commit 71cd7e80cfde548959952eac7063aeaea1f2e1c6 upstream.
An S4 (suspend to disk) test on the LoongArch 3A6000 platform sometimes
fails with the following error messaged in the dmesg log:
Invalid LZO compressed length
That happens because when compressing/decompressing the image, the
synchronization between the control thread and the compress/decompress/crc
thread is based on a relaxed ordering interface, which is unreliable, and the
following situation may occur:
CPU 0 CPU 1
save_image_lzo lzo_compress_threadfn
atomic_set(&d->stop, 1);
atomic_read(&data[thr].stop)
data[thr].cmp = data[thr].cmp_len;
WRITE data[thr].cmp_len
Then CPU0 gets a stale cmp_len and writes it to disk. During resume from S4,
wrong cmp_len is loaded.
To maintain data consistency between the two threads, use the acquire/release
variants of atomic set and read operations.
Fixes: 081a9d043c98 ("PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hongchen Zhang <zhanghongchen@loongson.cn>
Co-developed-by: Weihao Li <liweihao@loongson.cn>
Signed-off-by: Weihao Li <liweihao@loongson.cn>
[ rjw: Subject rewrite and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c784d624819acbeefb0018bac89e632467cca5a upstream.
The ext4 filesystem tracks the trim status of blocks at the group
level. When an entire group has been trimmed then it is marked as
such and subsequent trim invocations with the same minimum trim size
will not be attempted on that group unless it is marked as able to be
trimmed again such as when a block is freed.
Currently the last group can't be marked as trimmed due to incorrect
logic in ext4_last_grp_cluster(). ext4_last_grp_cluster() is supposed
to return the zero based index of the last cluster in a group. This is
then used by ext4_try_to_trim_range() to determine if the trim
operation spans the entire group and as such if the trim status of the
group should be recorded.
ext4_last_grp_cluster() takes a 0 based group index, thus the valid
values for grp are 0..(ext4_get_groups_count - 1). Any group index
less than (ext4_get_groups_count - 1) is not the last group and must
have EXT4_CLUSTERS_PER_GROUP(sb) clusters. For the last group we need
to calculate the number of clusters based on the number of blocks in
the group. Finally subtract 1 from the number of clusters as zero
based indexing is expected. Rearrange the function slightly to make
it clear what we are calculating and returning.
Reproducer:
// Create file system where the last group has fewer blocks than
// blocks per group
$ mkfs.ext4 -b 4096 -g 8192 /dev/nvme0n1 8191
$ mount /dev/nvme0n1 /mnt
Before Patch:
$ fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
// Group not marked as trimmed so second invocation still discards blocks
$ fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
After Patch:
fstrim -v /mnt
/mnt: 25.9 MiB (27156480 bytes) trimmed
// Group marked as trimmed so second invocation DOESN'T discard any blocks
fstrim -v /mnt
/mnt: 0 B (0 bytes) trimmed
Fixes: 45e4ab320c9b ("ext4: move setting of trimmed bit into ext4_try_to_trim_range()")
Cc: <stable@vger.kernel.org> # 4.19+
Signed-off-by: Suraj Jitindar Singh <surajjs@amazon.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231213051635.37731-1-surajjs@amazon.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0080af84d3fb2423f0b3b55eff666f545eb097 upstream.
In order to avoid unnecessary pollution of the global symbol namespace
move the core/library functions into a specific namespace and import
that into the various specific device drivers that use them.
For more information see https://lwn.net/Articles/760045/
An alternative here would be to conclude that we are unlikely to see
support for the other ad7091r parts in the near future and just merge
the two modules into one supporting just the i2c -5 variant.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-3-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f5c24d94512f1b288262beda4d3dcb9629222fc7 ]
__dma_async_device_channel_register() can fail. In case of failure,
chan->local is freed (with free_percpu()), and chan->local is nullified.
When dma_async_device_unregister() is called (because of managed API or
intentionally by DMA controller driver), channels are unconditionally
unregistered, leading to this NULL pointer:
[ 1.318693] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000d0
[...]
[ 1.484499] Call trace:
[ 1.486930] device_del+0x40/0x394
[ 1.490314] device_unregister+0x20/0x7c
[ 1.494220] __dma_async_device_channel_unregister+0x68/0xc0
Look at dma_async_device_register() function error path, channel device
unregistration is done only if chan->local is not NULL.
