[ Upstream commit 3f42b142ea1171967e40e10e4b0241c0d6d28d41 ]
After upgrading from 5.16 to 6.1, our board with a MAX14830 started
producing lots of garbage data over UART. Bisection pointed out commit
285e76fc049c as the culprit. That patch tried to replace hand-written
code which I added in 2b4bac48c1084 ("serial: max310x: Use batched reads
when reasonably safe") with the generic regmap infrastructure for
batched operations.
Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were
used are actually functions which perform IO over *multiple* registers.
That's not what is needed for accessing these Tx/Rx FIFOs; the
appropriate functions are the `_noinc_` versions, not the `_raw_` ones.
Fix this regression by using `regmap_noinc_read()` and
`regmap_noinc_write()` along with the necessary `regmap_config` setup;
with this patch in place, our board communicates happily again. Since
our board uses SPI for talking to this chip, the I2C part is completely
untested.
Fixes: 285e76fc049c ("serial: max310x: use regmap methods for SPI batch operations")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e1f2d9a9bdbe12ee475c82a45ac46a278e8049a ]
I2C implementation on this chip has a few key differences
compared to SPI, as described in previous patches.
* extended register space access needs no extra logic
* slave address is used to select which UART to communicate
with
To accommodate these differences, add an I2C interface config,
set the RevID register address and implement an empty method
for setting the GlobalCommand register, since no special handling
is needed for the extended register space.
To handle the port-specific slave address, create an I2C dummy
device for each port, except the base one (UART0), which is
expected to be the one specified in firmware, and create a
regmap for each I2C device.
Add minimum and maximum slave addresses to each devtype for
sanity checking.
Also, use a separate regmap config with no write_flag_mask,
since I2C has a R/W bit in its slave address, and set the
max register to the address of the RevID register, since the
extended register space needs no extra logic.
Finally, add the I2C driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-5-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3f42b142ea11 ("serial: max310x: fix IO data corruption in batched operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3883ab5e95713e479f774ea68be275413e8e5b2 ]
SPI can only use 5 address bits, since one bit is reserved for
specifying R/W and 2 bits are used to specify the UART port.
To access registers that have addresses past 0x1F, an extended
register space can be enabled by writing to the GlobalCommand
register (address 0x1F).
I2C uses 8 address bits. The R/W bit is placed in the slave
address, and so is the UART port. Because of this, registers
that have addresses higher than 0x1F can be accessed normally.
To access the RevID register, on SPI, 0xCE must be written to
the 0x1F address to enable the extended register space, after
which the RevID register is accessible at address 0x5. 0xCD
must be written to the 0x1F address to disable the extended
register space.
On I2C, the RevID register is accessible at address 0x25.
Create an interface config struct, and add a method for
toggling the extended register space and a member for the RevId
register address. Implement these for SPI.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-4-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3f42b142ea11 ("serial: max310x: fix IO data corruption in batched operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61acabaae5ba58b3c32e6e90d24c2c0827fd27a8 ]
In one error case the clock may be left prepared and enabled.
Unprepare and disable clock in that case to balance state of
the hardware.
Fixes: d4d6f03c4fb3 ("serial: max310x: Try to get crystal clock rate from property")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210625153733.12911-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b35f8dbbce818b02c730dc85133dc7754266e084 ]
If there is a problem after resetting a port, the do/while() loop that
checks the default value of DIVLSB register may run forever and spam the
I2C bus.
Add a delay before each read of DIVLSB, and a maximum number of tries to
prevent that situation from happening.
Also fail probe if port reset is unsuccessful.
Fixes: 10d8b34a4217 ("serial: max310x: Driver rework")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ef281daf020592c219fa91780abc381c6c20db5 ]
The driver currently does manual register manipulation in
multiple places to talk to a specific UART port.
In order to talk to a specific UART port over SPI, the bits U1
and U0 of the register address can be set, as explained in the
Command byte configuration section of the datasheet.
Make this more elegant by creating regmaps for each UART port
and setting the read_flag_mask and write_flag_mask
accordingly.
