[ Upstream commit 1057812d146dd658c9a9a96d869c2551150207b5 ]
In case of a reset triggered by the QCA7000 itself, the behavior of the
qca_spi driver was not quite correct:
- in case of a pending RX frame decoding the drop counter must be
incremented and decoding state machine reseted
- also the reset counter must always be incremented regardless of sync
state
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231206141222.52029-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96a7e861d9e04d07febd3011c30cd84cd141d81f ]
After calling ethtool -g it was not possible to adjust the TX ring
size again:
# ethtool -g eth1
Ring parameters for eth1:
Pre-set maximums:
RX: 4
RX Mini: n/a
RX Jumbo: n/a
TX: 10
Current hardware settings:
RX: 4
RX Mini: n/a
RX Jumbo: n/a
TX: 10
# ethtool -G eth1 tx 8
netlink error: Invalid argument
The reason for this is that the readonly setting rx_pending get
initialized and after that the range check in qcaspi_set_ringparam()
fails regardless of the provided parameter. So fix this by accepting
the exposed RX defaults. Instead of adding another magic number
better use a new define here.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231206141222.52029-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4e6064c97c050bd9904925ff7d53d0c9954fc7b ]
The qca_spi driver stop and restart the SPI kernel thread
(via ndo_stop & ndo_open) in case of TX ring changes. This is
a big issue because it allows userspace to prevent restart of
the SPI kernel thread (via signals). A subsequent change of
TX ring wrongly assume a valid spi_thread pointer which result
in a crash.
So prevent this by stopping the network traffic handling and
temporary park the SPI thread.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231206141222.52029-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b0768b6556af56ee9b7cf4e68452a2b6289ae45 ]
When FIFO reaches near full state, device will issue pause frame.
If pause slot is enabled(set to 1), in this time, device will issue
pause frame only once. But if pause slot is disabled(set to 0), device
will keep sending pause frames until FIFO reaches near empty state.
When pause slot is disabled, if there is no one to handle receive
packets, device FIFO will reach near full state and keep sending
pause frames. That will impact entire local area network.
This issue can be reproduced in Chromebox (not Chromebook) in
developer mode running a test image (and v5.10 kernel):
1) ping -f $CHROMEBOX (from workstation on same local network)
2) run "powerd_dbus_suspend" from command line on the $CHROMEBOX
3) ping $ROUTER (wait until ping fails from workstation)
Takes about ~20-30 seconds after step 2 for the local network to
stop working.
Fix this issue by enabling pause slot to only send pause frame once
when FIFO reaches near full state.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Reported-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20231129155350.5843-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f708aba40f9c1eeb9c7e93ed4863b5f85b09b288 ]
If a xge port just connect with an optical module and no fiber,
it may have a fake link up because there may be interference on
the hardware. This patch adds an anti-shake to avoid the problem.
And the time of anti-shake is base on tests.
Fixes: b917078c1c10 ("net: hns: Add ACPI support to check SFP present")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4115ba677c35f694b62298e55f0e04ce84eed469 ]
Currently ionic_dim_work() is incorrect when in
split interrupt mode. This is because the interrupt
rate is only being changed for the Rx side even for
dim running on Tx. Fix this by using the qcq from
the container_of macro. Also, introduce some local
variables for a bit of cleanup.
Fixes: a6ff85e0a2d9 ("ionic: remove intr coalesce update from napi")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231204192234.21017-3-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ceb3860a67652f9d36dfdecfcd2cb3eb2f4537d ]
Our friendly kernel test robot has reminded us that with a new
check we have a warning about a potential string truncation.
In this case it really doesn't hurt anything, but it is worth
addressing especially since there really is no reason to reserve
so many bytes for our queue names. It seems that cutting the
queue name buffer length in half stops the complaint.
Fixes: c06107cabea3 ("ionic: more ionic name tweaks")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311300201.lO8v7mKU-lkp@intel.com/
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231204192234.21017-2-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d007caaaf052f82ca2340d4c7b32d04a3f5dbf3f ]
When flow_indr_dev_register() fails, bnxt_init_tc will free
bp->tc_info through kfree(). However, the caller function
bnxt_init_one() will ignore this failure and call
bnxt_shutdown_tc() on failure of bnxt_dl_register(), where
a use-after-free happens. Fix this issue by setting
bp->tc_info to NULL after kfree().
