[ Upstream commit 680a8217dc00dc7e7da57888b3c053289b60eb2b ]
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42fb3acf6826c6764ba79feb6e15229b43fd2f9f ]
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9234a2549cb6ac038bec36cc7c084218e9575513 ]
If phy_read_mmd() fails, the error code stored in 'bmsr' should be returned
instead of 'val' which is likely to be 0.
Fixes: 75f4d8d10e01 ("net: phy: add Broadcom BCM84881 PHY driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/3e1755b0c40340d00e089d6adae5bca2f8c79e53.1727982168.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a842e443ca8184f2dc82ab307b43a8b38defd6a5 ]
When configuring the fiber port, the DP83869 PHY driver incorrectly
calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit
number (10). This corrupts some other memory location -- in case of
arm64 the priv pointer in the same structure.
Since the advertising flags are updated from supported at the end of the
function the incorrect line isn't needed at all and can be removed.
Fixes: a29de52ba2a1 ("net: dp83869: Add ability to advertise Fiber connection")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241002161807.440378-1-inguin@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eae2c136cb624e4050092feb59f18159b4f2512 ]
There is a bug currently when there are more than one VLAN defined
and any reset that affects the PF is initiated, after the reset rebuild
no traffic will pass on any VLAN but the last one created.
This is caused by the iteration though the VLANs during replay each
clearing the vsi_map bitmap of the VSI that is being replayed. The
problem is that during rhe replay, the pointer to the vsi_map bitmap
is used by each successive vlan to determine if it should be replayed
on this VSI.
The logic was that the replay of the VLAN would replace the bit in the map
before the next VLAN would iterate through. But, since the replay copies
the old bitmap pointer to filt_replay_rules and creates a new one for the
recreated VLANS, it does not do this, and leaves the old bitmap broken
to be used to replay the remaining VLANs.
Since the old bitmap will be cleaned up in post replay cleanup, there is
no need to alter it and break following VLAN replay, so don't clear the
bit.
Fixes: 334cb0626de1 ("ice: Implement VSI replay framework")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac631873c9e7a50d2a8de457cfc4b9f86666403e ]
The recent change to allow large frames without hardware checksumming
slotted in software checksumming in the driver if hardware could not
do it.
This will however upset TSO (TCP Segment Offloading). Typical
error dumps includes this:
skb len=2961 headroom=222 headlen=66 tailroom=0
(...)
WARNING: CPU: 0 PID: 956 at net/core/dev.c:3259 skb_warn_bad_offload+0x7c/0x108
gemini-ethernet-port: caps=(0x0000010000154813, 0x00002007ffdd7889)
And the packets do not go through.
The TSO implementation is bogus: a TSO enabled driver must propagate
the skb_shinfo(skb)->gso_size value to the TSO engine on the NIC.
Drop the size check and TSO offloading features for now: this
needs to be fixed up properly.
After this ethernet works fine on Gemini devices with a direct connected
PHY such as D-Link DNS-313.
Also tested to still be working with a DSA switch using the Gemini
ethernet as conduit interface.
Link: https://lore.kernel.org/netdev/CANn89iJLfxng1sYL5Zk0mknXpyYQPCp83m3KgD2KJ2_hKCpEUg@mail.gmail.com/
Suggested-by: Eric Dumazet <edumazet@google.com>
Fixes: d4d0c5b4d279 ("net: ethernet: cortina: Handle large frames")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ced8e8b8f40accfcce4a2bbd8b150aa76d5eff9a ]
RTL8125 added fields to the tally counter, what may result in the chip
dma'ing these new fields to unallocated memory. Therefore make sure
that the allocated memory area is big enough to hold all of the
tally counter values, even if we use only parts of it.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/741d26a9-2b2b-485d-91d9-ecb302e345b5@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8df9439389a44fb2cc4ef695e08d6a8870b1616c ]
There is a spelling mistake in the struct field tx_underun, rename
it to tx_underrun.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20240909140021.64884-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: ced8e8b8f40a ("r8169: add tally counter fields added with RTL8125")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 675faf5a14c14a2be0b870db30a70764df81e2df upstream.
The commit b8c43360f6e4 ("net: stmmac: No need to calculate speed divider
when offload is disabled") allows the "port_transmit_rate_kbps" to be
set to a value of 0, which is then passed to the "div_s64" function when
tc-cbs is disabled. This leads to a zero-division error.
