[ Upstream commit 5311598f7f3293683cdc761df71ae3469327332c ]
After successful PCIe AER recovery, FW will reset all resource
reservations. If it is IF_UP, the driver will call bnxt_open() and
all resources will be reserved again. It it is IF_DOWN, we should
call bnxt_reserve_rings() so that we can reserve resources including
RoCE resources to allow RoCE to resume after AER. Without this
patch, RoCE fails to resume in this IF_DOWN scenario.
Later, if it becomes IF_UP, bnxt_open() will see that resources have
been reserved and will not reserve again.
Fixes: fb1e6e562b37 ("bnxt_en: Fix AER recovery.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c401ed1c709948e57945485088413e1bb5e94bd1 ]
The bcm_sysport_xmit() returns NETDEV_TX_OK without freeing skb
in case of dma_map_single() fails, add dev_kfree_skb() to fix it.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://patch.msgid.link/20241014145115.44977-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 134061163ee5ca4759de5c24ca3bd71608891ba7 upstream.
Fix UBSAN warnings that occur when using a system with 32 physical
cpu cores or more, or when the user defines a number of Ethernet
queues greater than or equal to FP_SB_MAX_E1x using the num_queues
module parameter.
Currently there is a read/write out of bounds that occurs on the array
"struct stats_query_entry query" present inside the "bnx2x_fw_stats_req"
struct in "drivers/net/ethernet/broadcom/bnx2x/bnx2x.h".
Looking at the definition of the "struct stats_query_entry query" array:
struct stats_query_entry query[FP_SB_MAX_E1x+
BNX2X_FIRST_QUEUE_QUERY_IDX];
FP_SB_MAX_E1x is defined as the maximum number of fast path interrupts and
has a value of 16, while BNX2X_FIRST_QUEUE_QUERY_IDX has a value of 3
meaning the array has a total size of 19.
Since accesses to "struct stats_query_entry query" are offset-ted by
BNX2X_FIRST_QUEUE_QUERY_IDX, that means that the total number of Ethernet
queues should not exceed FP_SB_MAX_E1x (16). However one of these queues
is reserved for FCOE and thus the number of Ethernet queues should be set
to [FP_SB_MAX_E1x -1] (15) if FCOE is enabled or [FP_SB_MAX_E1x] (16) if
it is not.
This is also described in a comment in the source code in
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h just above the Macro definition
of FP_SB_MAX_E1x. Below is the part of this explanation that it important
for this patch
/*
* The total number of L2 queues, MSIX vectors and HW contexts (CIDs) is
* control by the number of fast-path status blocks supported by the
* device (HW/FW). Each fast-path status block (FP-SB) aka non-default
* status block represents an independent interrupts context that can
* serve a regular L2 networking queue. However special L2 queues such
* as the FCoE queue do not require a FP-SB and other components like
* the CNIC may consume FP-SB reducing the number of possible L2 queues
*
* If the maximum number of FP-SB available is X then:
* a. If CNIC is supported it consumes 1 FP-SB thus the max number of
* regular L2 queues is Y=X-1
* b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor)
* c. If the FCoE L2 queue is supported the actual number of L2 queues
* is Y+1
* d. The number of irqs (MSIX vectors) is either Y+1 (one extra for
* slow-path interrupts) or Y+2 if CNIC is supported (one additional
* FP interrupt context for the CNIC).
* e. The number of HW context (CID count) is always X or X+1 if FCoE
* L2 queue is supported. The cid for the FCoE L2 queue is always X.
*/
However this driver also supports NICs that use the E2 controller which can
handle more queues due to having more FP-SB represented by FP_SB_MAX_E2.
Looking at the commits when the E2 support was added, it was originally
using the E1x parameters: commit f2e0899f0f27 ("bnx2x: Add 57712 support").
Back then FP_SB_MAX_E2 was set to 16 the same as E1x. However the driver
was later updated to take full advantage of the E2 instead of having it be
limited to the capabilities of the E1x. But as far as we can tell, the
array "stats_query_entry query" was still limited to using the FP-SB
available to the E1x cards as part of an oversignt when the driver was
updated to take full advantage of the E2, and now with the driver being
aware of the greater queue size supported by E2 NICs, it causes the UBSAN
warnings seen in the stack traces below.
This patch increases the size of the "stats_query_entry query" array by
replacing FP_SB_MAX_E1x with FP_SB_MAX_E2 to be large enough to handle
both types of NICs.
