0x2a0 [nfsd]
nfsd_svc+0x125/0x1e0 [nfsd]
write_threads+0x16a/0x2a0 [nfsd]
nfsctl_transaction_write+0x74/0xa0 [nfsd]
vfs_write+0x1a5/0x6d0
ksys_write+0xc1/0x160
do_syscall_64+0x5f/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
To resolve this issue, cancel `nfsd_shrinker_work` using synchronous
mode in nfs4_state_shutdown_net.
Fixes: 7c24fa225081 ("NFSD: replace delayed_work with work_struct for nfsd_client_shrinker")
Signed-off-by: Yang Erkun <yangerkun@huaweicloud.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c8507c63f5498d4ee4af404a8e44ceae4345056 upstream.
During swap activation we iterate over the extents of a file and we can
have many thousands of them, so we can end up in a busy loop monopolizing
a core. Avoid this by doing a voluntary reschedule after processing each
extent.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afc6e39e824ad0e44b2af50a97885caec8d213d1 upstream.
Fix set charge current limits for devices which allow to set the lowest
charge current limit to be greater zero. If requested charge current limit
is below lowest limit, the index equals current_limit_map_size which leads
to accessing memory beyond allocated memory.
Fixes: be2919d8355e ("power: supply: gpio-charger: add charge-current-limit feature")
Cc: stable@vger.kernel.org
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://lore.kernel.org/r/20241209-fix-charge-current-limit-v1-1-760d9b8f2af3@liebherr.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0900d15d31c2597dd9f634c8be2b71762199890 ]
Linux currently sets the TCR_EL1.AS bit unconditionally during CPU
bring-up. On an 8-bit ASID CPU, this is RES0 and ignored, otherwise
16-bit ASIDs are enabled. However, if running in a VM and the hypervisor
reports 8-bit ASIDs (ID_AA64MMFR0_EL1.ASIDBits == 0) on a 16-bit ASIDs
CPU, Linux uses bits 8 to 63 as a generation number for tracking old
process ASIDs. The bottom 8 bits of this generation end up being written
to TTBR1_EL1 and also used for the ASID-based TLBI operations as the
upper 8 bits of the ASID. Following an ASID roll-over event we can have
threads of the same application with the same 8-bit ASID but different
generation numbers running on separate CPUs. Both TLB caching and the
TLBI operations will end up using different actual 16-bit ASIDs for the
same process.
A similar scenario can happen in a big.LITTLE configuration if the boot
CPU only uses 8-bit ASIDs while secondary CPUs have 16-bit ASIDs.
Ensure that the ASID generation is only tracked by bits 16 and up,
leaving bits 15:8 as 0 if the kernel uses 8-bit ASIDs. Note that
clearing TCR_EL1.AS is not sufficient since the architecture requires
that the top 8 bits of the ASID passed to TLBI instructions are 0 rather
than ignored in such configuration.
Cc: stable@vger.kernel.org
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241203151941.353796-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3a5b763410c7bceacf41a52071134d9dc26202a ]
The commit 0c8ea531b774 ("arm64: mm: Allocate ASIDs in pairs") introduce
the asid2idx and idx2asid macro, but these macros are not really useful
after the commit f88f42f853a8 ("arm64: context: Free up kernel ASIDs if
KPTI is not in use").
The code "(asid & ~ASID_MASK)" can be instead by a macro, which is the
same code with asid2idx(). So rename it to ctxid2asid() for a better
understanding.
Also we add asid2ctxid() macro, the contextid can be generated based on
the asid and generation through this macro.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/c31516eb-6d15-94e0-421c-305fc010ea79@huawei.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Stable-dep-of: c0900d15d31c ("arm64: Ensure bits ASID[15:8] are masked out when the kernel uses 8-bit ASIDs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd2fccac61b40eaf08d9546acc9fef958bfe4763 ]
Fix the MST sideband message body length check, which must be at least 1
byte accounting for the message body CRC (aka message data CRC) at the
end of the message.
This fixes a case where an MST branch device returns a header with a
correct header CRC (indicating a correctly received body length), with
the body length being incorrectly set to 0. This will later lead to a
memory corruption in drm_dp_sideband_append_payload() and the following
errors in dmesg:
UBSAN: array-index-out-of-bounds in drivers/gpu/drm/display/drm_dp_mst_topology.c:786:25
index -1 is out of range for type 'u8 [48]'
Call Trace:
drm_dp_sideband_append_payload+0x33d/0x350 [drm_display_helper]
drm_dp_get_one_sb_msg+0x3ce/0x5f0 [drm_display_helper]
drm_dp_mst_hpd_irq_handle_event+0xc8/0x1580 [drm_display_helper]
memcpy: detected field-spanning write (size 18446744073709551615) of single field "&msg->msg[msg->curlen]" at drivers/gpu/drm/display/drm_dp_mst_topology.c:791 (size 256)
Call Trace:
drm_dp_sideband_append_payload+0x324/0x350 [drm_display_helper]
drm_dp_get_one_sb_msg+0x3ce/0x5f0 [drm_display_helper]
drm_dp_mst_hpd_irq_handle_event+0xc8/0x1580 [drm_display_helper]
Cc: <stable@vger.kernel.org>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241125205314.1725887-1-imre.deak@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8ca2a1eeadf09862190b2810697702d803ceef2d upstream.