When tc-cbs is disabled, the idleslope, sendslope, and credit values the
credit values are not required to be configured. Therefore, adding a return
statement after setting the txQ mode to DCB when tc-cbs is disabled would
prevent a zero-division error.
Fixes: b8c43360f6e4 ("net: stmmac: No need to calculate speed divider when offload is disabled")
Cc: <stable@vger.kernel.org>
Co-developed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: KhaiWenTan <khai.wen.tan@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240918061422.1589662-1-khai.wen.tan@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit daaba19d357f0900b303a530ced96c78086267ea ]
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240911094445.1922476-4-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 498365e52bebcbc36a93279fe7e9d6aec8479cee ]
Replace one-element array with a flexible-array member in
`struct host_cmd_ds_802_11_scan_ext`.
With this, fix the following warning:
elo 16 17:51:58 surfacebook kernel: ------------[ cut here ]------------
elo 16 17:51:58 surfacebook kernel: memcpy: detected field-spanning write (size 243) of single field "ext_scan->tlv_buffer" at drivers/net/wireless/marvell/mwifiex/scan.c:2239 (size 1)
elo 16 17:51:58 surfacebook kernel: WARNING: CPU: 0 PID: 498 at drivers/net/wireless/marvell/mwifiex/scan.c:2239 mwifiex_cmd_802_11_scan_ext+0x83/0x90 [mwifiex]
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Closes: https://lore.kernel.org/linux-hardening/ZsZNgfnEwOcPdCly@black.fi.intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/ZsZa5xRcsLq9D+RX@elsanto
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5874e0c9f25661c2faefe4809907166defae3d7f ]
W=1 builds with GCC 14.2.0 warn that:
.../aq_ethtool.c:278:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 6 [-Wformat-truncation=]
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~
.../aq_ethtool.c:278:56: note: directive argument in the range [-2147483641, 254]
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~~~~~~
.../aq_ethtool.c:278:33: note: ‘snprintf’ output between 5 and 15 bytes into a destination of size 8
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
tc is always in the range 0 - cfg->tcs. And as cfg->tcs is a u8,
the range is 0 - 255. Further, on inspecting the code, it seems
that cfg->tcs will never be more than AQ_CFG_TCS_MAX (8), so
the range is actually 0 - 8.
So, it seems that the condition that GCC flags will not occur.
But, nonetheless, it would be nice if it didn't emit the warning.
It seems that this can be achieved by changing the format specifier
from %d to %u, in which case I believe GCC recognises an upper bound
on the range of tc of 0 - 255. After some experimentation I think
this is due to the combination of the use of %u and the type of
cfg->tcs (u8).
Empirically, updating the type of the tc variable to unsigned int
has the same effect.
As both of these changes seem to make sense in relation to what the code
is actually doing - iterating over unsigned values - do both.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821-atlantic-str-v1-1-fa2cfe38ca00@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91d516d4de48532d967a77967834e00c8c53dfe6 ]
Increase size of queue_name buffer from 30 to 31 to accommodate
the largest string written to it. This avoids truncation in
the possibly unlikely case where the string is name is the
maximum size.
Flagged by gcc-14:
.../mvpp2_main.c: In function 'mvpp2_probe':
.../mvpp2_main.c:7636:32: warning: 'snprintf' output may be truncated before the last format character [-Wformat-truncation=]
7636 | "stats-wq-%s%s", netdev_name(priv->port_list[0]->dev),
| ^
.../mvpp2_main.c:7635:9: note: 'snprintf' output between 10 and 31 bytes into a destination of size 30
7635 | snprintf(priv->queue_name, sizeof(priv->queue_name),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
7636 | "stats-wq-%s%s", netdev_name(priv->port_list[0]->dev),
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
7637 | priv->port_count > 1 ? "+" : "");
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Introduced by commit 118d6298f6f0 ("net: mvpp2: add ethtool GOP statistics").
