commit 2a93c6cbd5a703d44c414a3c3945a87ce11430ba upstream.
Commit 'e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable
the domain")' aimed to make sure that a power-domain that is being
enabled without any particular performance-state requested will at least
turn the rail on, to avoid filling DeviceTree with otherwise unnecessary
required-opps properties.
But in the event that aggregation happens on a disabled power-domain, with
an enabled peer without performance-state, both the local and peer
corner are 0. The peer's enabled_corner is not considered, with the
result that the underlying (shared) resource is disabled.
One case where this can be observed is when the display stack keeps mmcx
enabled (but without a particular performance-state vote) in order to
access registers and sync_state happens in the rpmhpd driver. As mmcx_ao
is flushed the state of the peer (mmcx) is not considered and mmcx_ao
ends up turning off "mmcx.lvl" underneath mmcx. This has been observed
several times, but has been painted over in DeviceTree by adding an
explicit vote for the lowest non-disabled performance-state.
Fixes: e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable the domain")
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/linux-arm-msm/ZdMwZa98L23mu3u6@hovoldconsulting.com/
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240226-rpmhpd-enable-corner-fix-v1-1-68c004cec48c@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e9f25a290ae0016353c9ea13314c95fb3207812 upstream.
Each time SD/mmc phy is initialized, at times, in some of
the attempts, phy fails to completes its initialization
which results into timeout error. Per the HW spec, it is
a pre-requisite to ensure a stable SD clock before a phy
initialization is attempted.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222200930.1277665-1-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09e23823ae9a3e2d5d20f2e1efe0d6e48cef9129 upstream.
AC5X spec says PHY init complete bit must be polled until zero.
We see cases in which timeout can take longer than the standard
calculation on AC5X, which is expected following the spec comment above.
According to the spec, we must wait as long as it takes for that bit to
toggle on AC5X.
Cap that with 100 delay loops so we won't get stuck forever.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222191714.1216470-3-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff3206d2186d84e4f77e1378ba1d225633f17b9b upstream.
Initializing an eMMC that's connected via a 1-bit bus is current failing,
if the HW (DT) informs that 4-bit bus is supported. In fact this is a
regression, as we were earlier capable of falling back to 1-bit mode, when
switching to 4/8-bit bus failed. Therefore, let's restore the behaviour.
Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin)
Before patch:
[134509.044225] mmc0: switch to bus width 4 failed
[134509.044509] mmc0: new high speed MMC card at address 0001
[134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134509.281602] mmc0: switch to bus width 4 failed
[134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284609] ldm_validate_partition_table(): Disk read failed.
[134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289553] mmcblk0: unable to read partition table
[134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
[134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read
After patch:
[134551.089613] mmc0: switch to bus width 4 failed
[134551.090377] mmc0: new high speed MMC card at address 0001
[134551.102271] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134551.113365] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21
[134551.114262] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134551.114925] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
Fixes: 577fb13199b1 ("mmc: rework selection of bus speed mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Semenov <ivan@semenov.dev>
Link: https://lore.kernel.org/r/20240206172845.34316-1-ivan@semenov.dev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87a39071e0b639f45e05d296cc0538eef44ec0bd upstream.
Initialize the qDMA irqs after the registers are configured so that
interrupts that may have been pending from a primary kernel don't get
processed by the irq handler before it is ready to and cause panic with
the following trace:
Call trace:
fsl_qdma_queue_handler+0xf8/0x3e8
__handle_irq_event_percpu+0x78/0x2b0
handle_irq_event_percpu+0x1c/0x68
handle_irq_event+0x44/0x78
handle_fasteoi_irq+0xc8/0x178
generic_handle_irq+0x24/0x38
__handle_domain_irq+0x90/0x100
gic_handle_irq+0x5c/0xb8
el1_irq+0xb8/0x180
_raw_spin_unlock_irqrestore+0x14/0x40
__setup_irq+0x4bc/0x798
request_threaded_irq+0xd8/0x190
devm_request_threaded_irq+0x74/0xe8
fsl_qdma_probe+0x4d4/0xca8
platform_drv_probe+0x50/0xa0
really_probe+0xe0/0x3f8
driver_probe_device+0x64/0x130
device_driver_attach+0x6c/0x78
__driver_attach+0xbc/0x158
bus_for_each_dev+0x5c/0x98
driver_attach+0x20/0x28
bus_add_driver+0x158/0x220
driver_register+0x60/0x110
__platform_driver_register+0x44/0x50
fsl_qdma_driver_init+0x18/0x20
do_one_initcall+0x48/0x258
kernel_init_freeable+0x1a4/0x23c
kernel_init+0x10/0xf8
ret_from_fork+0x10/0x18
Cc: stable@vger.kernel.org
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Signed-off-by: Yi Zhao <yi.zhao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201220406.440145-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d739bccf261dd93ec1babf82f5c5d71dd4caa3e upstream.
