This reverts commit 462c383e732fa99c60aff711c43ec9d6eb27921e which is
commit 27016f75f5ed47e2d8e0ca75a8ff1f40bc1a5e27 upstream.
It is reported to cause problems in older kernels due to some crypto
drivers having the same name, so revert it here to fix the problems.
Link: https://lore.kernel.org/r/aceda6e2-cefb-4146-aef8-ff4bafa56e56@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ovidiu Panait <ovidiu.panait@windriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54c4ec5f8c471b7c1137a1f769648549c423c026 ]
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147ef6 ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0af4bcb49464c221ad5f95d40f2b1b252ceedcc ]
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
Provide wrapper functions for spin_[un]lock*(port->lock) invocations so
that the console mechanics can be applied later on at a single place and
does not require to copy the same logic all over the drivers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 54c4ec5f8c47 ("serial: mxs-auart: add spinlock around changing cts state")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9e743e923b256e353a9a644195372285e5a6c0 ]
The CPTS, by design, captures the messageType (Sync, Delay_Req, etc.)
field from the second nibble of the PTP header which is defined in the
PTPv2 (1588-2008) specification. In the PTPv1 (1588-2002) specification
the first two bytes of the PTP header are defined as the versionType
which is always 0x0001. This means that any PTPv1 packets that are
tagged for TX timestamping by the CPTS will have their messageType set
to 0x0 which corresponds to a Sync message type. This causes issues
when a PTPv1 stack is expecting a Delay_Req (messageType: 0x1)
timestamp that never appears.
Fix this by checking if the ptp_class of the timestamped TX packet is
PTP_CLASS_V1 and then matching the PTP sequence ID to the stored
sequence ID in the skb->cb data structure. If the sequence IDs match
and the packet is of type PTPv1 then there is a chance that the
messageType has been incorrectly stored by the CPTS so overwrite the
messageType stored by the CPTS with the messageType from the skb->cb
data structure. This allows the PTPv1 stack to receive TX timestamps
for Delay_Req packets which are necessary to lock onto a PTP Leader.
Signed-off-by: Jason Reeder <jreeder@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Ed Trexel <ed.trexel@hp.com>
Fixes: f6bd59526ca5 ("net: ethernet: ti: introduce am654 common platform time sync driver")
Link: https://lore.kernel.org/r/20240424071626.32558-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54976cf58d6168b8d15cebb395069f23b2f34b31 ]
Same number of TCs doesn't imply that underlying TC configs are
same. The config could be different due to difference in number
of queues in each TC. Add utility function to determine if TC
configs are same.
Fixes: d5b33d024496 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Mineri Bhange <minerix.bhange@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240423182723.740401-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef3c313119ea448c22da10366faa26b5b4b1a18e ]
If the MFS is set below the default (0x2600), a warning message is
reported like the following :
MFS for port 1 has been set below the default: 600
This message is a bit confusing as the number shown here (600) is in
fact an hexa number: 0x600 = 1536
Without any explicit "0x" prefix, this message is read like the MFS is
set to 600 bytes.
MFS, as per MTUs, are usually expressed in decimal base.
This commit reports both current and default MFS values in decimal
so it's less confusing for end-users.
A typical warning message looks like the following :
MFS for port 1 (1536) has been set below the default (9728)
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixes: 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set")
Link: https://lore.kernel.org/r/20240423182723.740401-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb4e2b70a7194b209fc7320bbf33b375f7114bd5 ]
The rehash delayed work is rescheduled with a delay if the number of
credits at end of the work is not negative as supposedly it means that
the migration ended. Otherwise, it is rescheduled immediately.
After "mlxsw: spectrum_acl_tcam: Fix possible use-after-free during
rehash" the above is no longer accurate as a non-negative number of
credits is no longer indicative of the migration being done. It can also
happen if the work encountered an error in which case the migration will
resume the next time the work is scheduled.
The significance of the above is that it is possible for the work to be
pending and associated with hints that were allocated when the migration
started. This leads to the hints being leaked [1] when the work is
canceled while pending as part of ACL region dismantle.
Fix by freeing the hints if hints are associated with a work that was
canceled while pending.
Blame the original commit since the reliance on not having a pending
work associated with hints is fragile.