Then add the same condition at the beginning of
__dma_async_device_channel_unregister() function, to avoid NULL pointer
issue whatever the API used to reach this function.
Fixes: d2fb0a043838 ("dmaengine: break out channel registration")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20231213160452.2598073-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e71c5c89bcb165a02df35325aa13d1ee40112401 ]
The ADC needs a voltage reference to work correctly.
Users can provide an external voltage reference or use the chip internal
reference to operate the ADC.
The availability of an in chip reference for the ADC saves the user from
having to supply an external voltage reference, which makes the external
reference an optional property as described in the device tree
documentation.
Though, to use the internal reference, it must be enabled by writing to
the configuration register.
Enable AD7091R internal voltage reference if no external vref is supplied.
Fixes: 260442cc5be4 ("iio: adc: ad7091r5: Add scale and external VREF support")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/b865033fa6a4fc4bf2b4a98ec51a6144e0f64f77.1703013352.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020e71c7ffc25dfe29ed9be6c2d39af7bd7f661f ]
AD7091R-5 devices are supported by the ad7091r-5 driver together with
the ad7091r-base driver. Those drivers declared iio events for notifying
user space when ADC readings fall bellow the thresholds of low limit
registers or above the values set in high limit registers.
However, to configure iio events and their thresholds, a set of callback
functions must be implemented and those were not present until now.
The consequence of trying to configure ad7091r-5 events without the
proper callback functions was a null pointer dereference in the kernel
because the pointers to the callback functions were not set.
Implement event configuration callbacks allowing users to read/write
event thresholds and enable/disable event generation.
Since the event spec structs are generic to AD7091R devices, also move
those from the ad7091r-5 driver the base driver so they can be reused
when support for ad7091r-2/-4/-8 be added.
Fixes: ca69300173b6 ("iio: adc: Add support for AD7091R5 ADC")
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/59552d3548dabd56adc3107b7b4869afee2b0c3c.1703013352.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 149694f5e79b0c7a36ceb76e7c0d590db8f151c1 ]
The ad7091r-base driver sets up an interrupt handler for firing events
when inputs are either above or below a certain threshold.
However, for the interrupt signal to come from the device it must be
configured to enable the ALERT/BUSY/GPO pin to be used as ALERT, which
was not being done until now.
Enable interrupt signals on the ALERT/BUSY/GPO pin by setting the proper
bit in the configuration register.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/e8da2ee98d6df88318b14baf3dc9630e20218418.1702746240.git.marcelo.schmitt1@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 020e71c7ffc2 ("iio: adc: ad7091r: Allow users to configure device events")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d710b769c1f5f0d55c9ad9bb49b7dce009ec103 ]
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 029b42d8519cef70c4fb5fcaccd08f1053ed2bf0 ]
Provide a macro to filter all SPI_MODE_0,1,2,3 mode in one run.
The latest SPI framework will parse the devicetree in following call
sequence: of_register_spi_device() -> of_spi_parse_dt()
So, driver do not need to pars the devicetree and will get prepared
flags in the probe.
On one hand it is good far most drivers. On other hand some drivers need to
filter flags provide by SPI framework and apply know to work flags. This drivers
may use SPI_MODE_X_MASK to filter MODE flags and set own, known flags:
spi->flags &= ~SPI_MODE_X_MASK;
spi->flags |= SPI_MODE_0;
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201027095724.18654-2-o.rempel@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 6d710b769c1f ("serial: sc16is7xx: add check for unsupported SPI modes during probe")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ef79cd1412236d884ab0c46b4d1921380807b48 ]
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2c77032fcbe515194107994d12cd72ddb77b022 ]
The macros for the unit conversion for frequency are duplicated in
different places.
Provide these macros in the 'units' header, so they can be reused.
Link: https://lkml.kernel.org/r/20210816114732.1834145-3-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 3ef79cd14122 ("serial: sc16is7xx: set safe default SPI clock frequency")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9221919a2d2df5741ab074dfec5bdfc6f1e043b ]
Patch series "Add Hz macros", v3.
There are multiple definitions of the HZ_PER_MHZ or HZ_PER_KHZ in the
different drivers. Instead of duplicating this definition again and
again, add one in the units.h header to be reused in all the place the
redefiniton occurs.