All communcations regarding global registers are done on UART
port 0, so replace the global regmap entirely with the port 0
regmap.
Also, remove the 0x1f masks from reg_writeable(), reg_volatile()
and reg_precious() methods, since setting the U1 and U0 bits of
the register address happens inside the regmap core now.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-3-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b35f8dbbce81 ("serial: max310x: prevent infinite while() loop in port startup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285e76fc049c4d32c772eea9460a7ef28a193802 ]
The SPI batch read/write operations can be implemented as simple
regmap raw read and write, which will also try to do a gather
write just as it is done here.
Use the regmap raw read and write methods.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-2-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b35f8dbbce81 ("serial: max310x: prevent infinite while() loop in port startup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c808fab604ca62cff19ee6b261211483830807aa ]
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201007084635.594991-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b35f8dbbce81 ("serial: max310x: prevent infinite while() loop in port startup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8afa6c6decea37e7cb473d2c60473f37f46cea35 ]
A stable clock is really required in order to use this UART, so log an
error message and bail out if the chip reports that the clock is not
stable.
Fixes: 4cf9a888fd3c ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Suggested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://www.spinics.net/lists/linux-serial/msg35773.html
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4d6f03c4fb3a91dadfe147b47edd40e4d7e4d36 ]
In some configurations, mainly ACPI-based, the clock frequency of the device
is supplied by very well established 'clock-frequency' property. Hence, try
to get it from the property at last if no other providers are available.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210517172930.83353-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8afa6c6decea ("serial: max310x: fail probe if clock crystal is unstable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 974e454d6f96da0c0ab1b4115b92587dd9406f6a ]
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). If no input clock is present
devm_clk_get_optional() will return NULL instead of an error
which matches the behavior of the old code.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201007084635.594991-2-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8afa6c6decea ("serial: max310x: fail probe if clock crystal is unstable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6214894f49a967c749ee6c07cb00f9cede748df4 ]
The hvc machinery registers both a console and a tty device based on
the hv ops provided by the specific implementation. Those two
interfaces however have different locks, and there's no single locks
that's shared between the tty and the console implementations, hence
the driver needs to protect itself against concurrent accesses.
Otherwise concurrent calls using the split interfaces are likely to
corrupt the ring indexes, leaving the console unusable.
Introduce a lock to xencons_info to serialize accesses to the shared
ring. This is only required when using the shared memory console,
concurrent accesses to the hypercall based console implementation are
not an issue.
Note the conditional logic in domU_read_console() is slightly modified
so the notify_daemon() call can be done outside of the locked region:
it's an hypercall and there's no need for it to be done with the lock
held.
Fixes: b536b4b96230 ('xen: use the hvc console infrastructure for Xen console')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20221130150919.13935-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c2a5f471ce58bca8f8ab5fcb911aff91eaaa5eb ]
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8925c31c1ac2f1e05da988581f2a70a2a8c4d638 ]
Preparing to move serial_rs485 struct sanitization into serial core,
each driver has to provide what fields/flags it supports. This
information is pointed into by rs485_supported.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 0c2a5f471ce5 ("serial: 8250_exar: Set missing rs485_supported flag")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 93cd256ab224c2519e7c4e5f58bb4f1ac2bf0965 upstream.
Some people are seeing a warning similar to this when using a crystal:
max310x 11-006c: clock is not stable yet
The datasheet doesn't mention the maximum time to wait for the clock to be
stable when using a crystal, and it seems that the 10ms delay in the driver
is not always sufficient.
Jan Kundrát reported that it took three tries (each separated by 10ms) to
get a stable clock.
Modify behavior to check stable clock ready bit multiple times (20), and
waiting 10ms between each try.
Note: the first draft of the driver originally used a 50ms delay, without
checking the clock stable bit.
Then a loop with 1000 retries was implemented, each time reading the clock
stable bit.