[1]
unreferenced object 0xffff88810e7c3000 (size 256):
comm "kworker/0:16", pid 176, jiffies 4295460353
hex dump (first 32 bytes):
00 30 95 11 81 88 ff ff 61 00 00 00 00 00 00 80 .0......a.......
00 00 61 00 40 00 00 00 00 00 00 00 04 00 00 00 ..a.@...........
backtrace (crc 2544ddb9):
[<00000000cf8cfab3>] kmalloc_trace+0x23f/0x2a0
[<000000004d9a1ad9>] objagg_hints_get+0x42/0x390
[<000000000b143cf3>] mlxsw_sp_acl_erp_rehash_hints_get+0xca/0x400
[<0000000059bdb60a>] mlxsw_sp_acl_tcam_vregion_rehash_work+0x868/0x1160
[<00000000e81fd734>] process_one_work+0x59c/0xf20
[<00000000ceee9e81>] worker_thread+0x799/0x12c0
[<00000000bda6fe39>] kthread+0x246/0x300
[<0000000070056d23>] ret_from_fork+0x34/0x70
[<00000000dea2b93e>] ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1d9 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0cc12ebb07c4d4c41a1265ee2c28b392ff997a86.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b377add0f0117409c418ddd6504bd682ebe0bf79 ]
Both the function that migrates all the chunks within a region and the
function that migrates all the entries within a chunk call
list_first_entry() on the respective lists without checking that the
lists are not empty. This is incorrect usage of the API, which leads to
the following warning [1].
Fix by returning if the lists are empty as there is nothing to migrate
in this case.
[1]
WARNING: CPU: 0 PID: 6437 at drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c:1266 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0>
Modules linked in:
CPU: 0 PID: 6437 Comm: kworker/0:37 Not tainted 6.9.0-rc3-custom-00883-g94a65f079ef6 #39
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0x2c0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x4a0
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 6f9579d4e302 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/4628e9a22d1d84818e28310abbbc498e7bc31bc9.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 743edc8547a92b6192aa1f1b6bb78233fa21dc9b ]
As previously explained, the rehash delayed work migrates filters from
one region to another. This is done by iterating over all chunks (all
the filters with the same priority) in the region and in each chunk
iterating over all the filters.
When the work runs out of credits it stores the current chunk and entry
as markers in the per-work context so that it would know where to resume
the migration from the next time the work is scheduled.
Upon error, the chunk marker is reset to NULL, but without resetting the
entry markers despite being relative to it. This can result in migration
being resumed from an entry that does not belong to the chunk being
migrated. In turn, this will eventually lead to a chunk being iterated
over as if it is an entry. Because of how the two structures happen to
be defined, this does not lead to KASAN splats, but to warnings such as
[1].
Fix by creating a helper that resets all the markers and call it from
all the places the currently only reset the chunk marker. For good
measures also call it when starting a completely new rehash. Add a
warning to avoid future cases.
[1]
WARNING: CPU: 7 PID: 1076 at drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:407 mlxsw_afk_encode+0x242/0x2f0
Modules linked in:
CPU: 7 PID: 1076 Comm: kworker/7:24 Tainted: G W 6.9.0-rc3-custom-00880-g29e61d91b77b #29
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:mlxsw_afk_encode+0x242/0x2f0
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_entry_add+0xd9/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x109/0x290
mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
</TASK>
Fixes: 6f9579d4e302 ("mlxsw: spectrum_acl: Remember where to continue rehash migration")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/cc17eed86b41dd829d39b07906fec074a9ce580e.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca3f7a7b61393804c46f170743c3b839df13977 ]
The rehash delayed work migrates filters from one region to another.
This is done by iterating over all chunks (all the filters with the same
priority) in the region and in each chunk iterating over all the
filters.
If the migration fails, the code tries to migrate the filters back to
the old region. However, the rollback itself can also fail in which case
another migration will be erroneously performed. Besides the fact that
this ping pong is not a very good idea, it also creates a problem.
Each virtual chunk references two chunks: The currently used one
('vchunk->chunk') and a backup ('vchunk->chunk2'). During migration the
first holds the chunk we want to migrate filters to and the second holds
the chunk we are migrating filters from.
The code currently assumes - but does not verify - that the backup chunk
does not exist (NULL) if the currently used chunk does not reference the
target region. This assumption breaks when we are trying to rollback a
rollback, resulting in the backup chunk being overwritten and leaked
[1].