Stack traces:
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1529:11
index 20 is out of range for type 'stats_query_entry [19]'
CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_prep_fw_stats_req+0x2e1/0x310 [bnx2x]
bnx2x_stats_init+0x156/0x320 [bnx2x]
bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x]
bnx2x_nic_load+0x8e8/0x19e0 [bnx2x]
bnx2x_open+0x16b/0x290 [bnx2x]
__dev_open+0x10e/0x1d0
RIP: 0033:0x736223927a0a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca
64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a
RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003
RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080
R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0
R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00
</TASK>
---[ end trace ]---
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1546:11
index 28 is out of range for type 'stats_query_entry [19]'
CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_prep_fw_stats_req+0x2fd/0x310 [bnx2x]
bnx2x_stats_init+0x156/0x320 [bnx2x]
bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x]
bnx2x_nic_load+0x8e8/0x19e0 [bnx2x]
bnx2x_open+0x16b/0x290 [bnx2x]
__dev_open+0x10e/0x1d0
RIP: 0033:0x736223927a0a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca
64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a
RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003
RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080
R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0
R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00
</TASK>
---[ end trace ]---
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1895:8
index 29 is out of range for type 'stats_query_entry [19]'
CPU: 13 PID: 163 Comm: kworker/u96:1 Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Workqueue: bnx2x bnx2x_sp_task [bnx2x]
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_iov_adjust_stats_req+0x3c4/0x3d0 [bnx2x]
bnx2x_storm_stats_post.part.0+0x4a/0x330 [bnx2x]
? bnx2x_hw_stats_post+0x231/0x250 [bnx2x]
bnx2x_stats_start+0x44/0x70 [bnx2x]
bnx2x_stats_handle+0x149/0x350 [bnx2x]
bnx2x_attn_int_asserted+0x998/0x9b0 [bnx2x]
bnx2x_sp_task+0x491/0x5c0 [bnx2x]
process_one_work+0x18d/0x3f0
</TASK>
---[ end trace ]---
Fixes: 50f0a562f8cc ("bnx2x: add fcoe statistics")
Signed-off-by: Ghadi Elie Rahme <ghadi.rahme@canonical.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20240627111405.1037812-1-ghadi.rahme@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d5e2a82232605b337972fb2c7d0cbc46898aca1 upstream.
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d85cf67a339685beae1d0aee27b7f61da95455be upstream.
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dbe5f19368caae63b1f59f5bc2af78c7d522b3a upstream.
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f96347628e ("net: bcmgenet: set Rx mode before starting netif")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a6380cb4c6b5c1d6dad226ba3130f9090f0ccea ]
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
See: https://github.com/raspberrypi/firmware/issues/1882
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Maarten Vanraes <maarten@rmail.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e3eb7dd47bd4806f00e104eb6da092c435f9fb21 upstream.
b44_free_rings() accesses b44::rx_buffers (and ::tx_buffers)
unconditionally, but b44::rx_buffers is only valid when the
device is up (they get allocated in b44_open(), and deallocated
again in b44_close()), any other time these are just a NULL pointers.
So if you try to change the pause params while the network interface
is disabled/administratively down, everything explodes (which likely
netifd tries to do).
Link: https://github.com/openwrt/openwrt/issues/13789
Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2)
Cc: stable@vger.kernel.org
Reported-by: Peter Münster <pm@a16n.net>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Tested-by: Peter Münster <pm@a16n.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Peter Münster <pm@a16n.net>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/87y192oolj.fsf@a16n.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d27e2da94a42655861ca4baea30c8cd65546f25d ]
Fix race condition leading to system crash during EEH error handling
During EEH error recovery, the bnx2x driver's transmit timeout logic
could cause a race condition when handling reset tasks. The
bnx2x_tx_timeout() schedules reset tasks via bnx2x_sp_rtnl_task(),
which ultimately leads to bnx2x_nic_unload(). In bnx2x_nic_unload()
SGEs are freed using bnx2x_free_rx_sge_range(). However, this could
overlap with the EEH driver's attempt to reset the device using
bnx2x_io_slot_reset(), which also tries to free SGEs. This race
condition can result in system crashes due to accessing freed memory
locations in bnx2x_free_rx_sge()
799 static inline void bnx2x_free_rx_sge(struct bnx2x *bp,
800 struct bnx2x_fastpath *fp, u16 index)
801 {
802 struct sw_rx_page *sw_buf = &fp->rx_page_ring[index];
803 struct page *page = sw_buf->page;
....
where sw_buf was set to NULL after the call to dma_unmap_page()
by the preceding thread.