At the same time, change the type of the Watts, as they can not be
negative.
This patch (of 10):
The users of the macros are safe to be assigned with an unsigned instead
of signed as the variables using them are themselves unsigned.
Link: https://lkml.kernel.org/r/20210816114732.1834145-1-daniel.lezcano@linaro.org
Link: https://lkml.kernel.org/r/20210816114732.1834145-2-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 3ef79cd14122 ("serial: sc16is7xx: set safe default SPI clock frequency")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e11c29873a8a296a20f99b3e03095e65ebf897d ]
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording]
Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com
Fixes: 43e6409db64d ("PCI: mediatek: Add MSI support for MT2712 and MT7622")
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40c304109e866a7dc123661a5c8ca72f6b5e14e0 ]
Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.
Data pattern likes below when sg enabled, package size is 1k and mult is 2
[UVC Header(8B) ] [data(3k - 8)] ...
The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
0xd000: wrong
0xe000: wrong
0xf000: correct
0x10000: wrong
0x11000: wrong
0x12000: correct
...
To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92f02efa1d86d7dcaef7f38a5fe3396c4e88a93c ]
ISO basic transfer is
ITP(SOF) Package_0 Package_1 ... Package_n
CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.
According USB spec defination:
Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)
Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.
Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-3-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2627335a1329a0d39d8d277994678571c4f21800 ]
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 92f02efa1d86 ("usb: cdns3: fix iso transfer error when mult is not zero")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b8be5ecff26201bafb0a554c74e91571299fb94 ]
When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.
cdns3_prepare_trb: ep2in: trb 0000000000ac755f, dma buf: 0xbf455000, size: 8, burst: 128 ctrl: 0x00000415 (C=1, T=0, ISP, CHAIN, Normal)
cdns3_prepare_trb: ep2in: trb 00000000a574e693, dma buf: 0xc0200fe0, size: 1016, burst: 128 ctrl: 0x00000405 (C=1, T=0, ISP, Normal)
But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.
The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.
Fixed it by below major steps:
1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.
.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB, LINK_TRB ... LINK_TRB
^End of TRB List
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fba8701baed76eac00b84b59f09f6a077f24c534 ]
Patch fixes the following warnings:
cdns3-gadget.c:1203: sparse: warning: incorrect type
in assignment (different base types)
cdns3-gadget.c:1203: sparse: expected restricted __le32 [usertype] length
cdns3-gadget.c:1203: sparse: got unsigned long
cdns3-gadget.c:1250: sparse: warning: invalid assignment: |=
cdns3-gadget.c:1250: sparse: left side has type restricted __le32
cdns3-gadget.c:1250: sparse: right side has type unsigned long
cdns3-gadget.c:1253: sparse: warning: invalid assignment: |=
cdns3-gadget.c:1253: sparse: left side has type restricted __le32
cdns3-gadget.c:1253: sparse: right side has type unsigned long
cdns3-ep0.c:367: sparse: warning: restricted __le16 degrades to integer
cdns3-ep0.c:792: sparse: warning: symbol 'cdns3_gadget_ep0_ops' was not
declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Stable-dep-of: 1b8be5ecff26 ("usb: cdns3: fix uvc failure work since sg support enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 990489e1042c6c5d6bccf56deca68f8dbeed8180 ]
To properly handle ACK on the bus when transferring more than one
message in polling mode, move the polling handling loop from
s3c24xx_i2c_message_start() to s3c24xx_i2c_doxfer(). This way
i2c_s3c_irq_nextbyte() is always executed till the end, properly
acknowledging the IRQ bits and no recursive calls to
i2c_s3c_irq_nextbyte() are made.
While touching this, also fix finishing transfers in polling mode by
using common code path and always waiting for the bus to become idle
and disabled.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9cf23ed55d7ba3ab26d617a3ae507863674c8f ]
To properly handle read transfers in polling mode, no waiting for the ACK
state is needed as it will never come. Just wait a bit to ensure start
state is on the bus and continue processing next bytes.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b34f4de6d30cbaa8fed905a5080b6eace8c84dc7 ]
'qos_pfc' test checks PFC behavior. The idea is to limit the traffic
using a shaper somewhere in the flow of the packets. In this area, the
buffer is smaller than the buffer at the beginning of the flow, so it fills
up until there is no more space left. The test configures there PFC
which is supposed to notice that the headroom is filling up and send PFC
Xoff to indicate the transmitter to stop sending traffic for the priorities
sharing this PG.