There is chip (ls1028a) errata:
The SoC may hang on 16 byte unaligned read transactions by QDMA.
Unaligned read transactions initiated by QDMA may stall in the NOC
(Network On-Chip), causing a deadlock condition. Stalled transactions will
trigger completion timeouts in PCIe controller.
Workaround:
Enable prefetch by setting the source descriptor prefetchable bit
( SD[PF] = 1 ).
Implement this workaround.
Cc: stable@vger.kernel.org
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201215007.439503-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9845664b9ee47ce7ee7ea93caf47d39a9d4552c4 upstream.
There's a syzbot report that device name buffers passed to device
replace are not properly checked for string termination which could lead
to a read out of bounds in getname_kernel().
Add a helper that validates both source and target device name buffers.
For devid as the source initialize the buffer to empty string in case
something tries to read it later.
This was originally analyzed and fixed in a different way by Edward Adam
Davis (see links).
Link: https://lore.kernel.org/linux-btrfs/000000000000d1a1d1060cc9c5e7@google.com/
Link: https://lore.kernel.org/linux-btrfs/tencent_44CA0665C9836EF9EEC80CB9E7E206DF5206@qq.com/
CC: stable@vger.kernel.org # 4.19+
CC: Edward Adam Davis <eadavis@qq.com>
Reported-and-tested-by: syzbot+33f23b49ac24f986c9e8@syzkaller.appspotmail.com
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78c1375339a291cba492a70eaf12ec501d28a8e upstream.
It's currently possible to change the mesh ID when the
interface isn't yet in mesh mode, at the same time as
changing it into mesh mode. This leads to an overwrite
of data in the wdev->u union for the interface type it
currently has, causing cfg80211_change_iface() to do
wrong things when switching.
We could probably allow setting an interface to mesh
while setting the mesh ID at the same time by doing a
different order of operations here, but realistically
there's no userspace that's going to do this, so just
disallow changes in iftype when setting mesh ID.
Cc: stable@vger.kernel.org
Fixes: 29cbe68c516a ("cfg80211/mac80211: add mesh join/leave commands")
Reported-by: syzbot+dd4779978217b1973180@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f03fc340cac9ea1dc63cbf8c93dd2eb0f227815 upstream.
Since tomoyo_write_control() updates head->write_buf when write()
of long lines is requested, we need to fetch head->write_buf after
head->io_sem is held. Otherwise, concurrent write() requests can
cause use-after-free-write and double-free problems.
Reported-by: Sam Sun <samsun1006219@gmail.com>
Closes: https://lkml.kernel.org/r/CAEkJfYNDspuGxYx5kym8Lvp--D36CMDUErg4rxfWFJuPbbji8g@mail.gmail.com
Fixes: bd03a3e4c9a9 ("TOMOYO: Add policy namespace support.")
Cc: <stable@vger.kernel.org> # Linux 3.1+
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a11dd49dcb9376776193e15641f84fcc1e5980c9 ]
Offset vmemmap so that the first page of vmemmap will be mapped
to the first page of physical memory in order to ensure that
vmemmap’s bounds will be respected during
pfn_to_page()/page_to_pfn() operations.
The conversion macros will produce correct SV39/48/57 addresses
for every possible/valid DRAM_BASE inside the physical memory limits.
v2:Address Alex's comments
Suggested-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Dimitris Vlachos <dvlachos@ics.forth.gr>
Reported-by: Dimitris Vlachos <dvlachos@ics.forth.gr>
Closes: https://lore.kernel.org/linux-riscv/20240202135030.42265-1-csd4492@csd.uoc.gr
Fixes: d95f1a542c3d ("RISC-V: Implement sparsemem")
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240229191723.32779-1-dvlachos@ics.forth.gr
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f7a07646655fb4108da527565dcdc80124b14c4 ]
If a directory has a block with only ".__afsXXXX" files in it (from
uncompleted silly-rename), these .__afsXXXX files are skipped but without
advancing the file position in the dir_context. This leads to
afs_dir_iterate() repeating the block again and again.
Fix this by making the code that skips the .__afsXXXX file also manually
advance the file position.
The symptoms are a soft lookup:
watchdog: BUG: soft lockup - CPU#3 stuck for 52s! [check:5737]
...
RIP: 0010:afs_dir_iterate_block+0x39/0x1fd
...
? watchdog_timer_fn+0x1a6/0x213
...
