FireAsf 🔥
0b54c32362
[ Upstream commit e398822c4751017fe401f57409488f5948d12fb5 ]
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
||
|---|---|---|
| .github/workflows | ||
| android | ||
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| firmware/tsp_goodix | ||
| fs | ||
| gki | ||
| include | ||
| init | ||
| io_uring | ||
| ipc | ||
| kernel | ||
| kernel_build | ||
| kunitconfigs | ||
| lib | ||
| LICENSES | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| test | ||
| tools | ||
| usr | ||
| virt | ||
| build.config.aarch64 | ||
| build.config.allmodconfig | ||
| build.config.allmodconfig.aarch64 | ||
| build.config.allmodconfig.arm | ||
| build.config.allmodconfig.x86_64 | ||
| build.config.amlogic | ||
| build.config.arm | ||
| build.config.common | ||
| build.config.db845c | ||
| build.config.erd8825_a25_s | ||
| build.config.erd8825_s | ||
| build.config.erd9925_evt0_s | ||
| build.config.erd9925_evt0_s5300_s | ||
| build.config.erd9925_s | ||
| build.config.gki | ||
| build.config.gki-debug.aarch64 | ||
| build.config.gki-debug.x86_64 | ||
| build.config.gki.aarch64 | ||
| build.config.gki.aarch64.fips140 | ||
| build.config.gki.aarch64.fips140_eval_testing | ||
| build.config.gki.x86_64 | ||
| build.config.gki_kasan | ||
| build.config.gki_kasan.aarch64 | ||
| build.config.gki_kasan.x86_64 | ||
| build.config.gki_kprobes | ||
| build.config.gki_kprobes.aarch64 | ||
| build.config.gki_kprobes.x86_64 | ||
| build.config.hikey960 | ||
| build.config.khwasan | ||
| build.config.mcd | ||
| build.config.rockchip | ||
| build.config.universal2100_s | ||
| build.config.universal8825_s | ||
| build.config.universal9925_evt0_s | ||
| build.config.universal9925_s | ||
| build.config.x86_64 | ||
| build.sh | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| linux-stable.sh | ||
| MAINTAINERS | ||
| Makefile | ||
| OWNERS | ||
| README | ||
| README.md | ||
| vendor_boot_module_order_exynos2100.cfg | ||
| vendor_boot_module_order_s5e8825.cfg | ||
| vendor_boot_module_order_s5e9925.cfg | ||
| vendor_module_list_s5e8825.cfg | ||
| vendor_module_list_s5e9925.cfg | ||
| vendor_module_list_s5e9925_b0s.cfg | ||
| vendor_module_list_s5e9925_g0s.cfg | ||
| vendor_module_list_s5e9925_r0s.cfg | ||
How do I submit patches to Android Common Kernels
-
BEST: Make all of your changes to upstream Linux. If appropriate, backport to the stable releases. These patches will be merged automatically in the corresponding common kernels. If the patch is already in upstream Linux, post a backport of the patch that conforms to the patch requirements below.
- Do not send patches upstream that contain only symbol exports. To be considered for upstream Linux,
additions of
EXPORT_SYMBOL_GPL()require an in-tree modular driver that uses the symbol -- so include the new driver or changes to an existing driver in the same patchset as the export. - When sending patches upstream, the commit message must contain a clear case for why the patch is needed and beneficial to the community. Enabling out-of-tree drivers or functionality is not not a persuasive case.
- Do not send patches upstream that contain only symbol exports. To be considered for upstream Linux,
additions of
-
LESS GOOD: Develop your patches out-of-tree (from an upstream Linux point-of-view). Unless these are fixing an Android-specific bug, these are very unlikely to be accepted unless they have been coordinated with kernel-team@android.com. If you want to proceed, post a patch that conforms to the patch requirements below.