I am not flagging this as a bug as I am not aware that it is one.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Marcin Wojtas <marcin.s.wojtas@gmail.com>
Link: https://patch.msgid.link/20240806-mvpp2-namelen-v1-1-6dc773653f2f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69f253e46af98af17e3efa3e5dfa72fcb7d1983d ]
Currently, the ath11k_soc_dp_stats::hal_reo_error array is defined with a
maximum size of DP_REO_DST_RING_MAX. However, the ath11k_dp_process_rx()
function access ath11k_soc_dp_stats::hal_reo_error using the REO
destination SRNG ring ID, which is incorrect. SRNG ring ID differ from
normal ring ID, and this usage leads to out-of-bounds array access. To fix
this issue, modify ath11k_dp_process_rx() to use the normal ring ID
directly instead of the SRNG ring ID to avoid out-of-bounds array access.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240704070811.4186543-3-quic_periyasa@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e62beddc45f487b9969821fad3a0913d9bc18a2f ]
Driver is leaking OF node reference from
of_parse_phandle_with_fixed_args() in probe().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240827144421.52852-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5680cf8d34e1552df987e2f4bb1bff0b2a8c8b11 ]
Driver is leaking OF node reference from
of_parse_phandle_with_fixed_args() in hns_mac_get_info().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240827144421.52852-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17555297dbd5bccc93a01516117547e26a61caf1 ]
Driver is leaking OF node reference from
of_parse_phandle_with_fixed_args() in probe().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240827144421.52852-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa5e94a1811d68fbffa0725efe6d4ca62c03d12 ]
During the list_for_each_entry_rcu iteration call of xenvif_flush_hash,
kfree_rcu does not exist inside the rcu read critical section, so if
kfree_rcu is called when the rcu grace period ends during the iteration,
UAF occurs when accessing head->next after the entry becomes free.
Therefore, to solve this, you need to change it to list_for_each_entry_safe.
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Link: https://patch.msgid.link/20240822181109.2577354-1-aha310510@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62fdaf9e8056e9a9e6fe63aa9c816ec2122d60c6 ]
In ice_sched_add_root_node() and ice_sched_add_node() there are calls to
devm_kcalloc() in order to allocate memory for array of pointers to
'ice_sched_node' structure. But incorrect types are used as sizeof()
arguments in these calls (structures instead of pointers) which leads to
over allocation of memory.
Adjust over allocation of memory by correcting types in devm_kcalloc()
sizeof() arguments.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94745807f3ebd379f23865e6dab196f220664179 ]
Syzbot points out that skb_trim() has a sanity check on the existing length of
the skb, which can be uninitialised in some error paths. The intent here is
clearly just to reset the length to zero before resubmitting, so switch to
calling __skb_set_length(skb, 0) directly. In addition, __skb_set_length()
already contains a call to skb_reset_tail_pointer(), so remove the redundant
call.
The syzbot report came from ath9k_hif_usb_reg_in_cb(), but there's a similar
usage of skb_trim() in ath9k_hif_usb_rx_cb(), change both while we're at it.
Reported-by: syzbot+98afa303be379af6cdb2@syzkaller.appspotmail.com
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240812142447.12328-1-toke@toke.dk
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f66f26703093886db81f0610b97a6794511917c ]
In 'ath9k_get_et_stats()', promote TX stats counters to 'u64'
to avoid possible integer overflow. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Kandybka <d.kandybka@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240725111743.14422-1-d.kandybka@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45c0de18ff2dc9af01236380404bbd6a46502c69 ]
When applying padding, the buffer is not zeroed, which results in memory
disclosure. The mentioned data is observed on the wire. This patch uses
skb_put_padto() to pad Ethernet frames properly. The mentioned function
zeroes the expanded buffer.
In case the packet cannot be padded it is silently dropped. Statistics
are also not incremented. This driver does not support statistics in the
old 32-bit format or the new 64-bit format. These will be added in the
future. In its current form, the patch should be easily backported to
stable versions.
Ethernet MACs on Amazon-SE and Danube cannot do padding of the packets
in hardware, so software padding must be applied.
Fixes: 504d4721ee8e ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240923214949.231511-2-olek2@wp.pl
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09573b1cc76e7ff8f056ab29ea1cdc152ec8c653 ]
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 8c6ad9cc5157 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/20240911094234.1922418-1-ruanjinjie@huawei.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec793155894140df7421d25903de2e6bc12c695b ]
Collecting crdump involves reading vsc registers from pci config space
of mlx device, which can take long time to complete. This might result
in starving other threads waiting to run on the cpu.
Numbers I got from testing ConnectX-5 Ex MCX516A-CDAT in the lab:
- mlx5_vsc_gw_read_block_fast() was called with length = 1310716.
- mlx5_vsc_gw_read_fast() reads 4 bytes at a time. It was not used to
read the entire 1310716 bytes. It was called 53813 times because
there are jumps in read_addr.
- On average mlx5_vsc_gw_read_fast() took 35284.4ns.
- In total mlx5_vsc_wait_on_flag() called vsc_read() 54707 times.