? asm_sysvec_apic_timer_interrupt+0x16/0x20
? afs_dir_iterate_block+0x39/0x1fd
afs_dir_iterate+0x10a/0x148
afs_readdir+0x30/0x4a
iterate_dir+0x93/0xd3
__do_sys_getdents64+0x6b/0xd4
This is almost certainly the actual fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=218496
Fixes: 57e9d49c5452 ("afs: Hide silly-rename files from userspace")
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/786185.1708694102@warthog.procyon.org.uk
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4df49712eb54141be00a9312547436d55677f092 ]
We forgot to remove the line for snd-rtctimer from Makefile while
dropping the functionality. Get rid of the stale line.
Fixes: 34ce71a96dcb ("ALSA: timer: remove legacy rtctimer")
Link: https://lore.kernel.org/r/20240221092156.28695-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2df70149e73e79783bcbc7db4fa51ecef0e2022c ]
The bq27xxx i2c-client may not have an IRQ, in which case
client->irq will be 0. bq27xxx_battery_i2c_probe() already has
an if (client->irq) check wrapping the request_threaded_irq().
But bq27xxx_battery_i2c_remove() unconditionally calls
free_irq(client->irq) leading to:
[ 190.310742] ------------[ cut here ]------------
[ 190.310843] Trying to free already-free IRQ 0
[ 190.310861] WARNING: CPU: 2 PID: 1304 at kernel/irq/manage.c:1893 free_irq+0x1b8/0x310
Followed by a backtrace when unbinding the driver. Add
an if (client->irq) to bq27xxx_battery_i2c_remove() mirroring
probe() to fix this.
Fixes: 444ff00734f3 ("power: supply: bq27xxx: Fix I2C IRQ race on remove")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240215155133.70537-1-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fccfa646ef3628097d59f7d9c1a3e84d4b6bb45e ]
gcc-14 notices that the allocation with sizeof(void) on 32-bit architectures
is not enough for a 64-bit phys_addr_t:
drivers/firmware/efi/capsule-loader.c: In function 'efi_capsule_open':
drivers/firmware/efi/capsule-loader.c:295:24: error: allocation of insufficient size '4' for type 'phys_addr_t' {aka 'long long unsigned int'} with size '8' [-Werror=alloc-size]
295 | cap_info->phys = kzalloc(sizeof(void *), GFP_KERNEL);
| ^
Use the correct type instead here.
Fixes: f24c4d478013 ("efi/capsule-loader: Reinstate virtual capsule mapping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 743ad091fb46e622f1b690385bb15e3cd3daf874 ]
In the commit d73ef2d69c0d ("rtnetlink: let rtnl_bridge_setlink checks
IFLA_BRIDGE_MODE length"), an adjustment was made to the old loop logic
in the function `rtnl_bridge_setlink` to enable the loop to also check
the length of the IFLA_BRIDGE_MODE attribute. However, this adjustment
removed the `break` statement and led to an error logic of the flags
writing back at the end of this function.
if (have_flags)
memcpy(nla_data(attr), &flags, sizeof(flags));
// attr should point to IFLA_BRIDGE_FLAGS NLA !!!
Before the mentioned commit, the `attr` is granted to be IFLA_BRIDGE_FLAGS.
However, this is not necessarily true fow now as the updated loop will let
the attr point to the last NLA, even an invalid NLA which could cause
overflow writes.
This patch introduces a new variable `br_flag` to save the NLA pointer
that points to IFLA_BRIDGE_FLAGS and uses it to resolve the mentioned
error logic.
Fixes: d73ef2d69c0d ("rtnetlink: let rtnl_bridge_setlink checks IFLA_BRIDGE_MODE length")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20240227121128.608110-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e0f122c65912740327e4c54472acaa5f85868cb ]
Commit d0009effa886 ("netfilter: nf_tables: validate NFPROTO_* family") added
some validation of NFPROTO_* families in the nft_compat module, but it broke
the ability to use legacy iptables modules in dual-stack nftables.
While with legacy iptables one had to independently manage IPv4 and IPv6
tables, with nftables it is possible to have dual-stack tables sharing the
rules. Moreover, it was possible to use rules based on legacy iptables
match/target modules in dual-stack nftables.
As an example, the program from [2] creates an INET dual-stack family table
using an xt_bpf based rule, which looks like the following (the actual output
was generated with a patched nft tool as the current nft tool does not parse
dual stack tables with legacy match rules, so consider it for illustrative
purposes only):
table inet testfw {
chain input {
type filter hook prerouting priority filter; policy accept;
bytecode counter packets 0 bytes 0 accept
}
}
After d0009effa886 ("netfilter: nf_tables: validate NFPROTO_* family") we get
EOPNOTSUPP for the above program.