The Xon/Xoff threshold is auto-configured and always equal to
2*(MTU rounded up to cell size). Even after sending the PFC Xoff packet,
traffic will keep arriving until the transmitter receives and processes
the PFC packet. This amount of traffic is known as the PFC delay allowance.
Currently the buffer for the delay traffic is configured as 100KB. The
MTU in the test is 10KB, therefore the threshold for Xoff is about 20KB.
This allows 80KB extra to be stored in this buffer.
8-lane ports use two buffers among which the configured buffer is split,
the Xoff threshold then applies to each buffer in parallel.
The test does not take into account the behavior of 8-lane ports, when the
ports are configured to 400Gbps with 8 lanes or 800Gbps with 8 lanes,
packets are dropped and the test fails.
Check if the relevant ports use 8 lanes, in such case double the size of
the buffer, as the headroom is split half-half.
Cc: Shuah Khan <shuah@kernel.org>
Fixes: bfa804784e32 ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/23ff11b7dff031eb04a41c0f5254a2b636cd8ebb.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0bab2298ec9b3a837f8ef4a0cae4b42a4d03365 ]
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: b34f4de6d30c ("selftests: mlxsw: qos_pfc: Adjust the test to support 8 lanes")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483ae90d8f976f8339cf81066312e1329f2d3706 ]
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Reported-by: Orel Hagag <orelh@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/2d91c89afba59c22587b444994ae419dbea8d876.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 194ab9476089bbfc021073214e071a404e375ee6 ]
Move the initialization and de-initialization code further below in
order to avoid forward declarations in the next patch. No functional
changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 483ae90d8f97 ("mlxsw: spectrum_acl_tcam: Fix stack corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61fe3b9102ac84ba479ab84d8f5454af2e21e468 ]
Move mutex_destroy() to the end to make the function symmetric with
mlxsw_sp_acl_tcam_init(). No functional changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 483ae90d8f97 ("mlxsw: spectrum_acl_tcam: Fix stack corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c087dfcc9d5e7e8557d217f01f58ba42d1ddbf1 ]
Use 'bitmap_zalloc()' to simplify code, improve the semantic and avoid
some open-coded arithmetic in allocator arguments.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 483ae90d8f97 ("mlxsw: spectrum_acl_tcam: Fix stack corruption")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d6eeabcfaba2fcadf5443b575789ea606f9de83 ]
Lately, a bug was found when many TC filters are added - at some point,
several bugs are printed to dmesg [1] and the switch is crashed with
segmentation fault.
The issue starts when gen_pool_free() fails because of unexpected
behavior - a try to free memory which is already freed, this leads to BUG()
call which crashes the switch and makes many other bugs.
Trying to track down the unexpected behavior led to a bug in eRP code. The
function mlxsw_sp_acl_erp_table_alloc() gets a pointer to the allocated
index, sets the value and returns an error code. When gen_pool_alloc()
fails it returns address 0, we track it and return -ENOBUFS outside, BUT
the call for gen_pool_alloc() already override the index in erp_table
structure. This is a problem when such allocation is done as part of
table expansion. This is not a new table, which will not be used in case
of allocation failure. We try to expand eRP table and override the
current index (non-zero) with zero. Then, it leads to an unexpected
behavior when address 0 is freed twice. Note that address 0 is valid in
erp_table->base_index and indeed other tables use it.
gen_pool_alloc() fails in case that there is no space left in the
pre-allocated pool, in our case, the pool is limited to
ACL_MAX_ERPT_BANK_SIZE, which is read from hardware. When more than max
erp entries are required, we exceed the limit and return an error, this
error leads to "Failed to migrate vregion" print.
Fix this by changing erp_table->base_index only in case of a successful
allocation.
Add a test case for such a scenario. Without this fix it causes
segmentation fault:
$ TESTS="max_erp_entries_test" ./tc_flower.sh
./tc_flower.sh: line 988: 1560 Segmentation fault tc filter del dev $h2 ingress chain $i protocol ip pref $i handle $j flower &>/dev/null
[1]:
kernel BUG at lib/genalloc.c:508!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 3531 Comm: tc Not tainted 6.7.0-rc5-custom-ga6893f479f5e #1
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:gen_pool_free_owner+0xc9/0xe0
...
