FireAsf 🔥
![]() [ Upstream commit f490c492e946d8ffbe65ad4efc66de3c5ede30a4 ] On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit value that represents the frequency of the crystal oscillator connected to the switch IC. The field is populated by the state of the ESW_P4_LED_0 and ESW_P4_LED_0 pins, which is done right after reset is deasserted. ESW_P4_LED_0 ESW_P3_LED_0 Frequency ----------------------------------------- 0 0 Reserved 0 1 20MHz 1 0 40MHz 1 1 25MHz On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0 pin is used to populate the bit. 25MHz when the pin is high, 40MHz when it's low. These pins are also used with LEDs, therefore, their state can be set to something other than the bootstrapping configuration. For example, a link may be established on port 3 before the DSA subdriver takes control of the switch which would set ESW_P3_LED_0 to high. Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is described between reset assertion and deassertion. Some switch ICs in real life conditions cannot always have these pins set back to the bootstrapping configuration before reset deassertion in this amount of delay. This causes wrong crystal frequency to be selected which puts the switch in a nonfunctional state after reset deassertion. The tests below are conducted on an MT7530 with a 40MHz crystal oscillator by Justin Swartz. With a cable from an active peer connected to port 3 before reset, an incorrect crystal frequency (0b11 = 25MHz) is selected: [1] [3] [5] : : : _____________________________ __________________ ESW_P4_LED_0 |_______| _____________________________ ESW_P3_LED_0 |__________________________ : : : : : : [4]...: : : [2]................: [1] Reset is asserted. [2] Period of 1000 - 1100 usec. [3] Reset is deasserted. [4] Period of 315 usec. HWTRAP register is populated with incorrect XTAL frequency. [5] Signals reflect the bootstrapped configuration. Increase the delay between reset_control_assert() and reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount ensures a higher possibility that the switch IC will have these pins back to the bootstrapping configuration before reset deassertion. With a cable from an active peer connected to port 3 before reset, the correct crystal frequency (0b10 = 40MHz) is selected: [1] [2-1] [3] [5] : : : : _____________________________ __________________ ESW_P4_LED_0 |_______| ___________________ _______ ESW_P3_LED_0 |_________| |__________________ : : : : : : [2-2]...: [4]...: [2]................: [1] Reset is asserted. [2] Period of 5000 - 5100 usec. [2-1] ESW_P3_LED_0 goes low. [2-2] Remaining period of 5000 - 5100 usec. [3] Reset is deasserted. [4] Period of 310 usec. HWTRAP register is populated with bootstrapped XTAL frequency. [5] Signals reflect the bootstrapped configuration. ESW_P3_LED_0 low period before reset deassertion: 5000 usec - 5100 usec TEST RESET HOLD # (usec) --------------------- 1 5410 2 5440 3 4375 4 5490 5 5475 6 4335 7 4370 8 5435 9 4205 10 4335 11 3750 12 3170 13 4395 14 4375 15 3515 16 4335 17 4220 18 4175 19 4175 20 4350 Min 3170 Max 5490 Median 4342.500 Avg 4466.500 Revert commit 2920dd92b980 ("net: dsa: mt7530: disable LEDs before reset"). Changing the state of pins via reset assertion is simpler and more efficient than doing so by setting the LED controller off. Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch") Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za> Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> |
||
---|---|---|
.github/workflows | ||
android | ||
arch | ||
block | ||
certs | ||
crypto | ||
Documentation | ||
drivers | ||
firmware/tsp_goodix | ||
fs | ||
gki | ||
include | ||
init | ||
io_uring | ||
ipc | ||
kernel | ||
kernel_build | ||
kunitconfigs | ||
lib | ||
LICENSES | ||
mm | ||
net | ||
samples | ||
scripts | ||
security | ||
sound | ||
test | ||
tools | ||
usr | ||
virt | ||
build.config.aarch64 | ||
build.config.allmodconfig | ||
build.config.allmodconfig.aarch64 | ||
build.config.allmodconfig.arm | ||
build.config.allmodconfig.x86_64 | ||
build.config.amlogic | ||
build.config.arm | ||
build.config.common | ||
build.config.db845c | ||
build.config.erd8825_a25_s | ||
build.config.erd8825_s | ||
build.config.erd9925_evt0_s | ||
build.config.erd9925_evt0_s5300_s | ||
build.config.erd9925_s | ||
build.config.gki | ||
build.config.gki-debug.aarch64 | ||
build.config.gki-debug.x86_64 | ||
build.config.gki.aarch64 | ||
build.config.gki.aarch64.fips140 | ||
build.config.gki.aarch64.fips140_eval_testing | ||
build.config.gki.x86_64 | ||
build.config.gki_kasan | ||
build.config.gki_kasan.aarch64 | ||
build.config.gki_kasan.x86_64 | ||
build.config.gki_kprobes | ||
build.config.gki_kprobes.aarch64 | ||
build.config.gki_kprobes.x86_64 | ||
build.config.hikey960 | ||
build.config.khwasan | ||
build.config.mcd | ||
build.config.rockchip | ||
build.config.universal2100_s | ||
build.config.universal8825_s | ||
build.config.universal9925_evt0_s | ||
build.config.universal9925_s | ||
build.config.x86_64 | ||
build.sh | ||
COPYING | ||
CREDITS | ||
Kbuild | ||
Kconfig | ||
linux-stable.sh | ||
MAINTAINERS | ||
Makefile | ||
OWNERS | ||
README | ||
README.md | ||
vendor_boot_module_order_exynos2100.cfg | ||
vendor_boot_module_order_s5e8825.cfg | ||
vendor_boot_module_order_s5e9925.cfg | ||
vendor_module_list_s5e8825.cfg | ||
vendor_module_list_s5e9925.cfg | ||
vendor_module_list_s5e9925_b0s.cfg | ||
vendor_module_list_s5e9925_g0s.cfg | ||
vendor_module_list_s5e9925_r0s.cfg |
How do I submit patches to Android Common Kernels
-
BEST: Make all of your changes to upstream Linux. If appropriate, backport to the stable releases. These patches will be merged automatically in the corresponding common kernels. If the patch is already in upstream Linux, post a backport of the patch that conforms to the patch requirements below.
- Do not send patches upstream that contain only symbol exports. To be considered for upstream Linux,
additions of
EXPORT_SYMBOL_GPL()
require an in-tree modular driver that uses the symbol -- so include the new driver or changes to an existing driver in the same patchset as the export. - When sending patches upstream, the commit message must contain a clear case for why the patch is needed and beneficial to the community. Enabling out-of-tree drivers or functionality is not not a persuasive case.
- Do not send patches upstream that contain only symbol exports. To be considered for upstream Linux,
additions of
-
LESS GOOD: Develop your patches out-of-tree (from an upstream Linux point-of-view). Unless these are fixing an Android-specific bug, these are very unlikely to be accepted unless they have been coordinated with kernel-team@android.com. If you want to proceed, post a patch that conforms to the patch requirements below.
Common Kernel patch requirements
- All patches must conform to the Linux kernel coding standards and pass
script/checkpatch.pl
- Patches shall not break gki_defconfig or allmodconfig builds for arm, arm64, x86, x86_64 architectures (see https://source.android.com/setup/build/building-kernels)
- If the patch is not merged from an upstream branch, the subject must be tagged with the type of patch:
UPSTREAM:
,BACKPORT:
,FROMGIT:
,FROMLIST:
, orANDROID:
. - All patches must have a
Change-Id:
tag (see https://gerrit-review.googlesource.com/Documentation/user-changeid.html) - If an Android bug has been assigned, there must be a
Bug:
tag. - All patches must have a
Signed-off-by:
tag by the author and the submitter
Additional requirements are listed below based on patch type
Requirements for backports from mainline Linux: UPSTREAM:
, BACKPORT:
- If the patch is a cherry-pick from Linux mainline with no changes at all
- tag the patch subject with
UPSTREAM:
. - add upstream commit information with a
(cherry picked from commit ...)
line - Example:
- if the upstream commit message is
- tag the patch subject with
important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
- then Joe Smith would upload the patch for the common kernel as
UPSTREAM: important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
Bug: 135791357
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
(cherry picked from commit c31e73121f4c1ec41143423ac6ce3ce6dafdcec1)
Signed-off-by: Joe Smith <joe.smith@foo.org>
- If the patch requires any changes from the upstream version, tag the patch with
BACKPORT:
instead ofUPSTREAM:
.- use the same tags as
UPSTREAM:
- add comments about the changes under the
(cherry picked from commit ...)
line - Example:
- use the same tags as
BACKPORT: important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
Bug: 135791357
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
(cherry picked from commit c31e73121f4c1ec41143423ac6ce3ce6dafdcec1)
[joe: Resolved minor conflict in drivers/foo/bar.c ]
Signed-off-by: Joe Smith <joe.smith@foo.org>
Requirements for other backports: FROMGIT:
, FROMLIST:
,
- If the patch has been merged into an upstream maintainer tree, but has not yet
been merged into Linux mainline
- tag the patch subject with
FROMGIT:
- add info on where the patch came from as
(cherry picked from commit <sha1> <repo> <branch>)
. This must be a stable maintainer branch (not rebased, so don't uselinux-next
for example). - if changes were required, use
BACKPORT: FROMGIT:
- Example:
- if the commit message in the maintainer tree is
- tag the patch subject with
important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
- then Joe Smith would upload the patch for the common kernel as
FROMGIT: important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
Bug: 135791357
(cherry picked from commit 878a2fd9de10b03d11d2f622250285c7e63deace
https://git.kernel.org/pub/scm/linux/kernel/git/foo/bar.git test-branch)
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
Signed-off-by: Joe Smith <joe.smith@foo.org>
- If the patch has been submitted to LKML, but not accepted into any maintainer tree
- tag the patch subject with
FROMLIST:
- add a
Link:
tag with a link to the submittal on lore.kernel.org - add a
Bug:
tag with the Android bug (required for patches not accepted into a maintainer tree) - if changes were required, use
BACKPORT: FROMLIST:
- Example:
- tag the patch subject with
FROMLIST: important patch from upstream
This is the detailed description of the important patch
Signed-off-by: Fred Jones <fred.jones@foo.org>
Bug: 135791357
Link: https://lore.kernel.org/lkml/20190619171517.GA17557@someone.com/
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
Signed-off-by: Joe Smith <joe.smith@foo.org>
Requirements for Android-specific patches: ANDROID:
- If the patch is fixing a bug to Android-specific code
- tag the patch subject with
ANDROID:
- add a
Fixes:
tag that cites the patch with the bug - Example:
- tag the patch subject with
ANDROID: fix android-specific bug in foobar.c
This is the detailed description of the important fix
Fixes: 1234abcd2468 ("foobar: add cool feature")
Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
Signed-off-by: Joe Smith <joe.smith@foo.org>
- If the patch is a new feature
- tag the patch subject with
ANDROID:
- add a
Bug:
tag with the Android bug (required for android-specific features)
- tag the patch subject with