When the stream_verdict program returns SK_PASS, it places the received skb
into its own receive queue, but a recursive lock eventually occurs, leading
to an operating system deadlock. This issue has been present since v6.9.
'''
sk_psock_strp_data_ready
write_lock_bh(&sk->sk_callback_lock)
strp_data_ready
strp_read_sock
read_sock -> tcp_read_sock
strp_recv
cb.rcv_msg -> sk_psock_strp_read
# now stream_verdict return SK_PASS without peer sock assign
__SK_PASS = sk_psock_map_verd(SK_PASS, NULL)
sk_psock_verdict_apply
sk_psock_skb_ingress_self
sk_psock_skb_ingress_enqueue
sk_psock_data_ready
read_lock_bh(&sk->sk_callback_lock) <= dead lock
'''
This topic has been discussed before, but it has not been fixed.
Previous discussion:
https://lore.kernel.org/all/6684a5864ec86_403d20898@john.notmuch
Fixes: 6648e613226e ("bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue")
Reported-by: Vincent Whitchurch <vincent.whitchurch@datadoghq.com>
Signed-off-by: Jiayuan Chen <mrpre@163.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20241118030910.36230-2-mrpre@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[srish: Apply to stable branch linux-5.10.y]
Signed-off-by: Srish Srinivasan <srishwap4@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8421d4c8762bd022cb491f2f0f7019ef51b4f0a7 upstream.
If a newly-added link type doesn't invoke BPF_LINK_TYPE(), accessing
bpf_link_type_strs[link->type] may result in an out-of-bounds access.
To spot such missed invocations early in the future, checking the
validity of link->type in bpf_link_show_fdinfo() and emitting a warning
when such invocations are missed.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20241024013558.1135167-3-houtao@huaweicloud.com
[ shung-hsi.yu: break up existing seq_printf() call since commit 68b04864ca42
("bpf: Create links for BPF struct_ops maps.") is not present ]
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e891b36de161fcd96f12ff83667473e5067b9037 ]
If skb_expand_head() returns NULL, skb has been freed
and associated dst/idev could also have been freed.
We need to hold rcu_read_lock() to make sure the dst and
associated idev are alive.
Fixes: 5796015fa968 ("ipv6: allocate enough headroom in ip6_finish_output2()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vasily Averin <vasily.averin@linux.dev>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20240820160859.3786976-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit e891b36de161fcd96f12ff83667473e5067b9037)
Signed-off-by: Harshvardhan Jha <harshvardhan.j.jha@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e415ed3a4b8b246ee5e9d109ff5153efcf96b9f2 ]
Unlike skb_realloc_headroom, new helper skb_expand_head does not allocate
a new skb if possible.
Additionally this patch replaces commonly used dereferencing with variables.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit e415ed3a4b8b246ee5e9d109ff5153efcf96b9f2)
Signed-off-by: Harshvardhan Jha <harshvardhan.j.jha@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1260ff15a71b8fc122b2c9abd8a7abffb6e0168 ]
Like skb_realloc_headroom(), new helper increases headroom of specified skb.
Unlike skb_realloc_headroom(), it does not allocate a new skb if possible;
copies skb->sk on new skb when as needed and frees original skb in case
of failures.
This helps to simplify ip[6]_finish_output2() and a few other similar cases.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit f1260ff15a71b8fc122b2c9abd8a7abffb6e0168)
Signed-off-by: Harshvardhan Jha <harshvardhan.j.jha@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18ca63a2e23c5e170d2d7552b64b1f5ad019cd9b ]
msym32 is not supported by LLVM toolchain.
Workaround by probe toolchain support of msym32 for KBUILD_SYM32
feature.
Link: https://github.com/ClangBuiltLinux/linux/issues/1544
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7678abee0867e6b7fb89aa40f6e9f575f755fb37 ]
Commit 4ce6e2db00de ("virtio-blk: Ensure no requests in virtqueues before
deleting vqs.") replaces queue quiesce with queue freeze in virtio-blk's
PM callbacks. And the motivation is to drain inflight IOs before suspending.
block layer's queue freeze looks very handy, but it is also easy to cause
deadlock, such as, any attempt to call into bio_queue_enter() may run into
deadlock if the queue is frozen in current context. There are all kinds
of ->suspend() called in suspend context, so keeping queue frozen in the
whole suspend context isn't one good idea. And Marek reported lockdep
warning[1] caused by virtio-blk's freeze queue in virtblk_freeze().