Fixes: 627c89d00fb9 ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://lore.kernel.org/r/20231204024004.8245-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d9f22b3d3ef379ed05bd3f3e2de83dfa8da8258 ]
Commit 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set") added
a warning message that reports unexpected size of port's MFS (max
frame size) value. This message use for the port number local
variable 'i' that is wrong.
In i40e_probe() this 'i' variable is used only to iterate VSIs
to find FDIR VSI:
<code>
...
/* if FDIR VSI was set up, start it now */
for (i = 0; i < pf->num_alloc_vsi; i++) {
if (pf->vsi[i] && pf->vsi[i]->type == I40E_VSI_FDIR) {
i40e_vsi_open(pf->vsi[i]);
break;
}
}
...
</code>
So the warning message use for the port number index of FDIR VSI
if this exists or pf->num_alloc_vsi if not.
Fix the message by using 'pf->hw.port' for the port number.
Fixes: 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b17a597fc2f13aaaa0a2780eb7edb9ae7ac9aea ]
Probe of Sohard Arcnet cards fails,
if 2 or more cards are installed in a system.
See kernel log:
[ 2.759203] arcnet: arcnet loaded
[ 2.763648] arcnet:com20020: COM20020 chipset support (by David Woodhouse et al.)
[ 2.770585] arcnet:com20020_pci: COM20020 PCI support
[ 2.772295] com20020 0000:02:00.0: enabling device (0000 -> 0003)
[ 2.772354] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[ 3.071301] com20020 0000:02:00.0 arc0-0 (uninitialized): PCI COM20020: station FFh found at F080h, IRQ 101.
[ 3.071305] com20020 0000:02:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[ 3.071534] com20020 0000:07:00.0: enabling device (0000 -> 0003)
[ 3.071581] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[ 3.369501] com20020 0000:07:00.0: Led pci:green:tx:0-0 renamed to pci:green:tx:0-0_1 due to name collision
[ 3.369535] com20020 0000:07:00.0: Led pci:red:recon:0-0 renamed to pci:red:recon:0-0_1 due to name collision
[ 3.370586] com20020 0000:07:00.0 arc0-0 (uninitialized): PCI COM20020: station E1h found at C000h, IRQ 35.
[ 3.370589] com20020 0000:07:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[ 3.370608] com20020: probe of 0000:07:00.0 failed with error -5
commit 5ef216c1f848 ("arcnet: com20020-pci: add rotary index support")
changes the device name of all COM20020 based PCI cards,
even if only some cards support this:
snprintf(dev->name, sizeof(dev->name), "arc%d-%d", dev->dev_id, i);
The error happens because all Sohard Arcnet cards would be called arc0-0,
since the Sohard Arcnet cards don't have a PLX rotary coder.
I.e. EAE Arcnet cards have a PLX rotary coder,
which sets the first decimal, ensuring unique devices names.
This patch adds two new card feature flags to indicate
which cards support LEDs and the PLX rotary coder.
For EAE based cards the names still depend on the PLX rotary coder
(untested, since missing EAE hardware).
For Sohard based cards, this patch will result in devices
being called arc0, arc1, ... (tested).
Signed-off-by: Thomas Reichinger <thomas.reichinger@sohard.de>
Fixes: 5ef216c1f848 ("arcnet: com20020-pci: add rotary index support")
Link: https://lore.kernel.org/r/20231130113503.6812-1-thomas.reichinger@sohard.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6577b9a551aedb86bca6d4438c28386361845108 ]
There are two issues when handling error case in com20020pci_probe()
1. priv might be not initialized yet when calling com20020pci_remove()
from com20020pci_probe(), since the priv is set at the very last but it
can jump to error handling in the middle and priv remains NULL.
