[ Upstream commit 9f538b415db862e74b8c5d3abbccfc1b2b6caa38 ]
Register value persist after booting the kernel using
kexec which results in kernel panic. Thus clear the
BM pool registers before initialisation to fix the issue.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Jenishkumar Maheshbhai Patel <jpatel2@marvell.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/20240119035914.2595665-1-jpatel2@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c6d5189246f590e4e1f167991558bdb72a4738b ]
When `in` allocated by kvzalloc fails, arfs_create_groups will free
ft->g and return an error. However, arfs_create_table, the only caller of
arfs_create_groups, will hold this error and call to
mlx5e_destroy_flow_table, in which the ft->g will be freed again.
Fixes: 1cabe6b0965e ("net/mlx5e: Create aRFS flow tables")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5665954293f13642f9c052ead83c1e9d8cff186f ]
When FW provides ICM addresses for drop RX/TX, the provided capability
is 64 bits that contain its GVMI as well as the ICM address itself.
In case of TX DROP this GVMI is different from the GVMI that the
domain is operating on.
This patch fixes the action to use these GVMI IDs, as provided by FW.
Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c1069fa42872f95cf3c6fedf80723d391e12d57 ]
The first message to firmware may fail if the device is undergoing FLR.
The driver has some recovery logic for this failure scenario but we must
wait 100 msec for FLR to complete before proceeding. Otherwise the
recovery will always fail.
Fixes: ba02629ff6cb ("bnxt_en: log firmware status on firmware init failure")
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240117234515.226944-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1311a8f0d4b23f58bbababa13623aa40b8ad4e0c upstream.
When mc146818_avoid_UIP() fails to return a valid value, this is because
UIP didn't clear in the timeout period. Adjust the return code in this
case to -ETIMEDOUT.
Tested-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: <stable@vger.kernel.org>
Fixes: cdedc45c579f ("rtc: cmos: avoid UIP when reading alarm time")
Fixes: cd17420ebea5 ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231128053653.101798-3-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84a6be7db9050dd2601c9870f65eab9a665d2d5d upstream.
There is no need to duplicate what SPI core or individual controller
drivers already do, i.e. mapping the buffers for DMA capable transfers.
Note, that the code, besides its redundancy, was buggy: strictly speaking
there is no guarantee, while it's true for those which can use this code
(see below), that the SPI host controller _is_ the device which does DMA.
Also see the Link tags below.
Additional notes. Currently only two SPI host controller drivers may use
premapped (by the user) DMA buffers:
- drivers/spi/spi-au1550.c
- drivers/spi/spi-fsl-spi.c
Both of them have DMA mapping support code. I don't expect that SPI host
controller code is worse than what has been done in mmc_spi. Hence I do
not expect any regressions here. Otherwise, I'm pretty much sure these
regressions have to be fixed in the respective drivers, and not here.
That said, remove all related pieces of DMA mapping code from mmc_spi.
Link: https://lore.kernel.org/linux-mmc/c73b9ba9-1699-2aff-e2fd-b4b4f292a3ca@raspberrypi.org/
Link: https://stackoverflow.com/questions/67620728/mmc-spi-issue-not-able-to-setup-mmc-sd-card-in-linux
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231207221901.3259962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d0c8d0aef6355660b6775d57ccd5d4ea2e15802 upstream.
Field Firmware Update (ffu) may use close-ended or open ended sequence.
Each such sequence is comprised of a write commands enclosed between 2
switch commands - to and from ffu mode. So for the close-ended case, it
will be: cmd6->cmd23-cmd25-cmd6.
Some host controllers however, get confused when multi-block rw is sent
without sbc, and may generate auto-cmd12 which breaks the ffu sequence.
I encountered this issue while testing fwupd (github.com/fwupd/fwupd)
on HP Chromebook x2, a qualcomm based QC-7c, code name - strongbad.
Instead of a quirk, or hooking the request function of the msm ops,
it would be better to fix the ioctl handling and make it use mrq.sbc
instead of issuing SET_BLOCK_COUNT separately.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231129092535.3278-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bd694ac2f682fb8017e16148b928482bc8fa4b upstream.
Ensure read and write locks for the channel are not taken in succession by
dropping the read lock from parse_xfer_event() such that a callback given
to client can potentially queue buffers and acquire the write lock in that
process. Any queueing of buffers should be done without channel read lock
acquired as it can result in multiple locks and a soft lockup.