Call Trace:
<TASK>
__mlxsw_sp_acl_erp_table_other_dec+0x70/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_erp_mask_destroy+0xf5/0x110 [mlxsw_spectrum]
objagg_obj_root_destroy+0x18/0x80 [objagg]
objagg_obj_destroy+0x12c/0x130 [objagg]
mlxsw_sp_acl_erp_mask_put+0x37/0x50 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_region_entry_remove+0x74/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_entry_del+0x1e/0x40 [mlxsw_spectrum]
mlxsw_sp_acl_tcam_ventry_del+0x78/0xd0 [mlxsw_spectrum]
mlxsw_sp_flower_destroy+0x4d/0x70 [mlxsw_spectrum]
mlxsw_sp_flow_block_cb+0x73/0xb0 [mlxsw_spectrum]
tc_setup_cb_destroy+0xc1/0x180
fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
__fl_delete+0x1ac/0x1c0 [cls_flower]
fl_destroy+0xc2/0x150 [cls_flower]
tcf_proto_destroy+0x1a/0xa0
...
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
Fixes: f465261aa105 ("mlxsw: spectrum_acl: Implement common eRP core")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/4cfca254dfc0e5d283974801a24371c7b6db5989.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1172f3ee3a98754d95b968968920a7d03fdebcc ]
Accessing an ethernet device that is powered off or clock gated might
cause the CPU to hang. Add ethnl_ops_begin/complete in
ethnl_set_features() to protect against this.
Fixes: 0980bfcd6954 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Ludvig Pärsson <ludvig.parsson@axis.com>
Link: https://lore.kernel.org/r/20240117-etht2-v2-1-1a96b6e8c650@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f41d30cd6dc865c3cbc1a852372321eba6d4e4c ]
When appending "[defcmd]" to 'kdb_prompt_str', the size of the string
already in the buffer should be taken into account.
An option could be to switch from strncat() to strlcat() which does the
correct test to avoid such an overflow.
However, this actually looks as dead code, because 'defcmd_in_progress'
can't be true here.
See a more detailed explanation at [1].
[1]: https://lore.kernel.org/all/CAD=FV=WSh7wKN7Yp-3wWiDgX4E3isQ8uh0LCzTmd1v9Cg9j+nQ@mail.gmail.com/
Fixes: 5d5314d6795f ("kdb: core for kgdb back end (1 of 2)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6938c1c76c64f42363d0d1f051e1b4641c2ad40 ]
Inside decrement_ttl() upon discovering that the packet ttl has exceeded,
__IP_INC_STATS and __IP6_INC_STATS macros can be called from preemptible
context having the following backtrace:
check_preemption_disabled: 48 callbacks suppressed
BUG: using __this_cpu_add() in preemptible [00000000] code: curl/1177
caller is decrement_ttl+0x217/0x830
CPU: 5 PID: 1177 Comm: curl Not tainted 6.7.0+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0xbd/0xe0
check_preemption_disabled+0xd1/0xe0
decrement_ttl+0x217/0x830
__ip_vs_get_out_rt+0x4e0/0x1ef0
ip_vs_nat_xmit+0x205/0xcd0
ip_vs_in_hook+0x9b1/0x26a0
nf_hook_slow+0xc2/0x210
nf_hook+0x1fb/0x770
__ip_local_out+0x33b/0x640
ip_local_out+0x2a/0x490
__ip_queue_xmit+0x990/0x1d10
__tcp_transmit_skb+0x288b/0x3d10
tcp_connect+0x3466/0x5180
tcp_v4_connect+0x1535/0x1bb0
__inet_stream_connect+0x40d/0x1040
inet_stream_connect+0x57/0xa0
__sys_connect_file+0x162/0x1a0
__sys_connect+0x137/0x160
__x64_sys_connect+0x72/0xb0
do_syscall_64+0x6f/0x140
entry_SYSCALL_64_after_hwframe+0x6e/0x76
RIP: 0033:0x7fe6dbbc34e0
Use the corresponding preemption-aware variants: IP_INC_STATS and
IP6_INC_STATS.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 8d8e20e2d7bb ("ipvs: Decrement ttl")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 113661e07460a6604aacc8ae1b23695a89e7d4b3 ]
It is still possible to set on the NFT_SET_CONCAT flag by specifying a
set size and no field description, report EINVAL in such case.