[1] https://lore.kernel.org/linux-block/ca16370e-d646-4eee-b9cc-87277c89c43c@samsung.com/
Given the motivation is to drain in-flight IOs, it can be done by calling
freeze & unfreeze, meantime restore to previous behavior by keeping queue
quiesced during suspend.
Cc: Yi Sun <yi.sun@unisoc.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: virtualization@lists.linux.dev
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20241112125821.1475793-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1aee7f034615b6824d2c70ddb37ef9fc23493b7 ]
This partially reverts commit 812fe6420a6e ("scsi: storvsc: Handle
additional SRB status values").
HyperV does not support MAINTENANCE_IN resulting in FC passthrough
returning the SRB_STATUS_DATA_OVERRUN value. Now that
SRB_STATUS_DATA_OVERRUN is treated as an error, multipath ALUA paths go
into a faulty state as multipath ALUA submits RTPG commands via
MAINTENANCE_IN.
[ 3.215560] hv_storvsc 1d69d403-9692-4460-89f9-a8cbcc0f94f3:
tag#230 cmd 0xa3 status: scsi 0x0 srb 0x12 hv 0xc0000001
[ 3.215572] scsi 1:0:0:32: alua: rtpg failed, result 458752
Make MAINTENANCE_IN return success to avoid the error path as is
currently done with INQUIRY and MODE_SENSE.
Suggested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Cathy Avery <cavery@redhat.com>
Link: https://lore.kernel.org/r/20241127181324.3318443-1-cavery@redhat.com
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f5eb062e8aa335643181c480e6c590c6cedfd22 ]
Issue a Diag-Reset when the "Doorbell-In-Use" bit is set during the
driver load/initialization.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110173341.11595-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9fba20c29e27dc99e55e1c550573a114561bf8c ]
On the Asus X541UAK an unknown event 0xCF is emited when the charger
is plugged in. This is caused by the following AML code:
If (ACPS ())
{
ACPF = One
Local0 = 0x58
If (ATKP)
{
^^^^ATKD.IANE (0xCF)
}
}
Else
{
ACPF = Zero
Local0 = 0x57
}
Notify (AC0, 0x80) // Status Change
If (ATKP)
{
^^^^ATKD.IANE (Local0)
}
Sleep (0x64)
PNOT ()
Sleep (0x0A)
NBAT (0x80)
Ignore the 0xCF event to silence the unknown event warning.
Reported-by: Pau Espin Pedrol <pespin@espeweb.net>
Closes: https://lore.kernel.org/platform-driver-x86/54d4860b-ec9c-4992-acf6-db3f90388293@espeweb.net
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241123224700.18530-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f1aa0c533d9dd8a835caf9a6824449c463ee7e2 ]
The register addresses are unsigned ints so we should use %u not %d to
log them.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20241127-regmap-test-high-addr-v1-1-74a48a9e0dc5@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 947c4012f8f03a8bb946beb6e5294d5e32817d67 ]
When Z60MR100 startup, speaker will output a pop. To fix this issue,
we mute codec by init verbs in bios when system startup, and set GPIO
to low to unmute codec in codec driver when it loaded .
[ white space fixes and compile warning fix by tiwai ]
Signed-off-by: bo liu <bo.liu@senarytech.com>
Link: https://patch.msgid.link/20241129014441.437205-1-bo.liu@senarytech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c064de86d2a3909222d5996c5047f64c7a8f791b ]
Fix the hardware revision numbering for Qlogic ISP1020/1040 boards. HWMASK
suggests that the revision number only needs four bits, this is consistent
with how NetBSD does things in their ISP driver. Verified on a IPS1040B
which is seen as rev 5 not as BIT_4.
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20241113225636.2276-1-linmag7@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43439076383a7611300334d1357c0f8883f40816 ]
For the watchdog timer to work properly on the QCML04 board we need to
set PWRGD enable in the Environment Controller Configuration Registers
Special Configuration Register 1 when it is not already set, this may
be the case when the watchdog is not enabled from within the BIOS.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241025063441.3494837-1-james.hilliard1@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d685d55dfc86b1a4bdcec77c3c1f8a83f181264e ]
Make sure the trace_kprobe's module notifer callback function is called
after jump_label's callback is called. Since the trace_kprobe's callback
eventually checks jump_label address during registering new kprobe on
the loading module, jump_label must be updated before this registration
happens.