Fix by not rolling back a failed rollback and add a warning to avoid
future cases.
[1]
WARNING: CPU: 5 PID: 1063 at lib/parman.c:291 parman_destroy+0x17/0x20
Modules linked in:
CPU: 5 PID: 1063 Comm: kworker/5:11 Tainted: G W 6.9.0-rc2-custom-00784-gc6a05c468a0b #14
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:parman_destroy+0x17/0x20
[...]
Call Trace:
<TASK>
mlxsw_sp_acl_atcam_region_fini+0x19/0x60
mlxsw_sp_acl_tcam_region_destroy+0x49/0xf0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x1f1/0x470
process_one_work+0x151/0x370
worker_thread+0x2cb/0x3e0
kthread+0xd0/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: 843500518509 ("mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/d5edd4f4503934186ae5cfe268503b16345b4e0f.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bcf925587e9b5d36420d572a0b4d131c90fb306 ]
In the rare cases when the device resources are exhausted it is likely
that the rehash delayed work will fail. An error message will be printed
whenever this happens which can be overwhelming considering the fact
that the work is per-region and that there can be hundreds of regions.
Fix by rate limiting the error message.
Fixes: e5e7962ee5c2 ("mlxsw: spectrum_acl: Implement region migration according to hints")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/c510763b2ebd25e7990d80183feff91cde593145.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54225988889931467a9b55fdbef534079b665519 ]
The rehash delayed work migrates filters from one region to another
according to the number of available credits.
The migrated from region is destroyed at the end of the work if the
number of credits is non-negative as the assumption is that this is
indicative of migration being complete. This assumption is incorrect as
a non-negative number of credits can also be the result of a failed
migration.
The destruction of a region that still has filters referencing it can
result in a use-after-free [1].
Fix by not destroying the region if migration failed.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
Read of size 8 at addr ffff8881735319e8 by task kworker/0:31/3858
CPU: 0 PID: 3858 Comm: kworker/0:31 Tainted: G W 6.9.0-rc2-custom-00782-gf2275c2157d8 #5
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_acl_ctcam_region_entry_remove+0x21d/0x230
mlxsw_sp_acl_ctcam_entry_del+0x2e/0x70
mlxsw_sp_acl_atcam_entry_del+0x81/0x210
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3cd/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 174:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
__kmalloc+0x19c/0x360
mlxsw_sp_acl_tcam_region_create+0xdf/0x9c0
mlxsw_sp_acl_tcam_vregion_rehash_work+0x954/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Freed by task 7:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x102/0x170
__kasan_slab_free+0x14/0x30
kfree+0xc1/0x290
mlxsw_sp_acl_tcam_region_destroy+0x272/0x310
mlxsw_sp_acl_tcam_vregion_rehash_work+0x731/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Fixes: c9c9af91f1d9 ("mlxsw: spectrum_acl: Allow to interrupt/continue rehash work")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/3e412b5659ec2310c5c615760dfe5eac18dd7ebd.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79b5b4b18bc85b19d3a518483f9abbbe6d7b3ba4 ]
The rule activity update delayed work periodically traverses the list of
configured rules and queries their activity from the device.
As part of this task it accesses the entry pointed by 'ventry->entry',
but this entry can be changed concurrently by the rehash delayed work,
leading to a use-after-free [1].
Fix by closing the race and perform the activity query under the
'vregion->lock' mutex.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
Read of size 8 at addr ffff8881054ed808 by task kworker/0:18/181
CPU: 0 PID: 181 Comm: kworker/0:18 Not tainted 6.9.0-rc2-custom-00781-gd5ab772d32f7 #2
Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019
Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_acl_tcam_flower_rule_activity_get+0x121/0x140
mlxsw_sp_acl_rule_activity_update_work+0x219/0x400
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 1039:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
__kmalloc+0x19c/0x360
mlxsw_sp_acl_tcam_entry_create+0x7b/0x1f0
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x30d/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Freed by task 1039:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x102/0x170
__kasan_slab_free+0x14/0x30
kfree+0xc1/0x290
mlxsw_sp_acl_tcam_vchunk_migrate_all+0x3d7/0xb50
mlxsw_sp_acl_tcam_vregion_rehash_work+0x157/0x1300
process_one_work+0x8eb/0x19b0
worker_thread+0x6c9/0xf70
kthread+0x2c9/0x3b0
ret_from_fork+0x4d/0x80
ret_from_fork_asm+0x1a/0x30
Fixes: 2bffc5322fd8 ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1fcce0a60b231ebeb2515d91022284ba7b4ffe7a.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d90cfe20562407d9f080d24123078d666d730707 ]
The purpose of the rehash delayed work is to reduce the number of masks
(eRPs) used by an ACL region as the eRP bank is a global and limited
resource.