Fixes: 4cf9a888fd3c ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Suggested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://www.spinics.net/lists/linux-serial/msg35773.html
Link: https://lore.kernel.org/all/20240110174015.6f20195fde08e5c9e64e5675@hugovil.com/raw
Link: e5dfe3e4a7
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0419373333c2f2024966d36261fd82a453281e80 upstream.
If regmap_read() returns a non-zero value, the 'val' variable can be left
uninitialized.
Clear it before calling regmap_read() to make sure we properly detect
the clock ready bit.
Fixes: 4cf9a888fd3c ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e0f25b8992345aa5f113da2815f5add98738c611 ]
The capability CAP_CHECKPOINT_RESTORE was introduced to allow non-root
users to checkpoint and restore processes as non-root with CRIU.
This change extends CAP_CHECKPOINT_RESTORE to enable the CRIU option
'--shell-job' as non-root. CRIU's man-page describes the '--shell-job'
option like this:
Allow one to dump shell jobs. This implies the restored task will
inherit session and process group ID from the criu itself. This option
also allows to migrate a single external tty connection, to migrate
applications like top.
TIOCSLCKTRMIOS can only be done if the process has CAP_SYS_ADMIN and
this change extends it to CAP_SYS_ADMIN or CAP_CHECKPOINT_RESTORE.
With this change it is possible to checkpoint and restore processes
which have a tty connection as non-root if CAP_CHECKPOINT_RESTORE is
set.
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Adrian Reber <areber@redhat.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
Link: https://lore.kernel.org/r/20231208143656.1019-1-areber@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d710b769c1f5f0d55c9ad9bb49b7dce009ec103 ]
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ef79cd1412236d884ab0c46b4d1921380807b48 ]
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66aad7d8d3ec5a3a8ec2023841bcec2ded5f65c9 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7bb94 ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24f2cd019946fc2e88e632d2e24a34c2cc3f2be4 ]
Now, the "jumped-over" code is simple enough to be put inside an 'if'.
Do so to make it 'goto'-less.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd99392b643b824813df2edbaebe26a2136d31e6 ]
msleep_interruptible() will check on its own. So no need to do the check
in send_break() before calling the above.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66619686d187b4a6395316b7f39881e945dce4bc ]
If the driver sets TTY_DRIVER_HARDWARE_BREAK, we leave ops->break_ctl()
to the driver and return from send_break(). But we do it using a local
variable and keep the code flowing through the end of the function.
Instead, do 'return' immediately with the ops->break_ctl()'s return
value.
This way, we don't have to stuff the 'else' branch of the 'if' with the
software break handling. And we can re-indent the function too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78d60dae9a0c9f09aa3d6477c94047df2fe6f7b0 ]
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Fixes: cb1a60923609 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad90d0358bd3b4554f243a425168fc7cebe7d04e ]
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow. So all resources that were not freed
are leaked in this case. Skipping serial8250_unregister_port() has the
potential to keep enough of the UART around to trigger a use-after-free.
So replace the error return (and with it the little helpful error
message) by a more useful error message and continue to cleanup.
Fixes: e3f0c638f428 ("serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231110152927.70601-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7c45eaa813476bd195ac1227a64b52f9cf2e2030 upstream.
There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986e6 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.
Fixes: 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16c6d2e58a4c2b972efcf9eb12390ee0ba3befb upstream
A null pointer dereference can happen when attempting to access the
"gsm->receive()" function in gsmld_receive_buf(). Currently, the code
assumes that gsm->receive is only called after MUX activation.
Since the gsmld_receive_buf() function can be accessed without the need to
initialize the MUX, the gsm->receive() function will not be set and a
NULL pointer dereference will occur.
Fix this by avoiding the call to "gsm->receive()" in case the function is
not initialized by adding a sanity check.