2. memory leak - the net device is allocated in alloc_arcdev but not
properly released if error happens in the middle of the big for loop
[ 1.529110] BUG: kernel NULL pointer dereference, address: 0000000000000008
[ 1.531447] RIP: 0010:com20020pci_remove+0x15/0x60 [com20020_pci]
[ 1.536805] Call Trace:
[ 1.536939] com20020pci_probe+0x3f2/0x48c [com20020_pci]
[ 1.537226] local_pci_probe+0x48/0x80
[ 1.539918] com20020pci_init+0x3f/0x1000 [com20020_pci]
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 6b17a597fc2f ("arcnet: restoring support for multiple Sohard Arcnet cards")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c89f49964375c904cea33c0247467873f4daf2c ]
rndis_filter uses utf8s_to_utf16s() which is provided by setting
NLS, so select NLS to fix the build error:
ERROR: modpost: "utf8s_to_utf16s" [drivers/net/hyperv/hv_netvsc.ko] undefined!
Fixes: 1ce09e899d28 ("hyperv: Add support for setting MAC from within guests")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20231130055853.19069-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9572c949385aa2ef10368287c439bcb7935137c8 ]
All the mailbox messages sent to AF needs to be guarded
by mutex lock. Add the missing lock in otx2_get_pauseparam
function.
Fixes: 75f36270990c ("octeontx2-pf: Support to enable/disable pause frames via ethtool")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59d395ed606d8df14615712b0cdcdadb2d962175 ]
The original change results in a deadlock if jumbo mtu mode is used.
Reason is that the phydev lock is held when rtl_reset_work() is called
here, and rtl_jumbo_config() calls phy_start_aneg() which also tries
to acquire the phydev lock. Fix this by calling rtl_reset_work()
asynchronously.
Fixes: 621735f59064 ("r8169: fix rare issue with broken rx after link-down on RTL8125")
Reported-by: Ian Chen <free122448@hotmail.com>
Tested-by: Ian Chen <free122448@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/caf6a487-ef8c-4570-88f9-f47a659faf33@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80c0576ef179311f624bc450fede30a89afe9792 ]
There are still single reports of systems where ASPM incompatibilities
cause tx timeouts. It's not clear whom to blame, so let's disable
ASPM in case of a tx timeout.
v2:
- add one-time warning for informing the user
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/92369a92-dc32-4529-0509-11459ba0e391@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 59d395ed606d ("r8169: fix deadlock on RTL8125 in jumbo mtu mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88b74831faaee455c2af380382d979fc38e79270 ]
pm_runtime_get_sync() may return an error. In case it returns with an error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9870257a0a338cd8d6c1cddab74e703f490f6779 ]
Fix races between ravb_tx_timeout_work() and functions of net_device_ops
and ethtool_ops by using rtnl_trylock() and rtnl_unlock(). Note that
since ravb_close() is under the rtnl lock and calls cancel_work_sync(),
ravb_tx_timeout_work() should calls rtnl_trylock(). Otherwise, a deadlock
may happen in ravb_tx_timeout_work() like below:
CPU0 CPU1
ravb_tx_timeout()
schedule_work()
...
__dev_close_many()
// Under rtnl lock
ravb_close()
cancel_work_sync()
// Waiting
ravb_tx_timeout_work()
rtnl_lock()
// This is possible to cause a deadlock
If rtnl_trylock() fails, rescheduling the work with sleep for 1 msec.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231127122420.3706751-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91d3d149978ba7b238198dd80e4b823756aa7cfa ]
ndo_stop() is RTNL-protected by net core, and the worker function takes
RTNL as well. Therefore we will deadlock when trying to execute a
pending work synchronously. To fix this execute any pending work
asynchronously. This will do no harm because netif_running() is false
in ndo_stop(), and therefore the work function is effectively a no-op.
However we have to ensure that no task is running or pending after
rtl_remove_one(), therefore add a call to cancel_work_sync().