The average time for each call was 17548.3ns. In some instances
vsc_read() was called more than one time when the flag was not set.
As expected the thread released the cpu after 16 iterations in
mlx5_vsc_wait_on_flag().
- Total time to read crdump was 35284.4ns * 53813 ~= 1.898s.
It was seen in the field that crdump can take more than 5 seconds to
complete. During that time mlx5_vsc_wait_on_flag() did not release the
cpu because it did not complete 16 iterations. It is believed that pci
config reads were slow. Adding cond_resched() every 128 register read
improves the situation. In the common case the, crdump takes ~1.8989s,
the thread yields the cpu every ~4.51ms. If crdump takes ~5s, the thread
yields the cpu every ~18.0ms.
Fixes: 8b9d8baae1de ("net/mlx5: Add Crdump support")
Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bcae12c795f32ddfbf8c80d1b5f1d3286341c32 ]
Remove the erroneous unmap in case no DMA mapping was established
The multi-packet WQE transmit code attempts to obtain a DMA mapping for
the skb. This could fail, e.g. under memory pressure, when the IOMMU
driver just can't allocate more memory for page tables. While the code
tries to handle this in the path below the err_unmap label it erroneously
unmaps one entry from the sq's FIFO list of active mappings. Since the
current map attempt failed this unmap is removing some random DMA mapping
that might still be required. If the PCI function now presents that IOVA,
the IOMMU may assumes a rogue DMA access and e.g. on s390 puts the PCI
function in error state.
The erroneous behavior was seen in a stress-test environment that created
memory pressure.
Fixes: 5af75c747e2a ("net/mlx5e: Enhanced TX MPWQE for SKBs")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Acked-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit addf89774e48c992316449ffab4f29c2309ebefb ]
If REGMAP_SPI is m and IEEE802154_MCR20A is y,
mcr20a.c:(.text+0x3ed6c5b): undefined reference to `__devm_regmap_init_spi'
ld: mcr20a.c:(.text+0x3ed6cb5): undefined reference to `__devm_regmap_init_spi'
Select REGMAP_SPI for IEEE802154_MCR20A to fix it.
Fixes: 8c6ad9cc5157 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/20240909131740.1296608-1-ruanjinjie@huawei.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a71ed5898dfae68262f79277915d1dfe34586bc6 upstream.
"iw dev wlp2s0 station dump" shows incorrect rx bitrate:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 86.7 MBit/s VHT-MCS 9 VHT-NSS 1
This is because the RX band width is calculated incorrectly. Fix the
calculation according to the phydm_rxsc_2_bw() function from the
official drivers.
After:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 390.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 1
It also works correctly with the AP configured for 20 MHz and 40 MHz.
Tested with RTL8822CE.
Cc: stable@vger.kernel.org
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/bca8949b-e2bd-4515-98fd-70d3049a0097@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5109b60ee4fcb2f2bb24f589575e10cc5283ad4 ]
In the ether3_probe function, a timer is initialized with a callback
function ether3_ledoff, bound to &prev(dev)->timer. Once the timer is
started, there is a risk of a race condition if the module or device
is removed, triggering the ether3_remove function to perform cleanup.
The sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| ether3_ledoff
ether3_remove |
free_netdev(dev); |
put_devic |
kfree(dev); |
| ether3_outw(priv(dev)->regs.config2 |= CFG2_CTRLO, REG_CONFIG2);
| // use dev
Fix it by ensuring that the timer is canceled before proceeding with
the cleanup in ether3_remove.
Fixes: 6fd9c53f7186 ("net: seeq: Convert timers to use timer_setup()")
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Link: https://patch.msgid.link/20240915144045.451-1-kxwang23@m.fudan.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9c7ac4fe22c608acf6153a3329df2b6b6cd416c ]
En-Wei reported that traffic breaks if cable is unplugged for more
than 3s and then re-plugged. This was supposed to be fixed by
621735f59064 ("r8169: fix rare issue with broken rx after link-down on
RTL8125"). But apparently this didn't fix the issue for everybody.
The 3s threshold rang a bell, as this is the delay after which ALDPS
kicks in. And indeed disabling ALDPS fixes the issue for this user.