Cc: <stable@vger.kernel.org> # 5.7
Fixes: 1d3173a3bae7 ("bus: mhi: core: Add support for processing events from client device")
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Tested-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1702276972-41296-3-git-send-email-quic_qianyu@quicinc.com
[mani: added fixes tag and cc'ed stable]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78aafb3884f6bc6636efcc1760c891c8500b9922 upstream.
There is a dead-lock in the hwrng device read path. This triggers
when the user reads from /dev/hwrng into memory also mmap-ed from
/dev/hwrng. The resulting page fault triggers a recursive read
which then dead-locks.
Fix this by using a stack buffer when calling copy_to_user.
Reported-by: Edward Adam Davis <eadavis@qq.com>
Reported-by: syzbot+c52ab18308964d248092@syzkaller.appspotmail.com
Fixes: 9996508b3353 ("hwrng: core - Replace u32 in driver API with byte array")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0080af84d3fb2423f0b3b55eff666f545eb097 upstream.
In order to avoid unnecessary pollution of the global symbol namespace
move the core/library functions into a specific namespace and import
that into the various specific device drivers that use them.
For more information see https://lwn.net/Articles/760045/
An alternative here would be to conclude that we are unlikely to see
support for the other ad7091r parts in the near future and just merge
the two modules into one supporting just the i2c -5 variant.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-3-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f5c24d94512f1b288262beda4d3dcb9629222fc7 ]
__dma_async_device_channel_register() can fail. In case of failure,
chan->local is freed (with free_percpu()), and chan->local is nullified.
When dma_async_device_unregister() is called (because of managed API or
intentionally by DMA controller driver), channels are unconditionally
unregistered, leading to this NULL pointer:
[ 1.318693] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
[...]
[ 1.484499] Call trace:
[ 1.486930] device_del+0x40/0x394
[ 1.490314] device_unregister+0x20/0x7c
[ 1.494220] __dma_async_device_channel_unregister+0x68/0xc0
Look at dma_async_device_register() function error path, channel device
unregistration is done only if chan->local is not NULL.
Then add the same condition at the beginning of
__dma_async_device_channel_unregister() function, to avoid NULL pointer
issue whatever the API used to reach this function.
Fixes: d2fb0a043838 ("dmaengine: break out channel registration")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20231213160452.2598073-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e71c5c89bcb165a02df35325aa13d1ee40112401 ]
The ADC needs a voltage reference to work correctly.
Users can provide an external voltage reference or use the chip internal
reference to operate the ADC.
The availability of an in chip reference for the ADC saves the user from
having to supply an external voltage reference, which makes the external
reference an optional property as described in the device tree
documentation.
Though, to use the internal reference, it must be enabled by writing to
the configuration register.
Enable AD7091R internal voltage reference if no external vref is supplied.
Fixes: 260442cc5be4 ("iio: adc: ad7091r5: Add scale and external VREF support")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/b865033fa6a4fc4bf2b4a98ec51a6144e0f64f77.1703013352.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020e71c7ffc25dfe29ed9be6c2d39af7bd7f661f ]
AD7091R-5 devices are supported by the ad7091r-5 driver together with
the ad7091r-base driver. Those drivers declared iio events for notifying
user space when ADC readings fall bellow the thresholds of low limit
registers or above the values set in high limit registers.
However, to configure iio events and their thresholds, a set of callback
functions must be implemented and those were not present until now.
The consequence of trying to configure ad7091r-5 events without the
proper callback functions was a null pointer dereference in the kernel
because the pointers to the callback functions were not set.
Implement event configuration callbacks allowing users to read/write
event thresholds and enable/disable event generation.
Since the event spec structs are generic to AD7091R devices, also move
those from the ad7091r-5 driver the base driver so they can be reused
when support for ad7091r-2/-4/-8 be added.
Fixes: ca69300173b6 ("iio: adc: Add support for AD7091R5 ADC")
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/59552d3548dabd56adc3107b7b4869afee2b0c3c.1703013352.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 149694f5e79b0c7a36ceb76e7c0d590db8f151c1 ]
The ad7091r-base driver sets up an interrupt handler for firing events
when inputs are either above or below a certain threshold.
However, for the interrupt signal to come from the device it must be
configured to enable the ALERT/BUSY/GPO pin to be used as ALERT, which
was not being done until now.