EEH: Beginning: 'slot_reset'
PCI 0011:01:00.0#10000: EEH: Invoking bnx2x->slot_reset()
bnx2x: [bnx2x_io_slot_reset:14228(eth1)]IO slot reset initializing...
bnx2x 0011:01:00.0: enabling device (0140 -> 0142)
bnx2x: [bnx2x_io_slot_reset:14244(eth1)]IO slot reset --> driver unload
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0080000025065fc
Oops: Kernel access of bad area, sig: 11 [#1]
.....
Call Trace:
[c000000003c67a20] [c00800000250658c] bnx2x_io_slot_reset+0x204/0x610 [bnx2x] (unreliable)
[c000000003c67af0] [c0000000000518a8] eeh_report_reset+0xb8/0xf0
[c000000003c67b60] [c000000000052130] eeh_pe_report+0x180/0x550
[c000000003c67c70] [c00000000005318c] eeh_handle_normal_event+0x84c/0xa60
[c000000003c67d50] [c000000000053a84] eeh_event_handler+0xf4/0x170
[c000000003c67da0] [c000000000194c58] kthread+0x1c8/0x1d0
[c000000003c67e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
To solve this issue, we need to verify page pool allocations before
freeing.
Fixes: 4cace675d687 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240315205535.1321-1-thinhtr@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a9f31047baca57d47440c879cf259b86f900260c upstream.
We had a number of short comings:
- EEE must be re-evaluated whenever the state machine detects a link
change as wight be switching from a link partner with EEE
enabled/disabled
- tx_lpi_enabled controls whether EEE should be enabled/disabled for the
transmit path, which applies to the TBUF block
- We do not need to forcibly enable EEE upon system resume, as the PHY
state machine will trigger a link event that will do that, too
Fixes: 6ef398ea60d9 ("net: bcmgenet: add EEE support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230606214348.2408018-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c1069fa42872f95cf3c6fedf80723d391e12d57 ]
The first message to firmware may fail if the device is undergoing FLR.
The driver has some recovery logic for this failure scenario but we must
wait 100 msec for FLR to complete before proceeding. Otherwise the
recovery will always fail.
Fixes: ba02629ff6cb ("bnxt_en: log firmware status on firmware init failure")
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240117234515.226944-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e009b2efb7a8850498796b360043ac25c8d3d28f ]
The 2 lines to check for the BNXT_HWRM_PF_UNLOAD_SP_EVENT bit was
mis-applied to bnxt_cfg_ntp_filters() and should have been applied to
bnxt_sp_task().
Fixes: 19241368443f ("bnxt_en: Send PF driver unload notification to all VFs.")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e584f2ff1e6cc9b1d99e8a6b0f3415940d1b3eb3 ]
The flag DMA_TX_APPEND_CRC was only written to the first DMA descriptor
in the TX path, where each descriptor corresponds to a single skbuff
fragment (or the skbuff head). This led to packets with no FCS appearing
on the wire if the kernel allocated the packet in fragments, which would
always happen when using PACKET_MMAP/TPACKET (cf. tpacket_fill_skb() in
net/af_packet.c).
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Adrian Cinal <adriancinal1@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231228135638.1339245-1-adriancinal1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f5020acb33f926030f62563c86dffca35c7b701 ]
Similar to skb_eth_hdr() introduced in commit 96cc4b69581d ("macvlan: do
not assume mac_header is set in macvlan_broadcast()"), let's introduce a
skb_vlan_eth_hdr() helper which can be used in TX-only code paths to get
to the VLAN header based on skb->data rather than based on the
skb_mac_header(skb).
We also consolidate the drivers that dereference skb->data to go through
this helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 9fc95fe95c3e ("net: fec: correct queue selection")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d007caaaf052f82ca2340d4c7b32d04a3f5dbf3f ]
When flow_indr_dev_register() fails, bnxt_init_tc will free
bp->tc_info through kfree(). However, the caller function
bnxt_init_one() will ignore this failure and call
bnxt_shutdown_tc() on failure of bnxt_dl_register(), where
a use-after-free happens. Fix this issue by setting
bp->tc_info to NULL after kfree().
Fixes: 627c89d00fb9 ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://lore.kernel.org/r/20231204024004.8245-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