This is done in three steps:
1. Creating a new set of masks and a new ACL region which will use the
new masks and to which the existing filters will be migrated to. The
new region is assigned to 'vregion->region' and the region from which
the filters are migrated from is assigned to 'vregion->region2'.
2. Migrating all the filters from the old region to the new region.
3. Destroying the old region and setting 'vregion->region2' to NULL.
Only the second steps is performed under the 'vregion->lock' mutex
although its comments says that among other things it "Protects
consistency of region, region2 pointers".
This is problematic as the first step can race with filter insertion
from user space that uses 'vregion->region', but under the mutex.
Fix by holding the mutex across the entirety of the delayed work and not
only during the second step.
Fixes: 2bffc5322fd8 ("mlxsw: spectrum_acl: Don't take mutex in mlxsw_sp_acl_tcam_vregion_rehash_work()")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1ec1d54edf2bad0a369e6b4fa030aba64e1f124b.1713797103.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ea7b72d4fac2fdbc0425cd8f2ea33abe95235b2 ]
Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal
of ovs_ct_limit_exit, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 11efd5cb04a1 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/ZiYvzQN/Ry5oeFQW@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e10d3ba4d434ed172914617ed8d74bd411421193 ]
It was observed in the wild that pairs of consecutive packets would leave
the IPVS with the same wrong checksum, and the issue only went away when
disabling GSO.
IPVS needs to avoid computing the SCTP checksum when using GSO.
Fixes: 90017accff61 ("sctp: Add GSO support")
Co-developed-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: Ismael Luceno <iluceno@suse.de>
Tested-by: Andreas Taschner <andreas.taschner@suse.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2a904107ee2b647bb7794a1a82b67740d7c8a64 ]
Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal
of gtp_dellink, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 94dc550a5062 ("gtp: fix an use-after-free in ipv4_pdp_find()")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ce62d5b2f7aecd4900e7d6115588ad7f9acccca ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize overide.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path")
Fixes: f8ebb3ac881b ("net: usb: ax88179_178a: Fix packet receiving")
Reported-by: shironeko <shironeko@tesaguri.club>
Closes: https://lore.kernel.org/netdev/c110f41a0d2776b525930f213ca9715c@tesaguri.club/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jose Alonso <joalonsof@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240421193828.1966195-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bea4f03c6a4e973ef369e15aac88f37981db49e ]
During module probe, regulator 'vin' and 'vdd-io' are used and enabled,
but the vdd-io regulator overwrites the 'vin' regulator pointer. During
remove, only the vdd-io is disabled, as the vin regulator pointer is not
available anymore. When regulator_put() is called during resource
cleanup a kernel warning is given, as the regulator is still enabled.
Store the two regulators in separate pointers and disable both the
regulators on module remove.
Fixes: 49d22c70aaf0 ("NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/DB7PR09MB26847A4EBF88D9EDFEB1DA0F950E2@DB7PR09MB2684.eurprd09.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976c44af48141cd8595601c0af2a19a43c5b228b ]
The device's manual (PRM - Programmer's Reference Manual) classifies the
trap that is used to deliver EMAD responses as an "event trap". Among
other things, it means that the only actions that can be associated with
the trap are TRAP and FORWARD (NOP).
Currently, during driver de-initialization the driver unregisters the
trap by setting its action to DISCARD, which violates the above
guideline. Future firmware versions will prevent such misuses by
returning an error. This does not prevent the driver from working, but
an error will be printed to the kernel log during module removal /
devlink reload:
mlxsw_spectrum 0000:03:00.0: Reg cmd access status failed (status=7(bad parameter))
mlxsw_spectrum 0000:03:00.0: Reg cmd access failed (reg_id=7003(hpkt),type=write)
Suppress the error message by aligning the driver to the manual and use
a FORWARD (NOP) action when unregistering the trap.