Enable interrupt signals on the ALERT/BUSY/GPO pin by setting the proper
bit in the configuration register.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/e8da2ee98d6df88318b14baf3dc9630e20218418.1702746240.git.marcelo.schmitt1@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 020e71c7ffc2 ("iio: adc: ad7091r: Allow users to configure device events")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d710b769c1f5f0d55c9ad9bb49b7dce009ec103 ]
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ef79cd1412236d884ab0c46b4d1921380807b48 ]
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e11c29873a8a296a20f99b3e03095e65ebf897d ]
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording]
Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com
Fixes: 43e6409db64d ("PCI: mediatek: Add MSI support for MT2712 and MT7622")
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40c304109e866a7dc123661a5c8ca72f6b5e14e0 ]
Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.
Data pattern likes below when sg enabled, package size is 1k and mult is 2
[UVC Header(8B) ] [data(3k - 8)] ...
The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
0xd000: wrong
0xe000: wrong
0xf000: correct
0x10000: wrong
0x11000: wrong
0x12000: correct
...
To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92f02efa1d86d7dcaef7f38a5fe3396c4e88a93c ]
ISO basic transfer is
ITP(SOF) Package_0 Package_1 ... Package_n
CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.
According USB spec defination:
Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)
Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.
Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-3-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2627335a1329a0d39d8d277994678571c4f21800 ]
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 92f02efa1d86 ("usb: cdns3: fix iso transfer error when mult is not zero")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b8be5ecff26201bafb0a554c74e91571299fb94 ]
When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.
cdns3_prepare_trb: ep2in: trb 0000000000ac755f, dma buf: 0xbf455000, size: 8, burst: 128 ctrl: 0x00000415 (C=1, T=0, ISP, CHAIN, Normal)
cdns3_prepare_trb: ep2in: trb 00000000a574e693, dma buf: 0xc0200fe0, size: 1016, burst: 128 ctrl: 0x00000405 (C=1, T=0, ISP, Normal)
But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.
The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.
Fixed it by below major steps:
1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.
.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB, LINK_TRB ... LINK_TRB
^End of TRB List
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fba8701baed76eac00b84b59f09f6a077f24c534 ]
Patch fixes the following warnings:
cdns3-gadget.c:1203: sparse: warning: incorrect type
in assignment (different base types)
cdns3-gadget.c:1203: sparse: expected restricted __le32 [usertype] length
cdns3-gadget.c:1203: sparse: got unsigned long
cdns3-gadget.c:1250: sparse: warning: invalid assignment: |=
cdns3-gadget.c:1250: sparse: left side has type restricted __le32
cdns3-gadget.c:1250: sparse: right side has type unsigned long
cdns3-gadget.c:1253: sparse: warning: invalid assignment: |=
cdns3-gadget.c:1253: sparse: left side has type restricted __le32
cdns3-gadget.c:1253: sparse: right side has type unsigned long
cdns3-ep0.c:367: sparse: warning: restricted __le16 degrades to integer
cdns3-ep0.c:792: sparse: warning: symbol 'cdns3_gadget_ep0_ops' was not
declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Stable-dep-of: 1b8be5ecff26 ("usb: cdns3: fix uvc failure work since sg support enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 990489e1042c6c5d6bccf56deca68f8dbeed8180 ]
To properly handle ACK on the bus when transferring more than one
message in polling mode, move the polling handling loop from
s3c24xx_i2c_message_start() to s3c24xx_i2c_doxfer(). This way
i2c_s3c_irq_nextbyte() is always executed till the end, properly
acknowledging the IRQ bits and no recursive calls to
i2c_s3c_irq_nextbyte() are made.
While touching this, also fix finishing transfers in polling mode by
using common code path and always waiting for the bus to become idle
and disabled.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9cf23ed55d7ba3ab26d617a3ae507863674c8f ]
To properly handle read transfers in polling mode, no waiting for the ACK
state is needed as it will never come. Just wait a bit to ensure start
state is on the bus and continue processing next bytes.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483ae90d8f976f8339cf81066312e1329f2d3706 ]
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Reported-by: Orel Hagag <orelh@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/2d91c89afba59c22587b444994ae419dbea8d876.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 194ab9476089bbfc021073214e071a404e375ee6 ]
Move the initialization and de-initialization code further below in
order to avoid forward declarations in the next patch. No functional
changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 483ae90d8f97 ("mlxsw: spectrum_acl_tcam: Fix stack corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61fe3b9102ac84ba479ab84d8f5454af2e21e468 ]
Move mutex_destroy() to the end to make the function symmetric with
mlxsw_sp_acl_tcam_init(). No functional changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 483ae90d8f97 ("mlxsw: spectrum_acl_tcam: Fix stack corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c087dfcc9d5e7e8557d217f01f58ba42d1ddbf1 ]
Use 'bitmap_zalloc()' to simplify code, improve the semantic and avoid
some open-coded arithmetic in allocator arguments.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 483ae90d8f97 ("mlxsw: spectrum_acl_tcam: Fix stack corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d6eeabcfaba2fcadf5443b575789ea606f9de83 ]
Lately, a bug was found when many TC filters are added - at some point,
several bugs are printed to dmesg [1] and the switch is crashed with
segmentation fault.
