commit 73f476aa1975bae6a792b340f5b26ffcfba869a6 upstream.
The previous implementation of .handle_interrupt() did not take into
account the fact that all the interrupt status registers should be
acknowledged since multiple interrupt sources could be asserted.
Fix this by reading all the status registers before exiting with
IRQ_NONE or triggering the PHY state machine.
Fixes: 1d1ae3c6ca3f ("net: phy: ti: implement generic .handle_interrupt() callback")
Reported-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210226153020.867852-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71803c1dfa29e0d13b99e48fda11107cc8caebc7 ]
The ndev->dev and pdev->dev aren't the same device, use ndev->dev.parent
which has dma_mask, ndev->dev.parent is just pdev->dev.
Or it would cause the following issue:
[ 39.933526] ------------[ cut here ]------------
[ 39.938414] WARNING: CPU: 1 PID: 501 at kernel/dma/mapping.c:149 dma_map_page_attrs+0x90/0x1f8
Fixes: f959dcd6ddfd ("dma-direct: Fix potential NULL pointer dereference")
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 256748d5480bb3c4b731236c6d6fc86a8e2815d8 ]
DP83848 datasheet (section 4.7.2) indicates that the reset pin should be
toggled after the clocks are running. Add the PHY_RST_AFTER_CLK_EN to
make sure that this indication is respected.
In my experience not having this flag enabled would lead to, on some
boots, the wrong MII mode being selected if the PHY was initialized on
the bootloader and was receiving data during Linux boot.
Signed-off-by: Diogo Silva <diogompaissilva@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 34e45ad9378c ("net: phy: dp83848: Add TI DP83848 Ethernet PHY")
Link: https://patch.msgid.link/20241102151504.811306-1-paissilva@ld-100007.ds1.internal
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d1ae3c6ca3ff49843d73852bb2a8153ce16f432 ]
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 256748d5480b ("net: phy: ti: add PHY_RST_AFTER_CLK_EN flag")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 293e9a3d950dfebc76d9fa6931e6f91ef856b9ab ]
These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 256748d5480b ("net: phy: ti: add PHY_RST_AFTER_CLK_EN flag")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df3dff8ab6d79edc942464999d06fbaedf8cdd18 ]
When the driver is uninstalled and the VF is disabled concurrently, a
kernel crash occurs. The reason is that the two actions call function
pci_disable_sriov(). The num_VFs is checked to determine whether to
release the corresponding resources. During the second calling, num_VFs
is not 0 and the resource release function is called. However, the
corresponding resource has been released during the first invoking.
Therefore, the problem occurs:
[15277.839633][T50670] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
...
[15278.131557][T50670] Call trace:
[15278.134686][T50670] klist_put+0x28/0x12c
[15278.138682][T50670] klist_del+0x14/0x20
[15278.142592][T50670] device_del+0xbc/0x3c0
[15278.146676][T50670] pci_remove_bus_device+0x84/0x120
[15278.151714][T50670] pci_stop_and_remove_bus_device+0x6c/0x80
[15278.157447][T50670] pci_iov_remove_virtfn+0xb4/0x12c
[15278.162485][T50670] sriov_disable+0x50/0x11c
[15278.166829][T50670] pci_disable_sriov+0x24/0x30
[15278.171433][T50670] hnae3_unregister_ae_algo_prepare+0x60/0x90 [hnae3]
[15278.178039][T50670] hclge_exit+0x28/0xd0 [hclge]
[15278.182730][T50670] __se_sys_delete_module.isra.0+0x164/0x230
[15278.188550][T50670] __arm64_sys_delete_module+0x1c/0x30
[15278.193848][T50670] invoke_syscall+0x50/0x11c
[15278.198278][T50670] el0_svc_common.constprop.0+0x158/0x164
[15278.203837][T50670] do_el0_svc+0x34/0xcc
[15278.207834][T50670] el0_svc+0x20/0x30
For details, see the following figure.
rmmod hclge disable VFs
----------------------------------------------------
hclge_exit() sriov_numvfs_store()
... device_lock()
pci_disable_sriov() hns3_pci_sriov_configure()
pci_disable_sriov()
sriov_disable()
sriov_disable() if !num_VFs :
if !num_VFs : return;
return; sriov_del_vfs()
sriov_del_vfs() ...
... klist_put()
klist_put() ...
... num_VFs = 0;
num_VFs = 0; device_unlock();
In this patch, when driver is removing, we get the device_lock()
to protect num_VFs, just like sriov_numvfs_store().
Fixes: 0dd8a25f355b ("net: hns3: disable sriov before unload hclge layer")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241101091507.3644584-1-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d6d26537940f3b3e17138987ed9e4a334780bf7 ]
The c_can_handle_bus_err() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission. The patch fixes the issue by incrementing the
appropriate counter based on the type of error.
Fixes: 881ff67ad450 ("can: c_can: Added support for Bosch C_CAN controller")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241014135319.2009782-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit badccd49b93bb945bf4e5cc8707db67cdc5e27e5 ]
The MAC address of VF can be configured through the mailbox mechanism of
ENETC, but the previous implementation forgot to set the MAC address in
net_device, resulting in the SMAC of the sent frames still being the old
MAC address. Since the MAC address in the hardware has been changed, Rx
cannot receive frames with the DMAC address as the new MAC address. The
most obvious phenomenon is that after changing the MAC address, we can
see that the MAC address of eno0vf0 has not changed through the "ifconfig
eno0vf0" command and the IP address cannot be obtained .
root@ls1028ardb:~# ifconfig eno0vf0 down
root@ls1028ardb:~# ifconfig eno0vf0 hw ether 00:04:9f:3a:4d:56 up
root@ls1028ardb:~# ifconfig eno0vf0
eno0vf0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
ether 66:36:2c:3b:87:76 txqueuelen 1000 (Ethernet)
RX packets 794 bytes 69239 (69.2 KB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 11 bytes 2226 (2.2 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Fixes: beb74ac878c8 ("enetc: Add vf to pf messaging support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20241029090406.841836-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