Fixes: 4ec14b7634b2 ("mlxsw: Add interface to access registers and process events")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/753a89e14008fde08cb4a2c1e5f537b81d8eb2d6.1713446092.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f58f45c1e5b92975e91754f5407250085a6ae7cf ]
The VXLAN driver currently does not check if the inner layer2
source-address is valid.
In case source-address snooping/learning is enabled, a entry in the FDB
for the invalid address is created with the layer3 address of the tunnel
endpoint.
If the frame happens to have a non-unicast address set, all this
non-unicast traffic is subsequently not flooded to the tunnel network
but sent to the learnt host in the FDB. To make matters worse, this FDB
entry does not expire.
Apply the same filtering for packets as it is done for bridges. This not
only drops these invalid packets but avoids them from being learnt into
the FDB.
Fixes: d342894c5d2f ("vxlan: virtual extensible lan")
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbfff5bf9292714f02ace002fea8ce6599ea1145 ]
If a PASN station is added, and an old PASN station already exists
for the same mac address, remove the old station before adding the
new one. Keeping the old station caueses old security context to
be used in measurements.
Fixes: 0739a7d70e00 ("iwlwifi: mvm: initiator: add option for adding a PASN responder")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415114847.ef3544a416f2.I4e8c7c8ca22737f4f908ae5cd4fc0b920c703dd3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61231eb8113ce47991f35024f9c20810b37996bf ]
"gmac" node stands for just an ordinary Ethernet controller,
which is by no means a provider of interrupts, i.e. it doesn't serve
as an interrupt controller, thus "#interrupt-cells" property doesn't
belong to it and so we remove it.
Fixes:
------------>8------------
DTC arch/arc/boot/dts/hsdk.dtb
arch/arc/boot/dts/hsdk.dts:207.23-235.5: Warning (interrupt_provider): /soc/ethernet@8000: '#interrupt-cells' found, but node is not an interrupt provider
arch/arc/boot/dts/hsdk.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
------------>8------------
Reported-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4a7dc9523b59b3e73fd522c73e95e072f876b16 upstream.
The size of the nilfs_type_by_mode array in the fs/nilfs2/dir.c file is
defined as "S_IFMT >> S_SHIFT", but the nilfs_set_de_type() function,
which uses this array, specifies the index to read from the array in the
same way as "(mode & S_IFMT) >> S_SHIFT".
static void nilfs_set_de_type(struct nilfs_dir_entry *de, struct inode
*inode)
{
umode_t mode = inode->i_mode;
de->file_type = nilfs_type_by_mode[(mode & S_IFMT)>>S_SHIFT]; // oob
}
However, when the index is determined this way, an out-of-bounds (OOB)
error occurs by referring to an index that is 1 larger than the array size
when the condition "mode & S_IFMT == S_IFMT" is satisfied. Therefore, a
patch to resize the nilfs_type_by_mode array should be applied to prevent
OOB errors.
Link: https://lkml.kernel.org/r/20240415182048.7144-1-konishi.ryusuke@gmail.com
Reported-by: syzbot+2e22057de05b9f3b30d8@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2e22057de05b9f3b30d8
Fixes: 2ba466d74ed7 ("nilfs2: directory entry operations")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fff1386cc889d8fb4089d285f883f8cba62d82ce upstream.
Running a lot of VK CTS in parallel against nouveau, once every
few hours you might see something like this crash.
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ #27
Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021
RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1
RSP: 0000:ffffac20c5857838 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001
RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180
RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10
R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c
R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c
FS: 00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
...
? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau]
? gp100_vmm_pgt_mem+0x37/0x180 [nouveau]
nvkm_vmm_iter+0x351/0xa20 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
? __lock_acquire+0x3ed/0x2170
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau]
? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau]
? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau]
nvkm_vmm_map_locked+0x224/0x3a0 [nouveau]
Adding any sort of useful debug usually makes it go away, so I hand
wrote the function in a line, and debugged the asm.
Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in
the nv50_instobj_acquire called from nvkm_kmap.
If Thread A and Thread B both get to nv50_instobj_acquire around
the same time, and Thread A hits the refcount_set line, and in
lockstep thread B succeeds at refcount_inc_not_zero, there is a
chance the ptrs value won't have been stored since refcount_set
is unordered. Force a memory barrier here, I picked smp_mb, since
we want it on all CPUs and it's write followed by a read.
v2: use paired smp_rmb/smp_wmb.