Call Trace:
<TASK>
gsmld_receive_buf+0x1c2/0x2f0 drivers/tty/n_gsm.c:2861
tiocsti drivers/tty/tty_io.c:2293 [inline]
tty_ioctl+0xa75/0x15d0 drivers/tty/tty_io.c:2692
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Link: https://syzkaller.appspot.com/bug?id=bdf035c61447f8c6e0e6920315d577cb5cc35ac5
Fixes: 01aecd917114 ("tty: n_gsm: fix tty registration before control channel open")
Reported-and-tested-by: syzbot+e3563f0c94e188366dbb@syzkaller.appspotmail.com
Signed-off-by: Mazin Al Haddad <mazinalhaddad05@gmail.com>
Link: https://lore.kernel.org/r/20220814015211.84180-1-mazinalhaddad05@gmail.com
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b93db97e1ca08e500305bc46b08c72e2232c4be1 upstream.
dp, f, and i are only duplicates of gsmld_receive_buf's parameters. Use
the parameters directly (cp, fp, and count) and delete these local
variables.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-41-jslaby@suse.cz
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01aecd917114577c423f07cec0d186ad007d76fc upstream.
The current implementation registers/deregisters the user ttys at mux
attach/detach. That means that the user devices are available before any
control channel is open. However, user channel initialization requires an
open control channel. Furthermore, the user is not informed if the mux
restarts due to configuration changes.
Put the registration/deregistration procedure into separate function to
improve readability.
Move registration to mux activation and deregistration to mux cleanup to
keep the user devices only open as long as a control channel exists. The
user will be informed via the device driver if the mux was reconfigured in
a way that required a mux re-activation.
This makes it necessary to add T2 initialization to gsmld_open() for the
ldisc open code path (not the reconfiguration code path) to avoid deletion
of an uninitialized T2 at mux cleanup.
Fixes: d50f6dcaf22a ("tty: n_gsm: expose gsmtty device nodes at ldisc open time")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-2-daniel.starke@siemens.com
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e42c301ce64e0dcca547626eb486877d502d336 upstream.
Currently there is no support for earlycon on the AM654 UART
controller. This commit adds it.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031131242.15516-1-rwahl@gmx.de
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6bb057418876cdfdd29a6f7b8cef54539ee8811 upstream.
Starting RX DMA on THRI interrupt is too early because TX may not have
finished yet.
This change is inspired by commit 90b8596ac460 ("serial: 8250: Prevent
starting up DMA Rx on THRI interrupt") and fixes DMA issues I had with
an AM62 SoC that is using the 8250 OMAP variant.
Cc: stable@vger.kernel.org
Fixes: c26389f998a8 ("serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231101171431.16495-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8973ab7a2441b286218f4a5c4c33680e2f139996 upstream.
This fixes commit 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX
interrupt after DMA enable") which unfortunately set the
UART_HAS_RHR_IT_DIS bit in the UART_OMAP_IER2 register and never
cleared it.
Cc: stable@vger.kernel.org
Fixes: 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031110909.11695-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08ce9a1b72e38cf44c300a44ac5858533eb3c860 upstream.
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58ac1b3799799069d53f5bf95c093f2fe8dd3cc5 upstream.
Since there is no guarantee that the memory returned by
dma_alloc_coherent() is associated with a 'struct page', using the
architecture specific phys_to_page() is wrong, but using
virt_to_page() would be as well.
Stop using sg lists altogether and just use the *_single() functions
instead. This also simplifies the code a bit since the scatterlists in
this driver always have only one entry anyway.
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
gc: Add a commit log from the initial thread:
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
Fixes: cb06ff102e2d7 ("ARM: PL011: Add support for Rx DMA buffer polling.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231122171503.235649-1-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b68061983471470d4109bac776145245f06bc09 ]
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2a1d728f20ed ("tty: serial: meson: fix hard LOCKUP on crtscts mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27d44e05d7b85d9d4cfe0a3c0663ea49752ece93 ]
Now the DT bindings has a property to get the FIFO size for a particular port,
retrieve it and use to setup the FIFO interrupts threshold.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210518075833.3736038-3-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2a1d728f20ed ("tty: serial: meson: fix hard LOCKUP on crtscts mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 021212f5335229ed12e3d31f9b7d30bd3bb66f7d ]
The variable id being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed. Since id is just being used in a for-loop
inside a local scope, move the declaration of id to that scope.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210426101106.9122-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2a1d728f20ed ("tty: serial: meson: fix hard LOCKUP on crtscts mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2704c9a5593f4a47620c12dad78838ca62b52f48 upstream.