Fixes: 1b6345d4160e ("netfilter: nf_tables: check NFT_SET_CONCAT flag if field_count is specified")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b1ca88e4bb63673dc9f9c7f23c899f22c3cb17a ]
Delete from packet path relies on the garbage collector to purge
elements with NFT_SET_ELEM_DEAD_BIT on.
Skip these dead elements from nf_tables_dump_setelem() path, I very
rarely see tests/shell/testcases/maps/typeof_maps_add_delete reports
[DUMP FAILED] showing a mismatch in the expected output with an element
that should not be there.
If the netlink dump happens before GC worker run, it might show dead
elements in the ruleset listing.
nft_rhash_get() already skips dead elements in nft_rhash_cmp(),
therefore, it already does not show the element when getting a single
element via netlink control plane.
Fixes: 5f68718b34a5 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ce67e3793f48c1b9635beb9bb71116ca1e51b58 ]
The set description provides the size of each field in the set whose sum
should not mismatch the set key length, bail out otherwise.
I did not manage to crash nft_set_pipapo with mismatch fields and set key
length so far, but this is UB which must be disallowed.
Fixes: f3a2181e16f1 ("netfilter: nf_tables: Support for sets with multiple ranged fields")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e327b2372bc0f18c30433ac40be07741b59231c5 ]
In ravb_start_xmit(), ravb driver uses u32 variable to store result of
dma_map_single() call. Since ravb hardware has 32-bit address fields in
descriptors, this works properly when mapping is successful - it is
platform's job to provide mapping addresses that fit into hardware
limitations.
However, in failure case dma_map_single() returns DMA_MAPPING_ERROR
constant that is 64-bit when dma_addr_t is 64-bit. Storing this constant
in u32 leads to truncation, and further call to dma_mapping_error()
fails to notice the error.
Fix that by storing result of dma_map_single() in a dma_addr_t
variable.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e398822c4751017fe401f57409488f5948d12fb5 ]
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64e47d8afb5ca533b27efc006405e5bcae2c4a7b ]
The value of AM65_CPSW_MAX_PACKET_SIZE represents the maximum length
of a received frame. This value is written to the register
AM65_CPSW_PORT_REG_RX_MAXLEN.
The maximum MTU configured on the network device should then leave
some room for the ethernet headers and frame check. Otherwise, if
the network interface is configured to its maximum mtu possible,
the frames will be larger than AM65_CPSW_MAX_PACKET_SIZE and will
get dropped as oversized.
The switch supports ethernet frame sizes between 64 and 2024 bytes
(including VLAN) as stated in the technical reference manual, so
define AM65_CPSW_MAX_PACKET_SIZE with that maximum size.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240105085530.14070-2-jorge.sanjuangarcia@duagon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80df7d6af7f6d229b34cf237b2cc9024c07111cd ]
The zpci_get_max_write_size() helper is used to determine the maximum
size a PCI store or load can use at a given __iomem address.
For the PCI block store the following restrictions apply:
1. The dst + len must not cross a 4K boundary in the (pseudo-)MMIO space
2. len must not exceed ZPCI_MAX_WRITE_SIZE
3. len must be a multiple of 8 bytes
4. The src address must be double word (8 byte) aligned
5. The dst address must be double word (8 byte) aligned
Otherwise only a normal PCI store which takes its src value from
a register can be used. For these PCI store restriction 1 still applies.
Similarly 1 also applies to PCI loads.
It turns out zpci_max_write_size() instead implements stricter
conditions which prevents PCI block stores from being used where they
can and should be used. In particular instead of conditions 4 and 5 it
wrongly enforces both dst and src to be size aligned. This indirectly
covers condition 1 but also prevents many legal PCI block stores.