Cc: <stable@vger.kernel.org>
Fixes: be55287aa5ba ("drm/nouveau/imem/nv50: embed nvkm_instobj directly into nv04_instobj")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240411011510.2546857-1-airlied@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fef2d4c00b5b8561ad68dd2b68173f5c6af1e75 upstream.
Verify the parameters of
amdgpu_vm_bo_(map/replace_map/clearing_mappings) in one common place.
Fixes: dc54d3d1744d ("drm/amdgpu: implement AMDGPU_VA_OP_CLEAR v2")
Cc: stable@vger.kernel.org
Reported-by: Vlad Stolyarov <hexed@google.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46dad3c1e57897ab9228332f03e1c14798d2d3b9 upstream.
We allocate memory of size 'xlen + strlen(boot_command_line) + 1' for
static_command_line, but the strings copied into static_command_line are
extra_command_line and command_line, rather than extra_command_line and
boot_command_line.
When strlen(command_line) > strlen(boot_command_line), static_command_line
will overflow.
This patch just recovers strlen(command_line) which was miss-consolidated
with strlen(boot_command_line) in the commit f5c7310ac73e ("init/main: add
checks for the return value of memblock_alloc*()")
Link: https://lore.kernel.org/all/20240412081733.35925-2-ytcoode@gmail.com/
Fixes: f5c7310ac73e ("init/main: add checks for the return value of memblock_alloc*()")
Cc: stable@vger.kernel.org
Signed-off-by: Yuntao Wang <ytcoode@gmail.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a90bca2228c0646fc29a72689d308e5fe03e6d78 upstream.
The sysfs_break_active_protection() routine has an obvious reference
leak in its error path. If the call to kernfs_find_and_get() fails then
kn will be NULL, so the companion sysfs_unbreak_active_protection()
routine won't get called (and would only cause an access violation by
trying to dereference kn->parent if it was called). As a result, the
reference to kobj acquired at the start of the function will never be
released.
Fix the leak by adding an explicit kobject_put() call when kn is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 2afc9166f79b ("scsi: sysfs: Introduce sysfs_{un,}break_active_protection()")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/8a4d3f0f-c5e3-4b70-a188-0ca433f9e6f9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8d2f34ea96ea3bce6ba2535f867f0d4ee3b22e1 upstream.
In case a console is set up really large and contains a really long word
(> 256 characters), we have to stop before the length of the word buffer.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Fixes: c6e3fd22cd538 ("Staging: add speakup to the staging directory")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240323164843.1426997-1-samuel.thibault@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dc04112bee6fdd6eb847ccb32214703022c0269 upstream.
Extend the quirk to disable MEI interface on Intel PCH Ignition (IGN)
and SPS firmwares for RPL-S devices. These firmwares do not support
the MEI protocol.
Fixes: 3ed8c7d39cfe ("mei: me: add raptor lake point S DID")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240312051958.118478-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d920a2ed8620be04a3301e1a9c2b7cc1de65f19d upstream.
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1607830dadeefc407e4956336d9fcd9e9defd810 upstream.
This reverts commit 339f83612f3a569b194680768b22bf113c26a29d.
It has been found to cause problems in a number of Chromebook devices,
so revert the change until it can be brought back in a safe way.
Link: https://lore.kernel.org/r/385a3519-b45d-48c5-a6fd-a3fdb6bec92f@chromium.org
Reported-by:: Aleksander Morgado <aleksandermj@chromium.org>
Fixes: 339f83612f3a ("usb: cdc-wdm: close race between read and workqueue")
Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1be3226445362bfbf461c92a5bcdb1723f2e4907 upstream.
The mitigation was intended to stop the irq completely. That may be
better than a hard lock-up but it turns out that you get a crash anyway
if you're using pmac_zilog as a serial console:
ttyPZ0: pmz: rx irq flood !
BUG: spinlock recursion on CPU#0, swapper/0
That's because the pr_err() call in pmz_receive_chars() results in
pmz_console_write() attempting to lock a spinlock already locked in
pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal
BUG splat. The spinlock in question is the one in struct uart_port.
Even when it's not fatal, the serial port rx function ceases to work.