The issue starts when gen_pool_free() fails because of unexpected
behavior - a try to free memory which is already freed, this leads to BUG()
call which crashes the switch and makes many other bugs.
Trying to track down the unexpected behavior led to a bug in eRP code. The
function mlxsw_sp_acl_erp_table_alloc() gets a pointer to the allocated
index, sets the value and returns an error code. When gen_pool_alloc()
fails it returns address 0, we track it and return -ENOBUFS outside, BUT
the call for gen_pool_alloc() already override the index in erp_table
structure. This is a problem when such allocation is done as part of
table expansion. This is not a new table, which will not be used in case
of allocation failure. We try to expand eRP table and override the
current index (non-zero) with zero. Then, it leads to an unexpected
behavior when address 0 is freed twice. Note that address 0 is valid in
erp_table->base_index and indeed other tables use it.
gen_pool_alloc() fails in case that there is no space left in the
pre-allocated pool, in our case, the pool is limited to
ACL_MAX_ERPT_BANK_SIZE, which is read from hardware. When more than max
erp entries are required, we exceed the limit and return an error, this
error leads to "Failed to migrate vregion" print.
Fix this by changing erp_table->base_index only in case of a successful
allocation.
Add a test case for such a scenario. Without this fix it causes
segmentation fault:
$ TESTS="max_erp_entries_test" ./tc_flower.sh
./tc_flower.sh: line 988: 1560 Segmentation fault tc filter del dev $h2 ingress chain $i protocol ip pref $i handle $j flower &>/dev/null
[1]:
kernel BUG at lib/genalloc.c:508!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 3531 Comm: tc Not tainted 6.7.0-rc5-custom-ga6893f479f5e #1
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:gen_pool_free_owner+0xc9/0xe0
...
Call Trace:
<TASK>
__mlxsw_sp_acl_erp_table_other_dec+0x70/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_erp_mask_destroy+0xf5/0x110 [mlxsw_spectrum]
objagg_obj_root_destroy+0x18/0x80 [objagg]
objagg_obj_destroy+0x12c/0x130 [objagg]
mlxsw_sp_acl_erp_mask_put+0x37/0x50 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_region_entry_remove+0x74/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_entry_del+0x1e/0x40 [mlxsw_spectrum]
mlxsw_sp_acl_tcam_ventry_del+0x78/0xd0 [mlxsw_spectrum]
mlxsw_sp_flower_destroy+0x4d/0x70 [mlxsw_spectrum]
mlxsw_sp_flow_block_cb+0x73/0xb0 [mlxsw_spectrum]
tc_setup_cb_destroy+0xc1/0x180
fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
__fl_delete+0x1ac/0x1c0 [cls_flower]
fl_destroy+0xc2/0x150 [cls_flower]
tcf_proto_destroy+0x1a/0xa0
...
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
Fixes: f465261aa105 ("mlxsw: spectrum_acl: Implement common eRP core")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/4cfca254dfc0e5d283974801a24371c7b6db5989.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e327b2372bc0f18c30433ac40be07741b59231c5 ]
In ravb_start_xmit(), ravb driver uses u32 variable to store result of
dma_map_single() call. Since ravb hardware has 32-bit address fields in
descriptors, this works properly when mapping is successful - it is
platform's job to provide mapping addresses that fit into hardware
limitations.
However, in failure case dma_map_single() returns DMA_MAPPING_ERROR
constant that is 64-bit when dma_addr_t is 64-bit. Storing this constant
in u32 leads to truncation, and further call to dma_mapping_error()
fails to notice the error.
Fix that by storing result of dma_map_single() in a dma_addr_t
variable.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e398822c4751017fe401f57409488f5948d12fb5 ]
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64e47d8afb5ca533b27efc006405e5bcae2c4a7b ]
The value of AM65_CPSW_MAX_PACKET_SIZE represents the maximum length
of a received frame. This value is written to the register
AM65_CPSW_PORT_REG_RX_MAXLEN.
The maximum MTU configured on the network device should then leave
some room for the ethernet headers and frame check. Otherwise, if
the network interface is configured to its maximum mtu possible,
the frames will be larger than AM65_CPSW_MAX_PACKET_SIZE and will
get dropped as oversized.