Maybe this fixes the issue in general. In a follow-up step we could
remove the first fix attempt and see whether anybody complains.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Tested-by: En-Wei WU <en-wei.wu@canonical.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/778b9d86-05c4-4856-be59-cde4487b9e52@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 799a9225997799f7b1b579bc50a93b78b4fb2a01 ]
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: bbb96dc7fa1a ("enetc: Factor out the traffic start/stop procedures")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240911094445.1922476-3-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c471236b2359e6b27388475dd04fff0a5e2bf922 ]
Both bareudp_xmit_skb() and bareudp6_xmit_skb() read their skb's inner
IP header to get its ECN value (with ip_tunnel_ecn_encap()). Therefore
we need to ensure that the inner IP header is part of the skb's linear
data.
Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/267328222f0a11519c6de04c640a4f87a38ea9ed.1726046181.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ae073f5903f6c6439d0ac855836a4da5c0a701 ]
When innerprotoinherit is set, the tunneled packets do not have an inner
Ethernet header.
Change 'maclen' to not always assume the header length is ETH_HLEN, as
there might not be a MAC header.
This resolves issues with drivers (e.g. mlx5, in
mlx5e_tx_tunnel_accel()) who rely on the skb inner network header offset
to be correct, and use it for TX offloads.
Fixes: d8a6213d70ac ("geneve: fix header validation in geneve[6]_xmit_skb")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: c471236b2359 ("bareudp: Pull inner IP header on xmit.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 435fe1c0c1f74b682dba85641406abf4337aade6 ]
This patch adds support for encapsulating IPv4/IPv6 within GENEVE.
In order to use this, a new IFLA_GENEVE_INNER_PROTO_INHERIT flag needs
to be provided at device creation. This property cannot be changed for
the time being.
In case IP traffic is received on a non-tun device the drop count is
increased.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220316061557.431872-1-eyal.birger@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: c471236b2359 ("bareudp: Pull inner IP header on xmit.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fa29c85117170b0508790f878b13ec6593c888 ]
Bareudp reads the inner IP header to get the ECN value. Therefore, it
needs to ensure that it's part of the skb's linear data.
This is similar to the vxlan and geneve fixes for that same problem:
* commit f7789419137b ("vxlan: Pull inner IP header in vxlan_rcv().")
* commit 1ca1ba465e55 ("geneve: make sure to pull inner header in
geneve_rx()")
Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/5205940067c40218a70fbb888080466b2fc288db.1726046181.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99c8719b79814cab3fd43519591dcc41c978a48c ]
Even though bareudp transports L3 data (typically IP or MPLS), it needs
to reset the mac_header pointer, so that other parts of the stack don't
mistakenly access the outer header after the packet has been
decapsulated.
This allows to push an Ethernet header to bareudp packets and redirect
them to an Ethernet device:
$ tc filter add dev bareudp0 ingress matchall \
action vlan push_eth dst_mac 00:00:5e:00:53:01 \
src_mac 00:00:5e:00:53:00 \
action mirred egress redirect dev eth0
Without this patch, push_eth refuses to add an ethernet header because
the skb appears to already have a MAC header.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 45fa29c85117 ("bareudp: Pull inner IP header in bareudp_udp_encap_recv().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c09b50efcad985cf920ca88baa9aa52b1999dcc ]
After calling m_can_stop() an interrupt may be pending or NAPI might
still be executed. This means the driver might still touch registers
of the IP core after the clocks have been disabled. This is not good
practice and might lead to aborts depending on the SoC integration.
To avoid these potential problems, make m_can_close() symmetric to
m_can_open(), i.e. stop the clocks at the end, right before shutting
down the transceiver.
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-2-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d836cb5fe045463cdab15ad6f278f7c7c194228f ]
Add support for implementing transceiver node as phy. The max_bitrate
is obtained by getting a phy attribute.
Link: https://lore.kernel.org/r/20210724174001.553047-1-mkl@pengutronix.de
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: 2c09b50efcad ("can: m_can: m_can_close(): stop clocks after device has been shut down")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d7c6ae1efb1ff68bc01d79d94fdf0388f86cdd8 ]
In the `wilc_parse_join_bss_param` function, the TSF field of the `ies`
structure is accessed after the RCU read-side critical section is
unlocked. According to RCU usage rules, this is illegal. Reusing this
pointer can lead to unpredictable behavior, including accessing memory
that has been updated or causing use-after-free issues.
This possible bug was identified using a static analysis tool developed
by myself, specifically designed to detect RCU-related issues.
To address this, the TSF value is now stored in a local variable
`ies_tsf` before the RCU lock is released. The `param->tsf_lo` field is
then assigned using this local variable, ensuring that the TSF value is
safely accessed.