Also, the iteration limit doesn't play nicely with QEMU, as can be
seen in the bug report linked below.
A web search for other reports of the error message "pmz: rx irq flood"
didn't produce anything. So I don't think this code is needed any more.
Remove it.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@kernel.org
Cc: linux-m68k@lists.linux-m68k.org
Link: https://github.com/vivier/qemu-m68k/issues/44
Link: https://lore.kernel.org/all/1078874617.9746.36.camel@gaston/
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/e853cf2c762f23101cd2ddec0cc0c2be0e72685f.1712568223.git.fthain@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1718530e3f640b7d5f0050e725216eab57a85d8 upstream.
While vmk80xx does have endpoint checking implemented, some things
can fall through the cracks. Depending on the hardware model,
URBs can have either bulk or interrupt type, and current version
of vmk80xx_find_usb_endpoints() function does not take that fully
into account. While this warning does not seem to be too harmful,
at the very least it will crash systems with 'panic_on_warn' set on
them.
Fix the issue found by Syzkaller [1] by somewhat simplifying the
endpoint checking process with usb_find_common_endpoints() and
ensuring that only expected endpoint types are present.
This patch has not been tested on real hardware.
[1] Syzkaller report:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 781 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
Call Trace:
<TASK>
usb_start_wait_urb+0x113/0x520 drivers/usb/core/message.c:59
vmk80xx_reset_device drivers/comedi/drivers/vmk80xx.c:227 [inline]
vmk80xx_auto_attach+0xa1c/0x1a40 drivers/comedi/drivers/vmk80xx.c:818
comedi_auto_config+0x238/0x380 drivers/comedi/drivers.c:1067
usb_probe_interface+0x5cd/0xb00 drivers/usb/core/driver.c:399
...
Similar issue also found by Syzkaller:
Link: https://syzkaller.appspot.com/bug?extid=5205eb2f17de3e01946e
Reported-and-tested-by: syzbot+5f29dc6a889fc42bd896@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Fixes: 49253d542cc0 ("staging: comedi: vmk80xx: factor out usb endpoint detection")
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20240408171633.31649-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c38fa07dc69f0b9e6f43ecab96dc7861a70c827c upstream.
Currently we don't configure correctly the wake events after unplug of device
router. What can happen is that the downstream ports of host router will be
configured to wake on: USB4-wake and wake-on-disconnect, but not on
wake-on-connect. This may cause the later plugged device not to wake the
domain and fail in enumeration. Fix this by clearing downstream port's "USB4
Port is Configured" bit, after unplug of a device router.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd12acaf384c30437fa5a9a1f71df06fc9835fd upstream.
Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).
While there add the missing kernel-doc for tb_switch_resume().
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaef73821a3b0194a01bd23ca77774f704a04d40 upstream.
Commit 6d98eb95b450 ("binder: avoid potential data leakage when copying
txn") introduced changes to how binder objects are copied. In doing so,
it unintentionally removed an offset alignment check done through calls
to binder_alloc_copy_from_buffer() -> check_buffer().
These calls were replaced in binder_get_object() with copy_from_user(),
so now an explicit offset alignment check is needed here. This avoids
later complications when unwinding the objects gets harder.
It is worth noting this check existed prior to commit 7a67a39320df
("binder: add function to copy binder object from buffer"), likely
removed due to redundancy at the time.
Fixes: 6d98eb95b450 ("binder: avoid potential data leakage when copying txn")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20240330190115.1877819-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9543f6e26634537997b6e909c20911b7bf4876de ]
Fix cpuid_deps[] to list the correct dependencies for GFNI, VAES, and
VPCLMULQDQ. These features don't depend on AVX512, and there exist CPUs
that support these features but not AVX512. GFNI actually doesn't even
depend on AVX.
This prevents GFNI from being unnecessarily disabled if AVX is disabled
to mitigate the GDS vulnerability.
This also prevents all three features from being unnecessarily disabled
if AVX512VL (or its dependency AVX512F) were to be disabled, but it
looks like there isn't any case where this happens anyway.