Fix this by allowing NFPROTO_INET for nft_(match/target)_validate(), but also
restrict the functions to classic iptables hooks.
Changes in v3:
* clarify that upstream nft will not display such configuration properly and
that the output was generated with a patched nft tool
* remove example program from commit description and link to it instead
* no code changes otherwise
Changes in v2:
* restrict nft_(match/target)_validate() to classic iptables hooks
* rewrite example program to use unmodified libnftnl
Fixes: d0009effa886 ("netfilter: nf_tables: validate NFPROTO_* family")
Link: https://lore.kernel.org/all/Zc1PfoWN38UuFJRI@calendula/T/#mc947262582c90fec044c7a3398cc92fac7afea72 [1]
Link: https://lore.kernel.org/all/20240220145509.53357-1-ignat@cloudflare.com/ [2]
Reported-by: Jordan Griege <jgriege@cloudflare.com>
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4b019515f950b4e6e5b74b2e1bb03a90cb33039 ]
Right now Linux BT stack cannot pass test case "GAP/CONN/CPUP/BV-05-C
'Connection Parameter Update Procedure Invalid Parameters Central
Responder'" in Bluetooth Test Suite revision GAP.TS.p44. [0]
That was revoled by commit c49a8682fc5d ("Bluetooth: validate BLE
connection interval updates"), but later got reverted due to devices
like keyboards and mice may require low connection interval.
So only validate the max value connection interval to pass the Test
Suite, and let devices to request low connection interval if needed.
[0] https://www.bluetooth.org/docman/handlers/DownloadDoc.ashx?doc_id=229869
Fixes: 68d19d7d9957 ("Revert "Bluetooth: validate BLE connection interval updates"")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e74aa53a68bf60f6019bd5d9a9a1406ec4d4865 ]
If we received HCI_EV_IO_CAPA_REQUEST while
HCI_OP_READ_REMOTE_EXT_FEATURES is yet to be responded assume the remote
does support SSP since otherwise this event shouldn't be generated.
Link: https://lore.kernel.org/linux-bluetooth/CABBYNZ+9UdG1cMZVmdtN3U2aS16AKMCyTARZZyFX7xTEDWcMOw@mail.gmail.com/T/#t
Fixes: c7f59461f5a7 ("Bluetooth: Fix a refcnt underflow problem for hci_conn")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61a5ab72edea7ebc3ad2c6beea29d966f528ebfb ]
hci_store_wake_reason() wrongly parses event HCI_Connection_Request
as HCI_Connection_Complete and HCI_Connection_Complete as
HCI_Connection_Request, so causes recording wakeup BD_ADDR error and
potential stability issue, fix it by using the correct field.
Fixes: 2f20216c1d6f ("Bluetooth: Emit controller suspend and resume events")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2449007d3f73b2842c9734f45f0aadb522daf592 ]
While handling the HCI_EV_HARDWARE_ERROR event, if the underlying
BT controller is not responding, the GPIO reset mechanism would
free the hci_dev and lead to a use-after-free in hci_error_reset.
Here's the call trace observed on a ChromeOS device with Intel AX201:
queue_work_on+0x3e/0x6c
__hci_cmd_sync_sk+0x2ee/0x4c0 [bluetooth <HASH:3b4a6>]
? init_wait_entry+0x31/0x31
__hci_cmd_sync+0x16/0x20 [bluetooth <HASH:3b4a 6>]
hci_error_reset+0x4f/0xa4 [bluetooth <HASH:3b4a 6>]
process_one_work+0x1d8/0x33f
worker_thread+0x21b/0x373
kthread+0x13a/0x152
? pr_cont_work+0x54/0x54
? kthread_blkcg+0x31/0x31
ret_from_fork+0x1f/0x30
This patch holds the reference count on the hci_dev while processing
a HCI_EV_HARDWARE_ERROR event to avoid potential crash.
Fixes: c7741d16a57c ("Bluetooth: Perform a power cycle when receiving hardware error event")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68b2c9eba38ec3f60f4894b189090febf4d8d22 ]
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863fa5 ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e67899abfbfdea0c3c0ed3fd263ffc601c5c157 ]
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c87 ("lan78xx: Set ASD in MAC_CR when EEE is enabled.")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10bfd453da64a057bcfd1a49fb6b271c48653cdb ]
It seems that if userspace provides a correct IFA_TARGET_NETNSID value
but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr()
returns -EINVAL with an elevated "struct net" refcount.
Fixes: 6ecf4c37eb3e ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a770cdc4382b457ca3d43d03f0f0064f905a0d0 ]
When a queue(tfile) is detached, we only update tfile's queue_index,
but do not update xdp_rxq_info's queue_index. This patch fixes it.
Fixes: 8bf5c4ee1889 ("tun: setup xdp_rxq_info")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Link: https://lore.kernel.org/r/1708398727-46308-1-git-send-email-wangyunjian@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ae1e9922bbdbaeb9cfbe91085ab75927488ac0f ]
syzkaller triggered following kasan splat:
BUG: KASAN: use-after-free in __skb_flow_dissect+0x19d1/0x7a50 net/core/flow_dissector.c:1170
Read of size 1 at addr ffff88812fb4000e by task syz-executor183/5191
[..]
kasan_report+0xda/0x110 mm/kasan/report.c:588
__skb_flow_dissect+0x19d1/0x7a50 net/core/flow_dissector.c:1170
skb_flow_dissect_flow_keys include/linux/skbuff.h:1514 [inline]
___skb_get_hash net/core/flow_dissector.c:1791 [inline]
__skb_get_hash+0xc7/0x540 net/core/flow_dissector.c:1856
skb_get_hash include/linux/skbuff.h:1556 [inline]
ip_tunnel_xmit+0x1855/0x33c0 net/ipv4/ip_tunnel.c:748
ipip_tunnel_xmit+0x3cc/0x4e0 net/ipv4/ipip.c:308
__netdev_start_xmit include/linux/netdevice.h:4940 [inline]
netdev_start_xmit include/linux/netdevice.h:4954 [inline]
xmit_one net/core/dev.c:3548 [inline]
dev_hard_start_xmit+0x13d/0x6d0 net/core/dev.c:3564
__dev_queue_xmit+0x7c1/0x3d60 net/core/dev.c:4349
dev_queue_xmit include/linux/netdevice.h:3134 [inline]
neigh_connected_output+0x42c/0x5d0 net/core/neighbour.c:1592
...
ip_finish_output2+0x833/0x2550 net/ipv4/ip_output.c:235
ip_finish_output+0x31/0x310 net/ipv4/ip_output.c:323
..
iptunnel_xmit+0x5b4/0x9b0 net/ipv4/ip_tunnel_core.c:82
ip_tunnel_xmit+0x1dbc/0x33c0 net/ipv4/ip_tunnel.c:831
ipgre_xmit+0x4a1/0x980 net/ipv4/ip_gre.c:665
__netdev_start_xmit include/linux/netdevice.h:4940 [inline]
netdev_start_xmit include/linux/netdevice.h:4954 [inline]
xmit_one net/core/dev.c:3548 [inline]
dev_hard_start_xmit+0x13d/0x6d0 net/core/dev.c:3564
...
The splat occurs because skb->data points past skb->head allocated area.
This is because neigh layer does:
__skb_pull(skb, skb_network_offset(skb));
... but skb_network_offset() returns a negative offset and __skb_pull()
arg is unsigned. IOW, we skb->data gets "adjusted" by a huge value.
The negative value is returned because skb->head and skb->data distance is
more than 64k and skb->network_header (u16) has wrapped around.
The bug is in the ip_tunnel infrastructure, which can cause
dev->needed_headroom to increment ad infinitum.
The syzkaller reproducer consists of packets getting routed via a gre
tunnel, and route of gre encapsulated packets pointing at another (ipip)
tunnel. The ipip encapsulation finds gre0 as next output device.
This results in the following pattern:
1). First packet is to be sent out via gre0.
Route lookup found an output device, ipip0.
2).
ip_tunnel_xmit for gre0 bumps gre0->needed_headroom based on the future
output device, rt.dev->needed_headroom (ipip0).
3).
ip output / start_xmit moves skb on to ipip0. which runs the same
code path again (xmit recursion).
4).
Routing step for the post-gre0-encap packet finds gre0 as output device
to use for ipip0 encapsulated packet.
tunl0->needed_headroom is then incremented based on the (already bumped)
gre0 device headroom.
This repeats for every future packet:
gre0->needed_headroom gets inflated because previous packets' ipip0 step
incremented rt->dev (gre0) headroom, and ipip0 incremented because gre0
needed_headroom was increased.
For each subsequent packet, gre/ipip0->needed_headroom grows until
post-expand-head reallocations result in a skb->head/data distance of
more than 64k.
Once that happens, skb->network_header (u16) wraps around when
pskb_expand_head tries to make sure that skb_network_offset() is unchanged
after the headroom expansion/reallocation.
After this skb_network_offset(skb) returns a different (and negative)
result post headroom expansion.
The next trip to neigh layer (or anything else that would __skb_pull the
network header) makes skb->data point to a memory location outside
skb->head area.
v2: Cap the needed_headroom update to an arbitarily chosen upperlimit to
prevent perpetual increase instead of dropping the headroom increment
completely.