Common Kernel patch requirements
- All patches must conform to the Linux kernel coding standards and pass
script/checkpatch.pl - Patches shall not break gki_defconfig or allmodconfig builds for arm, arm64, x86, x86_64 architectures (see https://source.android.com/setup/build/building-kernels)
- If the patch is not merged from an upstream branch, the subject must be tagged with the type of patch:
UPSTREAM:,BACKPORT:,FROMGIT:,FROMLIST:, orANDROID:. - All patches must have a
Change-Id:tag (see https://gerrit-review.googlesource.com/Documentation/user-changeid.html) - If an Android bug has been assigned, there must be a
Bug:tag. - All patches must have a
Signed-off-by:tag by the author and the submitter
Additional requirements are listed below based on patch type
Requirements for backports from mainline Linux: UPSTREAM:, BACKPORT:
- If the patch is a cherry-pick from Linux mainline with no changes at all
- tag the patch subject with
UPSTREAM:. - add upstream commit information with a
(cherry picked from commit ...)line - Example:
- if the upstream commit message is
- tag the patch subject with
important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
- then Joe Smith would upload the patch for the common kernel as
UPSTREAM: important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
Bug: 135791357
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
(cherry picked from commit c31e73121f4c1ec41143423ac6ce3ce6dafdcec1)
Signed-off-by: Joe Smith <joe.smith@foo.org>
- If the patch requires any changes from the upstream version, tag the patch with
BACKPORT:instead ofUPSTREAM:.- use the same tags as
UPSTREAM: - add comments about the changes under the
(cherry picked from commit ...)line - Example:
- use the same tags as
BACKPORT: important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
Bug: 135791357
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
(cherry picked from commit c31e73121f4c1ec41143423ac6ce3ce6dafdcec1)
[joe: Resolved minor conflict in drivers/foo/bar.c ]
Signed-off-by: Joe Smith <joe.smith@foo.org>
Requirements for other backports: FROMGIT:, FROMLIST:,
- If the patch has been merged into an upstream maintainer tree, but has not yet
been merged into Linux mainline
- tag the patch subject with
FROMGIT: - add info on where the patch came from as
(cherry picked from commit <sha1> <repo> <branch>). This must be a stable maintainer branch (not rebased, so don't uselinux-nextfor example). - if changes were required, use
BACKPORT: FROMGIT: - Example:
- if the commit message in the maintainer tree is
- tag the patch subject with
important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
- then Joe Smith would upload the patch for the common kernel as
FROMGIT: important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
Bug: 135791357
(cherry picked from commit 878a2fd9de10b03d11d2f622250285c7e63deace
https://git.kernel.org/pub/scm/linux/kernel/git/foo/bar.git test-branch)
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
Signed-off-by: Joe Smith <joe.smith@foo.org>
- If the patch has been submitted to LKML, but not accepted into any maintainer tree
- tag the patch subject with
FROMLIST: - add a
Link:tag with a link to the submittal on lore.kernel.org - add a
Bug:tag with the Android bug (required for patches not accepted into a maintainer tree) - if changes were required, use
BACKPORT: FROMLIST: - Example:
- tag the patch subject with
FROMLIST: important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
Bug: 135791357
Link: https://lore.kernel.org/lkml/20190619171517.GA17557@someone.com/
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
Signed-off-by: Joe Smith <joe.smith@foo.org>
Requirements for Android-specific patches: ANDROID:
- If the patch is fixing a bug to Android-specific code
- tag the patch subject with
ANDROID: - add a
Fixes:tag that cites the patch with the bug - Example:
- tag the patch subject with
ANDROID: fix android-specific bug in foobar.c
This is the detailed description of the important fix
Fixes: 1234abcd2468 ("foobar: add cool feature")
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
Signed-off-by: Joe Smith <joe.smith@foo.org>
- If the patch is a new feature
- tag the patch subject with
ANDROID: - add a
Bug:tag with the Android bug (required for android-specific features)
- tag the patch subject with