Fixes: abe5fc42f9ce ("r8169: use RTNL to protect critical sections")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/12395867-1d17-4cac-aa7d-c691938fcddf@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51597219e0cd5157401d4d0ccb5daa4d9961676f ]
When more than 64 VFs are enabled for a PF then mbox communication
between VF and PF is not working as mbox work queueing for few VFs
are skipped due to wrong calculation of VF numbers.
Fixes: d424b6c02415 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930042-5400-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e54d628a2721bfbb002c19f6e8ca6746cec7640f ]
Commit aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.
Fixes: aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f422abe3f23d483cf01f386819f26fb3fe0dbb2b ]
Increase the needed headroom to account for a 64 byte alignment
restriction which, with this patch, we make mandatory on the Tx path.
The case in which the amount of headroom needed is not available is
already handled by the driver which instead sends a S/G frame with the
first buffer only holding the SW and HW annotation areas.
Without this patch, we can empirically see data corruption happening
between Tx and Tx confirmation which sometimes leads to the SW
annotation area being overwritten.
Since this is an old IP where the hardware team cannot help to
understand the underlying behavior, we make the Tx alignment mandatory
for all frames to avoid the crash on Tx conf. Also, remove the comment
that suggested that this is just an optimization.
This patch also sets the needed_headroom net device field to the usual
value that the driver would need on the Tx path:
- 64 bytes for the software annotation area
- 64 bytes to account for a 64 byte aligned buffer address
Fixes: 6e2387e8f19e ("staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver")
Closes: https://lore.kernel.org/netdev/aa784d0c-85eb-4e5d-968b-c8f74fa86be6@gin.de/
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d30fb712e52964f2cf9a9c14cf67078394044837 ]
The rtnl lock also needs to be held before rndis_filter_device_add()
which advertises nvsp_2_vsc_capability / sriov bit, and triggers
VF NIC offering and registering. If VF NIC finished register_netdev()
earlier it may cause name based config failure.
To fix this issue, move the call to rtnl_lock() before
rndis_filter_device_add(), so VF will be registered later than netvsc
/ synthetic NIC, and gets a name numbered (ethX) after netvsc.
Cc: stable@vger.kernel.org
Fixes: e04e7a7bbd4b ("hv_netvsc: Fix a deadlock by getting rtnl lock earlier in netvsc_probe()")
Reported-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c807d6cd089d2f4951baa838081ec5ae3e2360f8 upstream.
When a VF is being exposed form the kernel, it should be marked as "slave"
before exposing to the user-mode. The VF is not usable without netvsc
running as master. The user-mode should never see a VF without the "slave"
flag.
This commit moves the code of setting the slave flag to the time before
VF is exposed to user-mode.
Cc: stable@vger.kernel.org
Fixes: 0c195567a8f6 ("netvsc: transparent VF management")
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85520856466ed6bc3b1ccb013cddac70ceb437db upstream.
If VF NIC is registered earlier, NETDEV_REGISTER event is replayed,
but NETDEV_POST_INIT is not.
Move register_netdevice_notifier() earlier, so the call back
function is set before probing.
Cc: stable@vger.kernel.org
Fixes: e04e7a7bbd4b ("hv_netvsc: Fix a deadlock by getting rtnl lock earlier in netvsc_probe()")
Reported-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd0413bbf8b11f56e8aa842783b0deda0dfe2926 ]
Due to a typo, the code checked the RX checksum feature in the TX path.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20231122004219.3504219-1-samuel.holland@sifive.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a2323ac24a50311f64a3a9b54ed5bef5821ecae ]
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7121205d5330c6a3cb3379348886d47c77b78d06 ]
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 676ec53844cbdf2f47e68a076cdff7f0ec6cbe3f ]
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0739af07d1d947af27c877f797cb82ceee702515 ]
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93da8d75a66568ba4bb5b14ad2833acd7304cd02 ]
wg_xmit() can be called concurrently, KCSAN reported [1]
some device stats updates can be lost.
Use DEV_STATS_INC() for this unlikely case.