Reported-and-tested-by: syzbot+bfde3bef047a81b8fde6@syzkaller.appspotmail.com
Closes: https://groups.google.com/g/syzkaller-bugs/c/fL9G6GtWskY/m/VKk_PR5FBAAJ
Fixes: 243aad830e8a ("ip_gre: include route header_len in max_headroom calculation")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220135606.4939-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 469b992489852b500d39048aa0013639dfe9f2e6 ]
The relevant changes to the already existing GD5F1GQ4UExxG support has
been determined by consulting the GigaDevice product change notice
AN-0392-10, version 1.0 from November 30, 2020.
As the overlaps are huge, variable names have been generalized
accordingly.
Apart from the lowered ECC strength (4 instead of 8 bits per 512 bytes),
the new device ID, and the extra quad IO dummy byte, no changes had to
be taken into account.
New hardware features are not supported, namely:
- Power on reset
- Unique ID
- Double transfer rate (DTR)
- Parameter page
- Random data quad IO
The inverted semantic of the "driver strength" register bits, defaulting
to 100% instead of 50% for the Q5 devices, got ignored as the driver has
never touched them anyway.
The no longer supported "read from cache during block erase"
functionality is not reflected as the current SPI NAND core does not
support it anyway.
Implementation has been tested on MediaTek MT7688 based GARDENA smart
Gateways using both, GigaDevice GD5F1GQ5UEYIG and GD5F1GQ4UBYIG.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210211113619.3502-1-code@reto-schneider.ch
Stable-dep-of: 59950610c0c0 ("mtd: spinand: gigadevice: Fix the get ecc status issue")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbcbfd662a725641d118fb3ae5ffb7be4e3d0fb0 ]
On some devices the ACPI name of the touchscreen is e.g. either
MSSL1680:00 or MSSL1680:01 depending on the BIOS version.
This happens for example on the "Chuwi Hi8 Air" tablet where the initial
commit's ts_data uses "MSSL1680:00" but the tablets from the github issue
and linux-hardware.org probe linked below both use "MSSL1680:01".
Replace the strcmp() match on ts_data->acpi_name with a strstarts()
check to allow using a partial match on just the ACPI HID of "MSSL1680"
and change the ts_data->acpi_name for the "Chuwi Hi8 Air" accordingly
to fix the touchscreen not working on models where it is "MSSL1680:01".
Note this drops the length check for I2C_NAME_SIZE. This never was
necessary since the ACPI names used are never more then 11 chars and
I2C_NAME_SIZE is 20 so the replaced strncmp() would always stop long
before reaching I2C_NAME_SIZE.
Link: https://linux-hardware.org/?computer=AC4301C0542A
Fixes: bbb97d728f77 ("platform/x86: touchscreen_dmi: Add info for the Chuwi Hi8 Air tablet")
Closes: https://github.com/onitake/gsl-firmware/issues/91
Cc: stable@vger.kernel.org
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240212120608.30469-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c9b528c35795b711331ed36dc3dbee90d5812d4e upstream.
This mostly reverts commit 6bd97bf273bd ("ext4: remove redundant
mb_regenerate_buddy()") and reintroduces mb_regenerate_buddy(). Based on
code in mb_free_blocks(), fast commit replay can end up marking as free
blocks that are already marked as such. This causes corruption of the
buddy bitmap so we need to regenerate it in that case.
Reported-by: Jan Kara <jack@suse.cz>
Fixes: 6bd97bf273bd ("ext4: remove redundant mb_regenerate_buddy()")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240104142040.2835097-4-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b820de741ae48ccf50dd95e297889c286ff4f760 upstream.
If kiocb_set_cancel_fn() is called for I/O submitted via io_uring, the
following kernel warning appears:
WARNING: CPU: 3 PID: 368 at fs/aio.c:598 kiocb_set_cancel_fn+0x9c/0xa8
Call trace:
kiocb_set_cancel_fn+0x9c/0xa8
ffs_epfile_read_iter+0x144/0x1d0
io_read+0x19c/0x498
io_issue_sqe+0x118/0x27c
io_submit_sqes+0x25c/0x5fc
__arm64_sys_io_uring_enter+0x104/0xab0
invoke_syscall+0x58/0x11c
el0_svc_common+0xb4/0xf4
do_el0_svc+0x2c/0xb0
el0_svc+0x2c/0xa4
el0t_64_sync_handler+0x68/0xb4
el0t_64_sync+0x1a4/0x1a8
Fix this by setting the IOCB_AIO_RW flag for read and write I/O that is
submitted by libaio.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Sandeep Dhavale <dhavale@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240215204739.2677806-2-bvanassche@acm.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d28e4dff085c5a87025c9a0a85fb798bd8e9ca17 upstream.