The xen_hvc_init() function should always register the frontend driver,
even when there's no primary console — as there may be secondary consoles.
(Qemu can always add secondary consoles, but only the toolstack can add
the primary because it's special.)
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-3-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30badfd7c13fc8763a9e10c5a12ba7f81515a55 upstream.
On unplug of a Xen console, xencons_disconnect_backend() unconditionally
calls free_irq() via unbind_from_irqhandler(), causing a warning of
freeing an already-free IRQ:
(qemu) device_del con1
[ 32.050919] ------------[ cut here ]------------
[ 32.050942] Trying to free already-free IRQ 33
[ 32.050990] WARNING: CPU: 0 PID: 51 at kernel/irq/manage.c:1895 __free_irq+0x1d4/0x330
It should be using evtchn_put() to tear down the event channel binding,
and let the Linux IRQ side of it be handled by notifier_del_irq() through
the HVC code.
On which topic... xencons_disconnect_backend() should call hvc_remove()
*first*, rather than tearing down the event channel and grant mapping
while they are in use. And then the IRQ is guaranteed to be freed by
the time it's torn down by evtchn_put().
Since evtchn_put() also closes the actual event channel, avoid calling
xenbus_free_evtchn() except in the failure path where the IRQ was not
successfully set up.
However, calling hvc_remove() at the start of xencons_disconnect_backend()
still isn't early enough. An unplug request is indicated by the backend
setting its state to XenbusStateClosing, which triggers a notification
to xencons_backend_changed(), which... does nothing except set its own
frontend state directly to XenbusStateClosed without *actually* tearing
down the HVC device or, you know, making sure it isn't actively in use.
So the backend sees the guest frontend set its state to XenbusStateClosed
and stops servicing the interrupt... and the guest spins for ever in the
domU_write_console() function waiting for the ring to drain.
Fix that one by calling hvc_remove() from xencons_backend_changed() before
signalling to the backend that it's OK to proceed with the removal.
Tested with 'dd if=/dev/zero of=/dev/hvc1' while telling Qemu to remove
the console device.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-4-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd976a97d15b47656991e185a94ef42a0fa5cfd4 upstream.
The smp_processor_id() shouldn't be called from preemptible code.
Instead use get_cpu() and put_cpu() which disables preemption in
addition to getting the processor id. Enable preemption back after
calling schedule_work() to make sure that the work gets scheduled on all
cores other than the current core. We want to avoid a scenario where
current core's stack trace is printed multiple times and one core's
stack trace isn't printed because of scheduling of current task.
This fixes the following bug:
[ 119.143590] sysrq: Show backtrace of all active CPUs
[ 119.143902] BUG: using smp_processor_id() in preemptible [00000000] code: bash/873
[ 119.144586] caller is debug_smp_processor_id+0x20/0x30
[ 119.144827] CPU: 6 PID: 873 Comm: bash Not tainted 5.10.124-dirty #3
[ 119.144861] Hardware name: QEMU QEMU Virtual Machine, BIOS 2023.05-1 07/22/2023
[ 119.145053] Call trace:
[ 119.145093] dump_backtrace+0x0/0x1a0
[ 119.145122] show_stack+0x18/0x70
[ 119.145141] dump_stack+0xc4/0x11c
[ 119.145159] check_preemption_disabled+0x100/0x110
[ 119.145175] debug_smp_processor_id+0x20/0x30
[ 119.145195] sysrq_handle_showallcpus+0x20/0xc0
[ 119.145211] __handle_sysrq+0x8c/0x1a0
[ 119.145227] write_sysrq_trigger+0x94/0x12c
[ 119.145247] proc_reg_write+0xa8/0xe4
[ 119.145266] vfs_write+0xec/0x280
[ 119.145282] ksys_write+0x6c/0x100
[ 119.145298] __arm64_sys_write+0x20/0x30
[ 119.145315] el0_svc_common.constprop.0+0x78/0x1e4
[ 119.145332] do_el0_svc+0x24/0x8c
[ 119.145348] el0_svc+0x10/0x20
[ 119.145364] el0_sync_handler+0x134/0x140
[ 119.145381] el0_sync+0x180/0x1c0
Cc: jirislaby@kernel.org
Cc: stable@vger.kernel.org
Fixes: 47cab6a722d4 ("debug lockups: Improve lockup detection, fix generic arch fallback")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20231009162021.3607632-1-usama.anjum@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d81ffb87aaa75f842cd7aa57091810353755b3e6 ]
Add check for the return value of kstrdup() and return the error, if it
fails in order to avoid NULL pointer dereference.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230904035220.48164-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11e7f27b79757b6586645d87b95d5b78375ecdfc ]
There is a pid leakage:
------------------------------
unreferenced object 0xffff88810c181940 (size 224):
comm "sshd", pid 8191, jiffies 4294946950 (age 524.570s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 ad 4e ad de .............N..
ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:
[<ffffffff814774e6>] kmem_cache_alloc+0x5c6/0x9b0
[<ffffffff81177342>] alloc_pid+0x72/0x570
[<ffffffff81140ac4>] copy_process+0x1374/0x2470
[<ffffffff81141d77>] kernel_clone+0xb7/0x900
[<ffffffff81142645>] __se_sys_clone+0x85/0xb0
[<ffffffff8114269b>] __x64_sys_clone+0x2b/0x30
[<ffffffff83965a72>] do_syscall_64+0x32/0x80
[<ffffffff83a00085>] entry_SYSCALL_64_after_hwframe+0x61/0xc6
It turns out that there is a race condition between disassociate_ctty() and
tty_signal_session_leader(), which caused this leakage.
The pid memleak is triggered by the following race:
task[sshd] task[bash]
----------------------- -----------------------
disassociate_ctty();
spin_lock_irq(¤t->sighand->siglock);
put_pid(current->signal->tty_old_pgrp);
current->signal->tty_old_pgrp = NULL;
tty = tty_kref_get(current->signal->tty);
spin_unlock_irq(¤t->sighand->siglock);
tty_vhangup();
tty_lock(tty);
...
tty_signal_session_leader();
spin_lock_irq(&p->sighand->siglock);
...
if (tty->ctrl.pgrp) //tty->ctrl.pgrp is not NULL
p->signal->tty_old_pgrp = get_pid(tty->ctrl.pgrp); //An extra get
spin_unlock_irq(&p->sighand->siglock);
...
tty_unlock(tty);
if (tty) {
tty_lock(tty);
...
put_pid(tty->ctrl.pgrp);
tty->ctrl.pgrp = NULL; //It's too late
...
tty_unlock(tty);
}
The issue is believed to be introduced by commit c8bcd9c5be24 ("tty:
Fix ->session locking") who moves the unlock of siglock in
disassociate_ctty() above "if (tty)", making a small window allowing
tty_signal_session_leader() to kick in. It can be easily reproduced by
adding a delay before "if (tty)" and at the entrance of
tty_signal_session_leader().
To fix this issue, we move "put_pid(current->signal->tty_old_pgrp)" after
"tty->ctrl.pgrp = NULL".
Fixes: c8bcd9c5be24 ("tty: Fix ->session locking")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Co-developed-by: GUO Zihua <guozihua@huawei.com>
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Link: https://lore.kernel.org/r/20230831023329.165737-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 33092fb3af51deb80849e90a17bada44bbcde6b3 upstream.
The UC-257 is a serial + LPT card, so remove it from this driver.
A patch has been submitted to add it to parport_serial instead.
Additionaly, the UC-431 does not use this card ID, only the UC-420
does. The 431 is a 3-port card and there is no generic 3-port configuration
available, so remove reference to it from this driver.
Fixes: 152d1afa834c ("tty: Add support for Brainboxes UC cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB78995ADF7394C74AD4CF3357C4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