Fixes: 205c50306acf ("wifi: wilc1000: fix RCU usage in connect path")
Signed-off-by: Jiawei Ye <jiawei.ye@foxmail.com>
Reviewed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/tencent_466225AA599BA49627FB26F707EE17BC5407@qq.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e735a4c6137262bcefe45bb52fde7b1f5fc6c4d ]
In 'rtw_wait_firmware_completion()', always wait for both (regular and
wowlan) firmware loading attempts. Otherwise if 'rtw_usb_intf_init()'
has failed in 'rtw_usb_probe()', 'rtw_usb_disconnect()' may issue
'ieee80211_free_hw()' when one of 'rtw_load_firmware_cb()' (usually
the wowlan one) is still in progress, causing UAF detected by KASAN.
Fixes: c8e5695eae99 ("rtw88: load wowlan firmware if wowlan is supported")
Reported-by: syzbot+6c6c08700f9480c41fe3@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6c6c08700f9480c41fe3
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240726114657.25396-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a84454f5204718ca5b4ad2c1f0bf2031e2403d1 ]
There is a WARNING in iwl_trans_wait_tx_queues_empty() (that was
recently converted from just a message), that can be hit if we
wait for TX queues to become empty after firmware died. Clearly,
we can't expect anything from the firmware after it's declared dead.
Don't call iwl_trans_wait_tx_queues_empty() in this case. While it could
be a good idea to stop the flow earlier, the flush functions do some
maintenance work that is not related to the firmware, so keep that part
of the code running even when the firmware is not running.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.a7cbd794cee9.I44a739fbd4ffcc46b83844dd1c7b2eb0c7b270f6@changeid
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4186c8d9e6af57bab0687b299df10ebd47534a0a ]
The driver must ensure TX descriptor updates are visible
before updating TX pointer and TX clear pointer.
This resolves TX hangs observed on AST2600 when running
iperf3.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbd7ec083413c6a2e0c326d49e24ec7d12c7a9e0 ]
When sending packets under 60 bytes, up to three bytes of the buffer
following the data may be leaked. Avoid this by extending all packets to
ETH_ZLEN, ensuring nothing is leaked in the padding. This bug can be
reproduced by running
$ ping -s 11 destination
Fixes: 9ad1a3749333 ("dpaa_eth: add support for DPAA Ethernet")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240910143144.1439910-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7617d62cba4a8a3ff3ed3fda0171c43f135c142e ]
Add MLX5E_1000BASE_T and MLX5E_100BASE_TX to the legacy
modes in ptys2legacy_ethtool_table, since they were missing.
Fixes: 665bc53969d7 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e843cf7b34fe2e0c1afc55e1f3057375c9b77a14 ]
When adding a switch filter (such as a MAC or VLAN filter), it is expected
that the driver will detect the case where the filter already exists, and
return -EEXIST. This is used by calling code such as ice_vc_add_mac_addr,
and ice_vsi_add_vlan to avoid incrementing the accounting fields such as
vsi->num_vlan or vf->num_mac.
This logic works correctly for the case where only a single VSI has added a
given switch filter.
When a second VSI adds the same switch filter, the driver converts the
existing filter from an ICE_FWD_TO_VSI filter into an ICE_FWD_TO_VSI_LIST
filter. This saves switch resources, by ensuring that multiple VSIs can
re-use the same filter.
The ice_add_update_vsi_list() function is responsible for doing this
conversion. When first converting a filter from the FWD_TO_VSI into
FWD_TO_VSI_LIST, it checks if the VSI being added is the same as the
existing rule's VSI. In such a case it returns -EEXIST.
However, when the switch rule has already been converted to a
FWD_TO_VSI_LIST, the logic is different. Adding a new VSI in this case just
requires extending the VSI list entry. The logic for checking if the rule
already exists in this case returns 0 instead of -EEXIST.
This breaks the accounting logic mentioned above, so the counters for how
many MAC and VLAN filters exist for a given VF or VSI no longer accurately
reflect the actual count. This breaks other code which relies on these
counts.
In typical usage this primarily affects such filters generally shared by
multiple VSIs such as VLAN 0, or broadcast and multicast MAC addresses.
Fix this by correctly reporting -EEXIST in the case of adding the same VSI
to a switch rule already converted to ICE_FWD_TO_VSI_LIST.
Fixes: 9daf8208dd4d ("ice: Add support for switch filter programming")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de7a670f8defe4ed2115552ad23dea0f432f7be4 ]
When the vsc73xx mdio bus work properly, the generic autonegotiation
configuration works well.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