As it turns out, my earlier patch in commit 86d46fdaa12a (block:
ataflop: fix breakage introduced at blk-mq refactoring) was
incomplete. This patch fixes any remaining issues found during
more testing and code review.
Requests exceeding 4 k are handled in 4k segments but
__blk_mq_end_request() is never called on these (still
sectors outstanding on the request). With redo_fd_request()
removed, there is no provision to kick off processing of the
next segment, causing requests exceeding 4k to hang. (By
setting /sys/block/fd0/queue/max_sectors_k <= 4 as workaround,
this behaviour can be avoided).
Instead of reintroducing redo_fd_request(), requeue the remainder
of the request by calling blk_mq_requeue_request() on incomplete
requests (i.e. when blk_update_request() still returns true), and
rely on the block layer to queue the residual as new request.
Both error handling and formatting needs to release the
ST-DMA lock, so call finish_fdc() on these (this was previously
handled by redo_fd_request()). finish_fdc() may be called
legitimately without the ST-DMA lock held - make sure we only
release the lock if we actually held it. In a similar way,
early exit due to errors in ataflop_queue_rq() must release
the lock.
After minor errors, fd_error sets up to recalibrate the drive
but never re-runs the current operation (another task handled by
redo_fd_request() before). Call do_fd_action() to get the next
steps (seek, retry read/write) underway.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Fixes: 6ec3938cff95f (ataflop: convert to blk-mq)
CC: linux-block@vger.kernel.org
Link: https://lore.kernel.org/r/20211024002013.9332-1-schmitzmic@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[MSch: v5.10 backport merge conflict fix]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c43177ffb54ea5be97505eb8e2690e99ac96bc9 ]
When waiting for a syncobj timeline point whose fence has not yet been
submitted with the WAIT_FOR_SUBMIT flag, a callback is registered using
drm_syncobj_fence_add_wait and the thread is put to sleep until the
timeout expires. If the fence is submitted before then,
drm_syncobj_add_point will wake up the sleeping thread immediately which
will proceed to wait for the fence to be signaled.
However, if the WAIT_AVAILABLE flag is used instead,
drm_syncobj_fence_add_wait won't get called, meaning the waiting thread
will always sleep for the full timeout duration, even if the fence gets
submitted earlier. If it turns out that the fence *has* been submitted
by the time it eventually wakes up, it will still indicate to userspace
that the wait completed successfully (it won't return -ETIME), but it
will have taken much longer than it should have.
To fix this, we must call drm_syncobj_fence_add_wait if *either* the
WAIT_FOR_SUBMIT flag or the WAIT_AVAILABLE flag is set. The only
difference being that with WAIT_FOR_SUBMIT we will also wait for the
fence to be signaled after it has been submitted while with
WAIT_AVAILABLE we will return immediately.
IGT test patch: https://lists.freedesktop.org/archives/igt-dev/2024-January/067537.html
v1 -> v2: adjust lockdep_assert_none_held_once condition
(cherry picked from commit 8c44ea81634a4a337df70a32621a5f3791be23df)
Fixes: 01d6c3578379 ("drm/syncobj: add support for timeline point wait v8")
Signed-off-by: Erik Kurzinger <ekurzinger@nvidia.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20240119163208.3723457-1-ekurzinger@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7621350c6bb20fb6ab7eb988833ab96eac3dcbef ]
DRM_SYNCOBJ_WAIT_FLAGS_WAIT_FOR_SUBMIT can't be used when we hold locks
since we are basically waiting for userspace to do something.
Holding a lock while doing so can trivial deadlock with page faults
etc...
So make lockdep complain when a driver tries to do this.
v2: Add lockdep_assert_none_held() macro.
v3: Add might_sleep() and also use lockdep_assert_none_held() in the
IOCTL path.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patchwork.freedesktop.org/patch/414944/
Stable-dep-of: 3c43177ffb54 ("drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bccebf64701735533c8db37773eeacc6566cc8ec ]
We need to set the dormant flag again if we fail to register
the hooks.
During memory pressure hook registration can fail and we end up
with a table marked as active but no registered hooks.
On table/base chain deletion, nf_tables will attempt to unregister
the hook again which yields a warn splat from the nftables core.
Reported-and-tested-by: syzbot+de4025c006ec68ac56fc@syzkaller.appspotmail.com
Fixes: 179d9ba5559a ("netfilter: nf_tables: fix table flag updates")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdfbaec5923d9359698cbb286bc0deadbb717504 ]
If we have a non-DATA record on the rx_list and another record of the
same type still on the queue, we will end up merging them:
- process_rx_list copies the non-DATA record
- we start the loop and process the first available record since it's
of the same type
- we break out of the loop since the record was not DATA
Just check the record type and jump to the end in case process_rx_list
did some work.
Fixes: 692d7b5d1f91 ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/bd31449e43bd4b6ff546f5c51cf958c31c511deb.1708007371.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5123edd10cf9d324fcb88e276bdc7375f3c5321 ]
Pointless else branch after goto makes the code harder to refactor
down the line.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fdfbaec5923d ("tls: stop recv() if initial process_rx_list gave us non-DATA")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfc06e1aaa130b86a81ce3c41ec71a2f5e191690 ]
'recv_end:' checks num_async and decrypted, and is then followed
by the 'end' label. Since we know that decrypted and num_async
are 0 at the start we can jump to 'end'.
Move the init of decrypted and num_async to let the compiler
catch if I'm wrong.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fdfbaec5923d ("tls: stop recv() if initial process_rx_list gave us non-DATA")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 723a2cc8d69d4342b47dfddbfe6c19f1b135f09b ]
The signature for __iowrite64_copy() requires the number of 64 bit
quantities, not bytes. Multiple by 8 to get to a byte length before
invoking zpci_memcpy_toio()
Fixes: 87bc359b9822 ("s390/pci: speed up __iowrite64_copy by using pci store block insn")
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/0-v1-9223d11a7662+1d7785-s390_iowrite64_jgg@nvidia.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5f0de6df6dce8d641ef58ef7012f3304dffb9a1 ]
One of the worst offenders of "fake flexible arrays" is struct sockaddr,
as it is the classic example of why GCC and Clang have been traditionally
forced to treat all trailing arrays as fake flexible arrays: in the
distant misty past, sa_data became too small, and code started just
treating it as a flexible array, even though it was fixed-size. The
special case by the compiler is specifically that sizeof(sa->sa_data)
and FORTIFY_SOURCE (which uses __builtin_object_size(sa->sa_data, 1))
do not agree (14 and -1 respectively), which makes FORTIFY_SOURCE treat
it as a flexible array.
However, the coming -fstrict-flex-arrays compiler flag will remove
these special cases so that FORTIFY_SOURCE can gain coverage over all
the trailing arrays in the kernel that are _not_ supposed to be treated
as a flexible array. To deal with this change, convert sa_data to a true
flexible array. To keep the structure size the same, move sa_data into
a union with a newly introduced sa_data_min with the original size. The
result is that FORTIFY_SOURCE can continue to have no idea how large
sa_data may actually be, but anything using sizeof(sa->sa_data) must
switch to sizeof(sa->sa_data_min).
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Dylan Yudaken <dylany@fb.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Petr Machata <petrm@nvidia.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: syzbot <syzkaller@googlegroups.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221018095503.never.671-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a7d6027790ac ("arp: Prevent overflow in arp_req_get().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5559cea2d5aa3018a5f00dd2aca3427ba09b386b ]
The pernet operations structure for the subsystem must be registered
before registering the generic netlink family.
Fixes: 915d7e5e5930 ("ipv6: sr: add code base for control plane support of SR-IPv6")
Signed-off-by: Vasiliy Kovalev <kovalev@altlinux.org>
Link: https://lore.kernel.org/r/20240215202717.29815-1-kovalev@altlinux.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ea38e2aeb72349cad50e38899b0ba6fbcb2af3d ]
The max length of volume->vid value is 20 characters.
So increase idbuf[] size up to 24 to avoid overflow.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
[DH: Actually, it's 20 + NUL, so increase it to 24 and use snprintf()]
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20240211150442.3416-1-d.dulov@aladdin.ru/ # v1
Link: https://lore.kernel.org/r/20240212083347.10742-1-d.dulov@aladdin.ru/ # v2
Link: https://lore.kernel.org/r/20240219143906.138346-3-dhowells@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e898e4cd1aab271ca414f9ac6e08e4c761f6913c ]
net->dev_base_seq and ipv6.dev_addr_genid are monotonically increasing.
If we XOR their values, we could miss to detect if both values
were changed with the same amount.
Fixes: 63998ac24f83 ("ipv6: provide addr and netconf dump consistency info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 081a0e3b0d4c061419d3f4679dec9f68725b17e4 ]
net->dev_base_seq and ipv4.dev_addr_genid are monotonically increasing.
If we XOR their values, we could miss to detect if both values
were changed with the same amount.
Fixes: 0465277f6b3f ("ipv4: provide addr and netconf dump consistency info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