Fixes: c128dbfa0f87 ("x86/cpufeatures: Enable new SSE/AVX/AVX512 CPU features")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20240417060434.47101-1-ebiggers@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e581cf5d216289ef292d1a4036d53ce90e122469 ]
Doug reported [1] the following hung task:
INFO: task swapper/0:1 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00000008
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
rpm_resume+0xe0/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
clk_pm_runtime_get+0x30/0xb0
clk_disable_unused_subtree+0x58/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused+0x4c/0xe4
do_one_initcall+0xcc/0x2d8
do_initcall_level+0xa4/0x148
do_initcalls+0x5c/0x9c
do_basic_setup+0x24/0x30
kernel_init_freeable+0xec/0x164
kernel_init+0x28/0x120
ret_from_fork+0x10/0x20
INFO: task kworker/u16:0:9 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack: 0 pid: 9 ppid: 2 flags:0x00000008
Workqueue: events_unbound deferred_probe_work_func
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
schedule_preempt_disabled+0x2c/0x48
__mutex_lock+0x238/0x488
__mutex_lock_slowpath+0x1c/0x28
mutex_lock+0x50/0x74
clk_prepare_lock+0x7c/0x9c
clk_core_prepare_lock+0x20/0x44
clk_prepare+0x24/0x30
clk_bulk_prepare+0x40/0xb0
mdss_runtime_resume+0x54/0x1c8
pm_generic_runtime_resume+0x30/0x44
__genpd_runtime_resume+0x68/0x7c
genpd_runtime_resume+0x108/0x1f4
__rpm_callback+0x84/0x144
rpm_callback+0x30/0x88
rpm_resume+0x1f4/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
__device_attach+0xe0/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
device_add+0x644/0x814
mipi_dsi_device_register_full+0xe4/0x170
devm_mipi_dsi_device_register_full+0x28/0x70
ti_sn_bridge_probe+0x1dc/0x2c0
auxiliary_bus_probe+0x4c/0x94
really_probe+0xcc/0x2c8
__driver_probe_device+0xa8/0x130
driver_probe_device+0x48/0x110
__device_attach_driver+0xa4/0xcc
bus_for_each_drv+0x8c/0xd8
__device_attach+0xf8/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
deferred_probe_work_func+0x9c/0xd8
process_one_work+0x148/0x518
worker_thread+0x138/0x350
kthread+0x138/0x1e0
ret_from_fork+0x10/0x20
The first thread is walking the clk tree and calling
clk_pm_runtime_get() to power on devices required to read the clk
hardware via struct clk_ops::is_enabled(). This thread holds the clk
prepare_lock, and is trying to runtime PM resume a device, when it finds
that the device is in the process of resuming so the thread schedule()s
away waiting for the device to finish resuming before continuing. The
second thread is runtime PM resuming the same device, but the runtime
resume callback is calling clk_prepare(), trying to grab the
prepare_lock waiting on the first thread.
This is a classic ABBA deadlock. To properly fix the deadlock, we must
never runtime PM resume or suspend a device with the clk prepare_lock
held. Actually doing that is near impossible today because the global
prepare_lock would have to be dropped in the middle of the tree, the
device runtime PM resumed/suspended, and then the prepare_lock grabbed
again to ensure consistency of the clk tree topology. If anything
changes with the clk tree in the meantime, we've lost and will need to
start the operation all over again.
Luckily, most of the time we're simply incrementing or decrementing the
runtime PM count on an active device, so we don't have the chance to
schedule away with the prepare_lock held. Let's fix this immediate
problem that can be triggered more easily by simply booting on Qualcomm
sc7180.
Introduce a list of clk_core structures that have been registered, or
are in the process of being registered, that require runtime PM to
operate. Iterate this list and call clk_pm_runtime_get() on each of them
without holding the prepare_lock during clk_disable_unused(). This way
we can be certain that the runtime PM state of the devices will be
active and resumed so we can't schedule away while walking the clk tree
with the prepare_lock held. Similarly, call clk_pm_runtime_put() without
the prepare_lock held to properly drop the runtime PM reference. We
remove the calls to clk_pm_runtime_{get,put}() in this path because
they're superfluous now that we know the devices are runtime resumed.
Reported-by: Douglas Anderson <dianders@chromium.org>
Closes: https://lore.kernel.org/all/20220922084322.RFC.2.I375b6b9e0a0a5348962f004beb3dafee6a12dfbb@changeid/ [1]
Closes: https://issuetracker.google.com/328070191
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9a34b45397e5 ("clk: Add support for runtime PM")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-5-sboyd@kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman