/* SPDX-License-Identifier: GPL-2.0 */
/**
*
* Copyright (c) 2021 Samsung Electronics Co., Ltd.
* http://www.samsung.com
*
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 of
* the License as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef _SNPS_USBDP_TCA_REG_H_
#define _SNPS_USBDP_TCA_REG_H_
#define SNPS_USBDPPHY_TCA_TCA_CLK_RST 0x0000
typedef union {
u32 data;
struct {
/* bit[0] Enable for suspend_clk as the tca_clk.
* - 1'b0: PHY ref_clk_sel decides the tca_clk. If ref_clk_sel is 1'b1,
* ref_clk from PHY is the tca_clk, else suspend_clk is the tca_clk.
* - 1'b1: suspend_clk is used as the tca_clk. */
unsigned suspend_clk_en:1;
/* bit[1] tca_ref_clk_en to the DPAlt_X-Bar , enables ref_dig_clk generation
* even though [dp,ss]_ref_clk_en might be low.
* - 1'b0: No request from TCA for ref_clk. ref_clk is is enabled
* based on request from DP or SS+ protocol layer.
* - 1'b1: Request from TCA for ref_clk to be enabled.
* Note :- The final ref_clk_en to PMA is OR of tca_ref_clk_en,
* and dp_ref_clk_en, ss_ref_clk_en */
unsigned tca_ref_clk_en:1;
/* bit[2] Enable automatic or dynamic clock gating of tca_clk when
* TCPC requests are processed for power saving
* - 1'b0: tca_clk is always enabled.
* - 1'b1: tca_clk is dynamically gated when there is no TCPC request
* pending to be completed. tca_clk is enabled when a new TCPC request comes. */
unsigned tca_clk_auto_gate_en:1;
/* bit[7:3] */
unsigned RSVD7_3:5;
/* bit[8] phy_reset SW override.
* - 1'b0: No phy_reset override
* - 1'b1: phy_reset is asserted (override on phy_reset coming from
* ComboPHY top) to UPCS,PMA, and PCS_RAW. A Soft tca_phy_reset can
* be driven by asserting this Bit for the required duration. */
unsigned phy_rst_sw:1;
/* bit[9] XBar_Assist Soft Reset
* - 1'b0: Soft reset is applied. Active low Soft Reset to X-bar Assist,
* pulse low to apply the reset.
* - 1'b1: Soft reset is not applied */
unsigned xa_rst_sw:1;
/* bit[10] VBUS Assist Soft Reset
* - 1'b0: Soft reset is applied. Active low Soft Reset to VBUS Assist,
* pulse low to apply the reset.
* - 1'b1: Soft reset is not applied */
unsigned vba_rst_sw:1;
/* bit[31:11] */
unsigned RSVD31_11:21;
} b;
} SNPS_USBDPPHY_TCA_TCA_CLK_RST_o, *SNPS_USBDPPHY_TCA_TCA_CLK_RST_p;
#define SNPS_USBDPPHY_TCA_TCA_INTR_EN 0x0004
typedef union {
u32 data;
struct {
/* bit[0] XBar_Assist ack event enable
* - 1'b0: Ack event is disabled
* - 1'b1: Ack event is enabled
* When enabled, tca_int interrupt is generated for XBar_Assist TCPC
* request completion requested through write to TCA_TCPC register
* for desired ComboPHY configuration. */
unsigned xa_ack_evt_en:1;
/* bit[1] XBar_Assist timeout event enable
* - 1'b0: Timeout event is disabled
* - 1'b1: Timeout event is enabled
* When enabled, tca_int interrupt is generated on timeout of the TCPC
* request which was requested through write to TCA_TCPC register. */
unsigned xa_timeout_evt_en:1;
/* bit[7:2] */
unsigned RSVD7_2:6;
/* bit[8] sys_vbusvalid change event enable
* - 1'b0: Change event is disabled
* - 1'b1: Change event is enabled
* When enabled, tca_int interrupt is generated when
* sys_vbusvalid input to TCA changes. */
unsigned sys_vbusvalid_evt_en:1;
/* bit[9] */
unsigned RSVD9:1;
/* bit[10] tca_vbusvalid change event enable
* - 1'b0: Change event is disabled
* - 1'b1: Change event is enabled
* When enabled, tca_int interrupt is generated when
* tca_vbusvalid output from TCA changes. */
unsigned tca_vbusvalid_evt_en:1;
/* bit[11] */
unsigned RSVD11:1;
/* bit[12] tca_drv_host_vbus change event enable
* - 1'b0: Change event is disabled
* - 1'b1: Change event is enabled
* When enabled, tca_int interrupt is generated when
* tca_drv_host_vbus output from TCA changes. */
unsigned tca_drv_host_vbus_evt_en:1;
/* bit[15:13] */
unsigned RSVD15_13:3;
/* bit[16] ss_lane1_active change event enable
* - 1'b0: Change event is disabled
* - 1'b1: Change event is enabled
* ss_lane1_active TCA input changes. */
unsigned ss_lane1_active_evt_en:1;
/* bit[31:17] */
unsigned RSVD31_17:15;
} b;
} SNPS_USBDPPHY_TCA_TCA_INTR_EN_o, *SNPS_USBDPPHY_TCA_TCA_INTR_EN_p;
#define SNPS_USBDPPHY_TCA_TCA_INTR_STS 0x0008
typedef union {
u32 data;
struct {
/* bit[0] XBar_Assist ack event status
* - 1'b0: Ack event has not occured (or been cleared when 1'b1 is written)
* - 1'b1: Ack event has occurred with tca_int interrupt asserted,
* indicating XBar_Assist TCPC request completion.
* Note: This bit is set by the hardware and can be cleared by writing 1'b1 on it */
unsigned xa_ack_evt:1;
/* bit[1] XBar_Assist timeout event status
* - 1'b0: Timeout event has not occured (or been cleared when 1'b1 is written)
* - 1'b1: Timeout event has occurred with tca_int interrup asserted,
* indicating timeout of the TCPC request.
* Note: This bit is set by the hardware and can be cleared by writing 1'b1 on it */
unsigned xa_timeout_evt:1;
/* bit[7:2] */
unsigned RSVD7_2:6;
/* bit[8] sys_vbusvalid change event status
* - 1'b0: Change event has not occured (or been cleared when 1'b1 is written)
* - 1'b1: Change event has occurred with tca_int interrupt asserted,
* indicating sys_vbusvalid change.
* Note: This bit is set by the hardware and can be cleared by writing 1'b1 on it */
unsigned sys_vbusvalid_evt:1;
/* bit[9] sys_vbusvalid status/value as seen on TCA input. */
unsigned sys_vbusvalid:1;
/* bit[10] tca_vbusvalid change event status
* - 1'b0: Change event has not occured (or been cleared when 1'b1 is written)
* - 1'b1: Change event has has occurred with tca_int interrupt asserted,
* indicating tca_vbusvalid change.
* Note: This bit is set by the hardware and can be cleared by writing 1'b1 on it */
unsigned tca_vbusvalid_evt:1;
/* bit[11] tca_vbusvalid status/value as seen on TCA output. */
unsigned tca_vbusvalid:1;
/* bit[12] tca_drv_host_vbus change event status
* - 1'b0: Change event has not occured (or been cleared when 1'b1 is written)
* - 1'b1: Change event has has occurred with tca_int interrupt asserted,
* indicating tca_drv_host_vbus change.
* Note: This bit is set by the hardware and can be cleared by writing 1'b1 on it */
unsigned tca_drv_host_vbus_evt:1;
/* bit[13] tca_ drv_host_vbus status/value as seen on TCA output. */
unsigned tca_drv_host_vbus:1;
/* bit[15:14] */
unsigned RSVD15_14:2;
/* bit[16] ss_lane1_active input change event status
* - 1'b0: Change event has not occured (or been cleared when 1'b1 is written)
* - 1'b1: Change event has has occurred with tca_int interrupt asserted,
* indicating ss_lane1_active input change.
* Note: This bit is set by the hardware and can be cleared by writing 1'b1 on it */
unsigned ss_lane1_active_evt:1;
/* bit[17] ss_lane1_active status/value as seen on TCA input. */
unsigned ss_lane1_active:1;
/* bit[31:18] */
unsigned RSVD31_18:14;
} b;
} SNPS_USBDPPHY_TCA_TCA_INTR_STS_o, *SNPS_USBDPPHY_TCA_TCA_INTR_STS_p;
#define SNPS_USBDPPHY_TCA_TCA_GCFG 0x0010
typedef union {
u32 data;
struct {
/* bit[1:0] DPAlt Crossbar Operational Mode
* - 2'bx0: System Configuration Mode, use TCA_SYSMODE_CFG Register for
* DPAlt_Xbar direct control. The SW layers explicitly need to synchronize
* DP and USB controller to have all PHY lanes in P3 for
* flip/conn_mode[1:0]/disable operation.
* - 2'bx1: Controller Synced Mode, use TCA_TCPC Register for DPAlt_Xbar
* control. The default operational mode where the XBar Assist synchronizes
* between DP and USB Controller to achieve desired P3 state
* requirement on all the lanes of the PHY and apply
* the changes as requested through the TCA_TCPC Register. */
unsigned op_mode:2;
/* bit[3:2] */
unsigned RSVD3_2:2;
/* bit[4] USB Host/Device Mode
* - 1'b0: Default mode, USB Subsystem is in DRP/Host mode.
* - 1'b1: Device mode operation, USB Subsystem is in Device mode
* This is needed as for the Device mode of operation, the Xbar_Assist
* relies on VBUS Valid (instead of ss_rxdetect_disable) for the
* flip/conn_mode switch operation.
* The system should set this to 1'b1 when USB Subsystem is in Device mode. */
unsigned role_hstdev:1;
/* bit[7:5] */
unsigned RSVD7_5:3;
/* bit[8] Reset enable for PHY safe state.
* - 1'b0: Disables reset assertion during typec disabled state
* or PHY safestate. (Default value)
* - 1'b1: Enables reset assertion during typec disabled state
* or PHY safestate. */
unsigned physafe_reset_en:1;
/* bit[31:9] */
unsigned RSVD31_9:23;
} b;
} SNPS_USBDPPHY_TCA_TCA_GCFG_o, *SNPS_USBDPPHY_TCA_TCA_GCFG_p;
#define SNPS_USBDPPHY_TCA_TCA_TCPC 0x0014
typedef union {
u32 data;
struct {
/* bit[1:0] Mux control from TCPM controlling the behavior of the
* ComboPHY DPAlt_Xbar and TCA synchronization.
* - 2'b00: No connection (default)
* - 2'b01: USB3.1 Connected
* - 2'b10: DP Alternate Mode - 4 lanes
* - 2'b11: USB3.1 + Display Port Lanes 0 and 1 */
unsigned tcpc_mux_control:2;
/* bit[2] Connector orientation from TCPM
* - 1'b0: Normal (CC1=A5, CC2=B5, TX1=A2/A3, RX1=B10/B11), default
* - 1'b1: Flipped (CC2=A5, CC1=B5, TX1=B2/B3, RX1=A10/A11)
* Note: The selection is swapped when typec_flip_invert input to the ComboPHY is 1'b1. */
unsigned tcpc_connector_orientation:1;
/* bit[3] Control from TCPM to put the PHY in lowpower/Safe state.
* - 1'b0: Standard Operation
* - 1'b1: Disable PHY and use advanced low power strategy (P3.Disable
* on all PHY lanes with even lower power consumtion than P3).
* Also puts all the PHY lanes in USB Safe state. */
unsigned tcpc_low_power_en:1;
/* bit[4] When written as 1'b1, indicates to the XBar_Assist that other 3 fields
* in this register are valid and the operation requested needs to be
* performed by the XBar_Assist. This bit is auto cleared by the
* XBar_Assist, when XBar_Assist has read the required request. */
unsigned tcpc_valid:1;
/* bit[31:5] */
unsigned RSVD31_5:27;
} b;
} SNPS_USBDPPHY_TCA_TCA_TCPC_o, *SNPS_USBDPPHY_TCA_TCA_TCPC_p;
#define SNPS_USBDPPHY_TCA_TCA_SYSMODE_CFG 0x0018
typedef union {
u32 data;
struct {
/* bit[1:0] Drives the typec_conn_mode[1:0] input of the XBAR. Selects the
* DPAlt_XBar config based on the pin configuration requested to
* support the desired DisplayPort Alternate Mode [DPALT].
* - 2'b00: Reserved
* - 2'b01: USB-Only Pin Configuration
* - 2'b10: DPALT Pin configuration C,E
* - 2'b11: DPALT Pin configuration D,F */
unsigned typec_conn_mode:2;
/* bit[2] Drives the typec_flip input of the XBAR. Selects the DPAlt_XBar
* config based on the flip requested [TYPE-C].
* - 1'b0: Normal (CC1=A5, CC2=B5, TX1=A2/A3, RX1=B10/B11), default
* - 1'b1: Flipped (CC2=A5, CC1=B5, TX1=B2/B3, RX1=A10/A11)
* Note: The selection is swapped when typec_flip_invert input to the ComboPHY is 1'b1. */
unsigned typec_flip:1;
/* bit[3] Drives the typec_disable (or typec_disconnect) input of the XBAR.
* This is driven high when all the lanes are in P3 to achieve LowPower
* operation P3.Disable USB Safe state of ComboPHY serial IOs
* - 1'b0: Standard Operation
* - 1'b1: lowpower USB Safe State operation */
unsigned typec_disable:1;
/* bit[4] Drives the typec_physafe input of the XBAR. This is driven high when
* all lanes are in P3 or P2 to achieve USB safe state of
* Type-C PHY serial IOs.
* - 1'b0: Standard Operation
* - 1'b1: USB Safe State operation */
unsigned typec_physafe:1;
/* bit[5] Drives the typec_reset input of the XBAR. This drives all the
* lane resets of the PHY lanes. */
unsigned typec_reset:1;
/* bit[31:6] */
unsigned RSVD31_6:26;
} b;
} SNPS_USBDPPHY_TCA_TCA_SYSMODE_CFG_o, *SNPS_USBDPPHY_TCA_TCA_SYSMODE_CFG_p;
#define SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_CFG0 0x0020
typedef union {
u32 data;
struct {
/* bit[0] When 1'b1, Drives the block_ss_op input to DPAlt_XBar as 1'b1.
* - 1'b0: Normal Mode, SS+ operation is not blocked
* - 1'b1: SS+ operation is immediately blocked to emulate an offchip switch. */
unsigned block_ss_op:1;
/* bit[2:1] When transitioning out of USB modes, selects if SS+ operation
* has to be automatically blocked.
* It helps to emulate behavior similar to external switch by immediately
* killing the USB link and LTSSM reaching RxDetect
* - When bit [0] is 1'b1: Enable automatic assertion of block_ss_op when
* transitioning out of tcpc_mux_control[1:0] USB mode.
* - When bit [1] is 1'b1: Enable automatic assertion of block_ss_op when
* transitioning out of tcpc_mux_control[1:0] USB_DP2 mode. */
unsigned auto_block_ss_op_en:2;
/* bit[3] When transitioning out of USB mode, selects if sstx_detrx_req to PHY
* has to be blocked along with the ss_rxdet_disable request to controller.
* - 1'b0: Does not block sstx_detrx_req to PHY. Relies on controller to
* disable RxDetect when ss_rxdet_disable is asserted.
* - 1'b1: Block sstx_detrx_req to PHY when ss_rxdet_disable to
* controller is asserted. */
unsigned sstx_detrx_req_block_en:1;
/* bit[7:4] */
unsigned RSVD7_4:4;
/* bit[8] Handshake mechanism with USB Controller
* - 1'b0: relies on USB Tx/Rx lanes reaching P3
* - 1'b1: relies on ss_rxdet_disable_ack handshake along with
* USB Tx/Rx lanes reaching P3 */
unsigned ss_hdshk_req:1;
/* bit[9] Handshake mechanism with DP Controller
* - 1'b0: relies on all DP Operational Tx lanes reaching P3
* - 1'b1: relies on dpalt_disable_ack handshake along with all
* DP Operational Tx lanes reaching P3 */
unsigned dp_hdshk_req:1;
/* bit[10] Enable TypeC_MUX switching in P2 state for USB.
* - 1'b0: Switching is allowed only when P3 state is achieved
* - 1'b1: Switching is done when P2 state is achieved. */
unsigned usb_p2_switch_en:1;
/* bit[11] Enable TypeC_MUX switching in P2 state for DP.
* - 1'b0: DP lane switching is allowed only when P3 state is achieved
* - 1'b1: DP lane switching is done when P2 state is achieved. */
unsigned dp_p2_switch_en:1;
/* bit[12] Enable lane ack check bypass during TCA USB lane switching requests
* - 1'b0: TCA checks for tx/rx_ack de-assertion
* - 1'b1: TCA does not check for for tx/rx_ack de-assertion */
unsigned usb_ack_check_bypass_en:1;
/* bit[13] Enable lane ack check bypass during TCA DP lane switching requests
* - 1'b0: TCA checks for tx/rx_ack de-assertion
* - 1'b1: TCA does not check for for tx/rx_ack de-assertion */
unsigned dp_ack_check_bypass_en:1;
/* bit[15:14] */
unsigned RSVD15_14:2;
/* bit[16] Enable automatic transient safe mode (by assertion of typec_disable
* on DPAlt_XBar) when changing DPAlt_XBar configuration (flip/conn_mode[1:0])
* - 1'b0: Transient Safe Mode is not used.
* - 1'b1: Transient Safe Mode is used asserting typec_disable before
* the flip/conn_mode[1:0] change; typec_disable is deasserted
* after the configuration change.
* Note: This bit is only valid when during a TCPC request FLD_LOW_POWER_EN is 1'b0. */
unsigned auto_safe_state:1;
/* bit[31:17] */
unsigned RSVD31_17:15;
} b;
} SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_CFG0_o, *SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_CFG0_p;
#define SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_CFG1 0x0024
typedef union {
u32 data;
struct {
/* bit[19:0] XBar_Assist TCPC Request Timeout value, Timeout value for the TCPC request.
* Calculated as (tca_clk_period*256* FLD_XA_TIMEOUT_VAL).
* The default timeout value is calculated with 19.2MHz tca_clk for value of 500ms */
unsigned xa_timeout_val:20;
/* bit[31:20] */
unsigned RSVD31_20:12;
} b;
} SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_CFG1_o, *SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_CFG1_p;
#define SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_DBG0 0x0028
typedef union {
u32 data;
struct {
/* bit[0] dpalt_dp4 status/value provides the status of the signal
* as driven by TCA block */
unsigned dpalt_dp4:1;
/* bit[1] dpalt_disable status/value provides the status of the signal
* as driven by TCA block */
unsigned dpalt_disable:1;
/* bit[2] dpalt_disable_ack status/value Status/Value as seen on TCA input. */
unsigned dpalt_disable_ack:1;
/* bit[3] */
unsigned RSVD3:1;
/* bit[4] ss_rxdetect_disable status/value provides the status of the signal
* as driven by TCA block. */
unsigned ss_rxdetect_disable:1;
/* bit[5] ss_rxdetect_disable_ack status/value Status/Value as seen on TCA input. */
unsigned ss_rxdetect_disable_ack:1;
/* bit[6] ss_rxdet_disable_1 status/value provides the status of the signal
* as driven by TCA block. */
unsigned ss_rxdet_disable_1:1;
/* bit[7] ss_rxdet_disable_ack_1 status/value Status/Value as seen on TCA input. */
unsigned ss_rxdet_disable_ack_1:1;
/* bit[8] block_ss_op status/value provides the status of the signal
* as driven by TCA block. */
unsigned block_ss_op:1;
/* bit[9] ss_lane0_active status/value as seen on TCA input. */
unsigned ss_lane0_active:1;
/* bit[10] ss_lane1_active status/value as seen on TCA input. */
unsigned ss_lane1_active:1;
/* bit[11] */
unsigned RSVD11:1;
/* bit[12] xbar_ready status/value as driven by XBar_Assist to VBUS_Assist */
unsigned xbar_ready:1;
/* bit[13] tca_clk synchronized status in TCA_PSTATE Register.
* - 1'b0: Status is not synchronized in tca_clk
* - 1'b1: Status is synchronized in tca_clk
* There could be big difference in two values if tca_clk is
* very slow (derived from suspend_clk). */
unsigned pstate_synced:1;
/* bit[14] TCA_PSTATE Register values are captured at which specific moment
* - 1'b0: Current values are shown.
* - 1'b1: Values captured at the moment when TCPC request Timeout occurs. */
unsigned pstate_timeout_val:1;
/* bit[19:15] Multiplier value for xa_req_compl_cycles[15:0] status in
* TCA_CTRLSYNCMODE_DBG1 Register.
* Multiplier = 2 ^ (xa_req_compl_mult[4:0]) */
unsigned xa_req_compl_mult:5;
/* bit[24:20] Override enable bits for
* ctrl_if_ovvrd_en[0]: dpalt_dp4
* ctrl_if_ovvrd_en[1]: dpalt_disable
* ctrl_if_ovvrd_en[2]: dpalt_disable_ack
* ctrl_if_ovvrd_en[3]: ss_rxdet_disable
* ctrl_if_ovvrd_en[4]: ss_rxdet_disable_ack
* Nth bit when 1'b1 enables the override of related controller
* handshake signal using corresponding ctrl_if_ovrrd_val[N]. */
unsigned ctrl_if_ovrrd_en:5;
/* bit[29:25] Override values for controller handshake signals when corresponding
* ctrl_if_ovvrd_en[N] is high. */
unsigned ctrl_if_ovrrd_val:5;
/* bit[31:30] */
unsigned RSVD31_30:2;
} b;
} SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_DBG0_o, *SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_DBG0_p;
#define SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_DBG1 0x002c
typedef union {
u32 data;
struct {
/* bit[15:0] TCPC req completion cycles
* Indicates number of tca_clk clock cycles it took to
* complete the TCPC mode change request using the TCA_TCPC register.
* Calculated as:
* xa_req_comp_cycles * 2 ^ (FLD_XA_REQ_COMP_MULT) */
unsigned xa_req_compl_cycles:16;
/* bit[16] Indicates if the overrun condition has occurred on
* xa_req_comp_cycles[15:0] status register.
* Need to set appropriately high value of FLD_XA_REQ_COMP_MULT. */
unsigned xa_req_compl_cycles_overrun:1;
/* bit[31:17] */
unsigned RSVD31_17:15;
} b;
} SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_DBG1_o, *SNPS_USBDPPHY_TCA_TCA_CTRLSYNCMODE_DBG1_p;
#define SNPS_USBDPPHY_TCA_TCA_PSTATE 0x0030
typedef union {
u32 data;
struct {
/* bit[1:0] ssrx_pstate[1:0] status/value from the PHY */
unsigned ssrx_pstate:2;
/* bit[2] ssrx_req status/value from the PHY */
unsigned ssrx_req:1;
/* bit[3] ssrx_ack status/value from the PHY */
unsigned ssrx_ack:1;
/* bit[5:4] sstx_pstate[1:0] status/value from the PHY */
unsigned sstx_pstate:2;
/* bit[6] sstx_req status/value from the PHY */
unsigned sstx_req:1;
/* bit[7] sstx_ack status/value from the PHY */
unsigned sstx_ack:1;
/* bit[9:8] dp_tx0_pstate[1:0] status/value from the PHY */
unsigned dp_tx0_pstate:2;
/* bit[10] dp_tx0_req status/value from the PHY */
unsigned dp_tx0_req:1;
/* bit[11] dp_tx0_ack status/value from the PHY */
unsigned dp_tx0_ack:1;
/* bit[13:12] dp_tx1_pstate[1:0] status/value from the PHY */
unsigned dp_tx1_pstate:2;
/* bit[14] dp_tx1_req status/value from the PHY */
unsigned dp_tx1_req:1;
/* bit[15] dp_tx1_ack status/value from the PHY */
unsigned dp_tx1_ack:1;
/* bit[17:16] dp_tx2_pstate[1:0] status/value from the PHY */
unsigned dp_tx2_pstate:2;
/* bit[18] dp_tx2_req status/value from the PHY */
unsigned dp_tx2_req:1;
/* bit[19] dp_tx2_ack status/value from the PHY */
unsigned dp_tx2_ack:1;
/* bit[21:20] dp_tx3_pstate[1:0] status/value from the PHY */
unsigned dp_tx3_pstate:2;
/* bit[22] dp_tx3_req status/value from the PHY */
unsigned dp_tx3_req:1;
/* bit[23] dp_tx3_ack status/value from the PHY */
unsigned dp_tx3_ack:1;
/* bit[31:24] */
unsigned RSVD31_24:8;
} b;
} SNPS_USBDPPHY_TCA_TCA_PSTATE_o, *SNPS_USBDPPHY_TCA_TCA_PSTATE_p;
#define SNPS_USBDPPHY_TCA_TCA_GEN_STATUS 0x0034
typedef union {
u32 data;
struct {
/* bit[1:0] phy_typec_conn_mode[1:0] value as driven by TCA to the DPAlt_XBar */
unsigned phy_typec_conn_mode:2;
/* bit[2] phy_typec_flip value as driven by TCA to the DPAlt_XBar */
unsigned phy_typec_flip:1;
/* bit[3] phy_typec_disable value as driven by TCA to the DPAlt_XBar */
unsigned phy_typec_disable:1;
/* bit[4] typec_flip_invert ComboPHY input value as read by the TCA. */
unsigned typec_flip_invert:1;
/* bit[7:5] */
unsigned RSVD7_5:3;
/* bit[8] ref_clk_sel as driven by PMA in the PHY and read by TCA. */
unsigned ref_clk_sel:1;
/* bit[11:9] */
unsigned RSVD11_9:3;
/* bit[12] usb_dev_por ComboPHY input value as read by the TCA. */
unsigned usb_dev_por:1;
/* bit[13] dp4_por ComboPHY input value as read by the TCA. */
unsigned dp4_por:1;
/* bit[31:14] */
unsigned RSVD31_14:18;
} b;
} SNPS_USBDPPHY_TCA_TCA_GEN_STATUS_o, *SNPS_USBDPPHY_TCA_TCA_GEN_STATUS_p;
#define SNPS_USBDPPHY_TCA_TCA_VBUS_CTRL 0x0040
typedef union {
u32 data;
struct {
/* bit[1:0] tca_vbusvalid override
* - 2'b00: drive 0
* - 2'b01: drive 1
* - 2'b10: follow sys_vbusvalid
* - 2'b11: follow sys_vbusvalid with XBar_Assist
* associated override using xbar_ready */
unsigned vbusvalid_overrd:2;
/* bit[3:2] tca_powerpresent override
* - 2'b00: drive 0
* - 2'b01: drive 1
* - 2'b10: follow sys_vbusvalid
* - 2'b11: follow sys_vbusvalid with XBar_Assist
* associated override using xbar_ready */
unsigned powerpresent_overrd:2;
/* bit[5:4] tca_drv_host_vbus overdrive
* - 2'b00: drive 0
* - 2'b01: drive 1
* - 2'b10: drive 0
* - 2'b11: use XBar_Assist sttes to drive tca_drv_host_vbus */
unsigned drv_host_vbus_overrd:2;
/* bit[7:6] */
unsigned RSVD7_6:2;
/* bit[8] tca_iddig control
* - 1'b0: drive 0
* - 1'b1: drive 1 */
unsigned tca_iddig:1;
/* bit[14:9] tca miscellaneous control tca_misc_control[5:0], for each bit
* - 1'b0: drive 0
* - 1'b1: drive 1 */
unsigned tca_misc_ctrl:6;
/* bit[31:15] */
unsigned RSVD31_15:17;
} b;
} SNPS_USBDPPHY_TCA_TCA_VBUS_CTRL_o, *SNPS_USBDPPHY_TCA_TCA_VBUS_CTRL_p;
#define SNPS_USBDPPHY_TCA_TCA_VBUS_STATUS 0x0044
typedef union {
u32 data;
struct {
/* bit[0] sys_vbusvalid status/value as seen on TCA block input. */
unsigned sys_vbusvalid:1;
/* bit[1] tca_vbusvalid status/value as seen on TCA block output. */
unsigned tca_vbusvalid:1;
/* bit[2] tca_powerpresent status/value as seen on TCA block output. */
unsigned tca_powerpresent:1;
/* bit[3] tca_drv_host_vbus status/value as seen on TCA block output. */
unsigned tca_drv_host_vbus:1;
/* bit[31:4] */
unsigned RSVD31_4:28;
} b;
} SNPS_USBDPPHY_TCA_TCA_VBUS_STATUS_o, *SNPS_USBDPPHY_TCA_TCA_VBUS_STATUS_p;
#define SNPS_USBDPPHY_TCA_TCA_INFO_REG 0x00fc
typedef union {
u32 data;
struct {
/* bit[31:0] Version ID for TCA. */
unsigned version_id:32;
} b;
} SNPS_USBDPPHY_TCA_TCA_INFO_REG_o, *SNPS_USBDPPHY_TCA_TCA_INFO_REG_p;
#endif