The switch supports ethernet frame sizes between 64 and 2024 bytes
(including VLAN) as stated in the technical reference manual, so
define AM65_CPSW_MAX_PACKET_SIZE with that maximum size.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240105085530.14070-2-jorge.sanjuangarcia@duagon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12ca110c613a81cb0f0099019c839d078cd0f38 ]
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab47 ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a1abc24850eb759e36a2f8869161c3b7254c904 ]
The nvmet_tcp_handle_h2c_data_pdu() function should take into
consideration the possibility that the header digest and/or the data
digests are enabled when calculating the expected PDU length, before
comparing it to the value stored in cmd->pdu_len.
Fixes: efa56305908b ("nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0849a5441358cef02586fb2d60f707c0db195628 ]
in nvmet_tcp_handle_h2c_data_pdu(), if the host sends a data_offset
different from rbytes_done, the driver ends up calling nvmet_req_complete()
passing a status error.
The problem is that at this point cmd->req is not yet initialized,
the kernel will crash after dereferencing a NULL pointer.
Fix the bug by replacing the call to nvmet_req_complete() with
nvmet_tcp_fatal_error().
Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver")
Reviewed-by: Keith Busch <kbsuch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa56305908ba20de2104f1b8508c6a7401833be ]
If the host sends an H2CData command with an invalid DATAL,
the kernel may crash in nvmet_tcp_build_pdu_iovec().
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
lr : nvmet_tcp_io_work+0x6ac/0x718 [nvmet_tcp]
Call trace:
process_one_work+0x174/0x3c8
worker_thread+0x2d0/0x3e8
kthread+0x104/0x110
Fix the bug by raising a fatal error if DATAL isn't coherent
with the packet size.
Also, the PDU length should never exceed the MAXH2CDATA parameter which
has been communicated to the host in nvmet_tcp_handle_icreq().
Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66aad7d8d3ec5a3a8ec2023841bcec2ded5f65c9 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7bb94 ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24f2cd019946fc2e88e632d2e24a34c2cc3f2be4 ]
Now, the "jumped-over" code is simple enough to be put inside an 'if'.
Do so to make it 'goto'-less.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd99392b643b824813df2edbaebe26a2136d31e6 ]
msleep_interruptible() will check on its own. So no need to do the check
in send_break() before calling the above.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66619686d187b4a6395316b7f39881e945dce4bc ]
If the driver sets TTY_DRIVER_HARDWARE_BREAK, we leave ops->break_ctl()
to the driver and return from send_break(). But we do it using a local
variable and keep the code flowing through the end of the function.
Instead, do 'return' immediately with the ops->break_ctl()'s return
value.
This way, we don't have to stuff the 'else' branch of the 'if' with the
software break handling. And we can re-indent the function too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b73f08bb7fe5a0901646ca5ceaa1e7a2d5ee6293 ]
When reading in_voltage_scale we can get something like:
root@analog:/sys/bus/iio/devices/iio:device2# cat in_voltage_scale
0.038146
However, when reading the available options:
root@analog:/sys/bus/iio/devices/iio:device2# cat
in_voltage_scale_available
2000.000000 2100.000006 2200.000007 2300.000008 2400.000009 2500.000010
which does not make sense. Moreover, when trying to set a new scale we
get an error because there's no call to __ad9467_get_scale() to give us
values as given when reading in_voltage_scale. Fix it by computing the
available scales during probe and properly pass the list when
.read_available() is called.
While at it, change to use .read_available() from iio_info. Also note
that to properly fix this, adi-axi-adc.c has to be changed accordingly.
Fixes: ad6797120238 ("iio: adc: ad9467: add support AD9467 ADC")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-4-a4a33bc4d70e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76f028539cf360f750efd8cde560edda298e4c6b ]
The reset gpio was being handled with inverted polarity. This means that
as far as gpiolib is concerned we were actually leaving the pin asserted
(in theory, this would mean reset). However, inverting the polarity in
devicetree made things work. Fix it by doing it the proper way and how
gpiolib expects it to be done.
While at it, moved the handling to it's own function and dropped
'reset_gpio' from the 'struct ad9467_state' as we only need it during
probe. On top of that, refactored things so that we now request the gpio
asserted (i.e in reset) and then de-assert it. Also note that we now use
gpiod_set_value_cansleep() instead of gpiod_direction_output() as we
already request the pin as output.
Fixes: ad6797120238 ("iio: adc: ad9467: add support AD9467 ADC")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-1-a4a33bc4d70e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