Link: https://lore.kernel.org/all/173387585556.995044.3157941002975446119.stgit@devnote2/
Fixes: 614243181050 ("tracing/kprobes: Support module init function probing")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d8e4771f99c0400a1873235704b28bb803c83d17 upstream.
The "user" pointer was converted from being allocated with kzalloc() to
being allocated by devm_kzalloc(). Calling kfree(user) will lead to a
double free.
Fixes: 6d734f1bfc33 ("mtd: rawnand: atmel: Fix possible memory leak")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c43ec96e8d34399bd9dab2f2dc316b904892133f upstream.
The at_xdmac_memset_create_desc may return NULL, which will lead to a
null pointer dereference. For example, the len input is error, or the
atchan->free_descs_list is empty and memory is exhausted. Therefore, add
check to avoid this.
Fixes: b206d9a23ac7 ("dmaengine: xdmac: Add memset support")
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Link: https://lore.kernel.org/r/20241029082845.1185380-1-chenridong@huaweicloud.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362f1bf98a3ecb5a2a4fcbdaa9718c8403beceb2 upstream.
The for_each_child_of_node() loop requires explicit calls to
of_node_put() to decrement the child's refcount upon early exits (break,
goto, return).
Add the missing calls in the two early exits before the goto
instructions.
Cc: stable@vger.kernel.org
Fixes: f7d12ef53ddf ("dma: mv_xor: add Device Tree binding")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241011-dma_mv_xor_of_node_put-v1-1-3c2de819f463@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dc48c88fcf82b89fdebd83a906aaa64f40fb8a9 upstream.
For devm_phy_destroy(), its comment says it needs to invoke phy_destroy()
to destroy the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_consume(), and the missing
phy_destroy() call will cause that the phy fails to be destroyed.
Fortunately, the faulty API has not been used by current kernel tree.
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff764963479a ("drivers: phy: add generic PHY framework")
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-3-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0b82ab95b4f1fbc3e3aeab9d829d012669524b6 upstream.
For devm_of_phy_provider_unregister(), its comment says it needs to invoke
of_phy_provider_unregister() to unregister the phy provider, but it will
not actually invoke the function since devres_destroy() does not call
devm_phy_provider_release(), and the missing of_phy_provider_unregister()
call will cause:
- The phy provider fails to be unregistered.
- Leak both memory and the OF node refcount.
Fortunately, the faulty API has not been used by current kernel tree.
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff764963479a ("drivers: phy: add generic PHY framework")
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/stable/20241213-phy_core_fix-v6-2-40ae28f5015a%40quicinc.com
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-2-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4bfa9b6d7bd752bfe4700c937f235aa8ce997b upstream.
For devm_phy_put(), its comment says it needs to invoke phy_put() to
release the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_release(), and the missing
phy_put() call will cause:
- The phy fails to be released.
- devm_phy_put() can not fully undo what API devm_phy_get() does.
- Leak refcount of both the module and device for below typical usage:
devm_phy_get(); // or its variant
...
err = do_something();
if (err)
goto err_out;
...
err_out:
devm_phy_put(); // leak refcount here
The file(s) affected by this issue are shown below since they have such
typical usage.
drivers/pci/controller/cadence/pcie-cadence.c
drivers/net/ethernet/ti/am65-cpsw-nuss.c
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff764963479a ("drivers: phy: add generic PHY framework")
Cc: stable@vger.kernel.org
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-1-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2d633cb1421e679b56f1a9fe1f42f089706f1ed upstream.
For macro for_each_child_of_node(parent, child), refcount of @child has
been increased before entering its loop body, so normally needs to call
of_node_put(@child) before returning from the loop body to avoid refcount
leakage.
of_phy_provider_lookup() has such usage but does not call of_node_put()
before returning, so cause leakage of the OF node refcount.
Fix by simply calling of_node_put() before returning from the loop body.
The APIs affected by this issue are shown below since they indirectly
invoke problematic of_phy_provider_lookup().
phy_get()
of_phy_get()
devm_phy_get()
devm_of_phy_get()
devm_of_phy_get_by_index()
Fixes: 2a4c37016ca9 ("phy: core: Fix of_phy_provider_lookup to return PHY provider for sub node")
Cc: stable@vger.kernel.org
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-5-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ebdc6be16c2000e37fcb8b4072d442d268ad492 upstream.
_of_phy_get() will directly return when suffers of_device_is_compatible()
error, but it forgets to decrease refcount of OF node @args.np before error
return, the refcount was increased by previous of_parse_phandle_with_args()
so causes the OF node's refcount leakage.
Fix by decreasing the refcount via of_node_put() before the error return.
Fixes: b7563e2796f8 ("phy: work around 'phys' references to usb-nop-xceiv devices")
Cc: stable@vger.kernel.org
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-4-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