On top of the functional shortcomings the zpci_get_max_write_size() is
misnamed as it is used for both read and write size calculations. Rename
it to zpci_get_max_io_size() and implement the listed conditions
explicitly.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Fixes: cd24834130ac ("s390/pci: base support")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
[agordeev@linux.ibm.com replaced spaces with tabs]
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12ca110c613a81cb0f0099019c839d078cd0f38 ]
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab47 ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a1abc24850eb759e36a2f8869161c3b7254c904 ]
The nvmet_tcp_handle_h2c_data_pdu() function should take into
consideration the possibility that the header digest and/or the data
digests are enabled when calculating the expected PDU length, before
comparing it to the value stored in cmd->pdu_len.
Fixes: efa56305908b ("nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55a8210c9e7d21ff2644809699765796d4bfb200 ]
When processing a packed profile in unpack_profile() described like
"profile :ns::samba-dcerpcd /usr/lib*/samba/{,samba/}samba-dcerpcd {...}"
a string ":samba-dcerpcd" is unpacked as a fully-qualified name and then
passed to aa_splitn_fqname().
aa_splitn_fqname() treats ":samba-dcerpcd" as only containing a namespace.
Thus it returns NULL for tmpname, meanwhile tmpns is non-NULL. Later
aa_alloc_profile() crashes as the new profile name is NULL now.
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 6 PID: 1657 Comm: apparmor_parser Not tainted 6.7.0-rc2-dirty #16
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
RIP: 0010:strlen+0x1e/0xa0
Call Trace:
<TASK>
? strlen+0x1e/0xa0
aa_policy_init+0x1bb/0x230
aa_alloc_profile+0xb1/0x480
unpack_profile+0x3bc/0x4960
aa_unpack+0x309/0x15e0
aa_replace_profiles+0x213/0x33c0
policy_update+0x261/0x370
profile_replace+0x20e/0x2a0
vfs_write+0x2af/0xe00
ksys_write+0x126/0x250
do_syscall_64+0x46/0xf0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
</TASK>
---[ end trace 0000000000000000 ]---
RIP: 0010:strlen+0x1e/0xa0
It seems such behaviour of aa_splitn_fqname() is expected and checked in
other places where it is called (e.g. aa_remove_profiles). Well, there
is an explicit comment "a ns name without a following profile is allowed"
inside.
AFAICS, nothing can prevent unpacked "name" to be in form like
":samba-dcerpcd" - it is passed from userspace.
Deny the whole profile set replacement in such case and inform user with
EPROTO and an explaining message.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 04dc715e24d0 ("apparmor: audit policy ns specified in policy load")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c51f8788b5d4e9f46afbcf563255cfd355690b3 ]
Add variants of perf_env__insert_bpf_prog_info(), perf_env__insert_btf()
and perf_env__find_btf prefixed with __ to indicate the
env->bpf_progs.lock is assumed held.
Call these variants when the lock is held to avoid recursively taking it
and potentially having a thread deadlock with itself.
Fixes: f8dfeae009effc0b ("perf bpf: Show more BPF program info in print_bpf_prog_info()")
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: K Prateek Nayak <kprateek.nayak@amd.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ming Wang <wangming01@loongson.cn>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/r/20231207014655.1252484-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0849a5441358cef02586fb2d60f707c0db195628 ]
in nvmet_tcp_handle_h2c_data_pdu(), if the host sends a data_offset
different from rbytes_done, the driver ends up calling nvmet_req_complete()
passing a status error.
The problem is that at this point cmd->req is not yet initialized,
the kernel will crash after dereferencing a NULL pointer.
Fix the bug by replacing the call to nvmet_req_complete() with
nvmet_tcp_fatal_error().
Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver")
Reviewed-by: Keith Busch <kbsuch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa56305908ba20de2104f1b8508c6a7401833be ]
If the host sends an H2CData command with an invalid DATAL,
the kernel may crash in nvmet_tcp_build_pdu_iovec().
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
lr : nvmet_tcp_io_work+0x6ac/0x718 [nvmet_tcp]
Call trace:
process_one_work+0x174/0x3c8
worker_thread+0x2d0/0x3e8
kthread+0x104/0x110
Fix the bug by raising a fatal error if DATAL isn't coherent
with the packet size.
Also, the PDU length should never exceed the MAXH2CDATA parameter which
has been communicated to the host in nvmet_tcp_handle_icreq().
Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66aad7d8d3ec5a3a8ec2023841bcec2ded5f65c9 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7bb94 ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