[1]
BUG: KCSAN: data-race in wg_xmit / wg_xmit
read-write to 0xffff888104239160 of 8 bytes by task 1375 on cpu 0:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
read-write to 0xffff888104239160 of 8 bytes by task 1378 on cpu 1:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
v2: also change wg_packet_consume_data_done() (Hangbin Liu)
and wg_packet_purge_staged_packets()
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6a26310273c323380da21eb23fcfd50e31140913 upstream.
This reverts commit efa5f1311c4998e9e6317c52bc5ee93b3a0f36df.
I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
was filtered out by the mc filter.
The packet was properly received.
Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02d5fdbf4f2b8c406f7a4c98fa52aa181a11d733 upstream.
Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers using phylink, by calling netif_carrier_off in
phylink_create.
Fixes: 089381b27abe ("leds: initial support for Turris Omnia LEDs")
Cc: stable@vger.kernel.org
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f77c7d605b29df277d77e9ee75d96e7ad145d2d upstream.
The ath11k active pdevs are protected by RCU but the htt pktlog handling
code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019112521.2071-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b6c14833165f689cc5928574ebafe52bbce5f1e upstream.
The ath11k active pdevs are protected by RCU but the DFS radar event
handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019153115.26401-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a5352a81b4720ba43d9c899974e3bddf7ce0ce8 upstream.
The ath11k active pdevs are protected by RCU but the temperature event
handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section as reported by RCU lockdep:
=============================
WARNING: suspicious RCU usage
6.6.0-rc6 #7 Not tainted
-----------------------------
drivers/net/wireless/ath/ath11k/mac.c:638 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
...
Call trace:
...
lockdep_rcu_suspicious+0x16c/0x22c
ath11k_mac_get_ar_by_pdev_id+0x194/0x1b0 [ath11k]
ath11k_wmi_tlv_op_rx+0xa84/0x2c1c [ath11k]
ath11k_htc_rx_completion_handler+0x388/0x510 [ath11k]
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: a41d10348b01 ("ath11k: add thermal sensor device support")
Cc: stable@vger.kernel.org # 5.7
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019153115.26401-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e1caeace0418381f36b3aa8403dfd82fc57fc53 ]
Macvlan device in passthru mode sets its lower device promiscuous mode
according to its MACVLAN_FLAG_NOPROMISC flag instead of synchronizing it to
its own promiscuity setting. However, macvlan_change_rx_flags() function
doesn't check the mode before propagating such changes to the lower device
which can cause net_device->promiscuity counter overflow as illustrated by
reproduction example [0] and resulting dmesg log [1]. Fix the issue by
first verifying the mode in macvlan_change_rx_flags() function before
propagating promiscuous mode change to the lower device.
[0]:
ip link add macvlan1 link enp8s0f0 type macvlan mode passthru
ip link set macvlan1 promisc on
ip l set dev macvlan1 up
ip link set macvlan1 promisc off
ip l set dev macvlan1 down
ip l set dev macvlan1 up
[1]:
[ 5156.281724] macvlan1: entered promiscuous mode
[ 5156.285467] mlx5_core 0000:08:00.0 enp8s0f0: entered promiscuous mode
[ 5156.287639] macvlan1: left promiscuous mode
[ 5156.288339] mlx5_core 0000:08:00.0 enp8s0f0: left promiscuous mode
[ 5156.290907] mlx5_core 0000:08:00.0 enp8s0f0: entered promiscuous mode
[ 5156.317197] mlx5_core 0000:08:00.0 enp8s0f0: promiscuity touches roof, set promiscuity failed. promiscuity feature of device might be broken.
Fixes: efdbd2b30caa ("macvlan: Propagate promiscuity setting to lower devices.")
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20231114175915.1649154-1-vladbu@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2bd0c0264febcd8d47209079a6671c38e6558b ]
Treat the operation as an error case when the return value is equivalent to
the size of the name buffer. Failed to write null terminator to the name
buffer, making the string malformed and should not be used. Provide a
string with only the firmware version when forming the string with the
board id fails. This logic for representors is identical to normal flow
with ethtool.
Without check, will trigger -Wformat-truncation with W=1.
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_rep_get_drvinfo':
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:78:31: warning: '%.16s' directive output may be truncated writing up to 16 bytes into a region of size between 13 and 22 [-Wformat-truncation=]
78 | "%d.%d.%04d (%.16s)",
| ^~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:77:9: note: 'snprintf' output between 12 and 37 bytes into a destination of size 32
77 | snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
78 | "%d.%d.%04d (%.16s)",
| ~~~~~~~~~~~~~~~~~~~~~
79 | fw_rev_maj(mdev), fw_rev_min(mdev),
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
80 | fw_rev_sub(mdev), mdev->board_id);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: cf83c8fdcd47 ("net/mlx5e: Add missing ethtool driver info for representors")
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6d4ab2e97dcfbcd748ae71761a9d8e5e41cc732c
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20231114215846.5902-16-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17a7612b99e66d2539341ab4f888f970c2c7f76d ]
Remove exposed driver version as it was done in other drivers,
so module version will work correctly by displaying the kernel
version for which it is compiled.
And move mlx5_core module name to general include, so auxiliary drivers
will be able to use it as a basis for a name in their device ID tables.
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Stable-dep-of: 1b2bd0c0264f ("net/mlx5e: Check return value of snprintf writing to fw_version buffer for representors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f9b1a0731662648949a1c0587f6acb3b7f8acf1 ]
When mlx5_packet_reformat_alloc() fails, the encap_header allocated in
mlx5e_tc_tun_create_header_ipv4{6} will be released within it. However,
e->encap_header is already set to the previously freed encap_header
before mlx5_packet_reformat_alloc(). As a result, the later
mlx5e_encap_put() will free e->encap_header again, causing a double free
issue.
mlx5e_encap_put()
--> mlx5e_encap_dealloc()
--> kfree(e->encap_header)
This happens when cmd: MLX5_CMD_OP_ALLOC_PACKET_REFORMAT_CONTEXT fail.
This patch fix it by not setting e->encap_header until
mlx5_packet_reformat_alloc() success.
Fixes: d589e785baf5e ("net/mlx5e: Allow concurrent creation of encap entries")
Reported-by: Cruz Zhao <cruzzhao@linux.alibaba.com>
Reported-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa02de9e75889915b554eda1964a631fd019973b ]
The while loop condition verifies 'count < limit'. Neither value change
before the 'count >= limit' check. As is this check is dead code. But
code inspection reveals a code path that modifies 'count' and then goto
'drain_data' and back to 'read_again'. So there is a need to verify
count value sanity after 'read_again'.
Move 'read_again' up to fix the count limit check.
Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/d9486296c3b6b12ab3a0515fcd47d56447a07bfc.1699897370.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc6c0bfbaa947dd7976e30e8c29b10c868b6fa42 ]
The RX max frame size is over 10000 for the Gemini ethernet,
but the TX max frame size is actually just 2047 (0x7ff after
checking the datasheet). Reflect this in what we offer to Linux,
cap the MTU at the TX max frame minus ethernet headers.
We delete the code disabling the hardware checksum for large
MTUs as netdev->mtu can no longer be larger than
netdev->max_mtu meaning the if()-clause in gmac_fix_features()
is never true.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-3-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4d0c5b4d279bfe3585fbd806efefd3e51c82afa ]
The Gemini ethernet controller provides hardware checksumming
for frames up to 1514 bytes including ethernet headers but not
FCS.
If we start sending bigger frames (after first bumping up the MTU
on both interfaces sending and receiving the frames), truncated
packets start to appear on the target such as in this tcpdump
resulting from ping -s 1474:
23:34:17.241983 14:d6:4d:a8:3c:4f (oui Unknown) > bc:ae:c5:6b:a8:3d (oui Unknown),
ethertype IPv4 (0x0800), length 1514: truncated-ip - 2 bytes missing!
(tos 0x0, ttl 64, id 32653, offset 0, flags [DF], proto ICMP (1), length 1502)
OpenWrt.lan > Fecusia: ICMP echo request, id 1672, seq 50, length 1482
If we bypass the hardware checksumming and provide a software
fallback, everything starts working fine up to the max TX MTU
of 2047 bytes, for example ping -s2000 192.168.1.2:
00:44:29.587598 bc:ae:c5:6b:a8:3d (oui Unknown) > 14:d6:4d:a8:3c:4f (oui Unknown),
ethertype IPv4 (0x0800), length 2042:
(tos 0x0, ttl 64, id 51828, offset 0, flags [none], proto ICMP (1), length 2028)
Fecusia > OpenWrt.lan: ICMP echo reply, id 1683, seq 4, length 2008
The bit enabling to bypass hardware checksum (or any of the
"TSS" bits) are undocumented in the hardware reference manual.
The entire hardware checksum unit appears undocumented. The
conclusion that we need to use the "bypass" bit was found by
trial-and-error.
Since no hardware checksum will happen, we slot in a software
checksum fallback.
Check for the condition where we need to compute checksum on the
skb with either hardware or software using == CHECKSUM_PARTIAL instead
of != CHECKSUM_NONE which is an incomplete check according to
<linux/skbuff.h>.
On the D-Link DIR-685 router this fixes a bug on the conduit
interface to the RTL8366RB DSA switch: as the switch needs to add
space for its tag it increases the MTU on the conduit interface
to 1504 and that means that when the router sends packages
of 1500 bytes these get an extra 4 bytes of DSA tag and the
transfer fails because of the erroneous hardware checksumming,
affecting such basic functionality as the LuCI web interface.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-2-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 510e35fb931ffc3b100e5d5ae4595cd3beca9f1a ]
Enumerator 3 is 1548 bytes according to the datasheet.
Not 1542.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-1-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0a2a1b0d631fc460d830f52d06211838874d655 ]
ppp_sync_ioctl allows setting device MRU, but does not sanity check
this input.
Limit to a sane upper bound of 64KB.
No implementation I could find generates larger than 64KB frames.
RFC 2823 mentions an upper bound of PPP over SDL of 64KB based on the
16-bit length field. Other protocols will be smaller, such as PPPoE
(9KB jumbo frame) and PPPoA (18190 maximum CPCS-SDU size, RFC 2364).
PPTP and L2TP encapsulate in IP.
Syzbot managed to trigger alloc warning in __alloc_pages:
if (WARN_ON_ONCE_GFP(order > MAX_ORDER, gfp))
WARNING: CPU: 1 PID: 37 at mm/page_alloc.c:4544 __alloc_pages+0x3ab/0x4a0 mm/page_alloc.c:4544
__alloc_skb+0x12b/0x330 net/core/skbuff.c:651
__netdev_alloc_skb+0x72/0x3f0 net/core/skbuff.c:715
netdev_alloc_skb include/linux/skbuff.h:3225 [inline]
dev_alloc_skb include/linux/skbuff.h:3238 [inline]
ppp_sync_input drivers/net/ppp/ppp_synctty.c:669 [inline]
ppp_sync_receive+0xff/0x680 drivers/net/ppp/ppp_synctty.c:334
tty_ldisc_receive_buf+0x14c/0x180 drivers/tty/tty_buffer.c:390
tty_port_default_receive_buf+0x70/0xb0 drivers/tty/tty_port.c:37
receive_buf drivers/tty/tty_buffer.c:444 [inline]
flush_to_ldisc+0x261/0x780 drivers/tty/tty_buffer.c:494
process_one_work+0x884/0x15c0 kernel/workqueue.c:2630
With call
ioctl$PPPIOCSMRU1(r1, 0x40047452, &(0x7f0000000100)=0x5e6417a8)
Similar code exists in other drivers that implement ppp_channel_ops
ioctl PPPIOCSMRU. Those might also be in scope. Notably excluded from
this are pppol2tp_ioctl and pppoe_ioctl.
This code goes back to the start of git history.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+6177e1f90d92583bcc58@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65e98bb56fa3ce2edb400930c05238c9b380500e ]
Currently the reset process in hns3 and firmware watchdog init process is
asynchronous. We think firmware watchdog initialization is completed
before VF clear the interrupt source. However, firmware initialization
may not complete early. So VF will receive multiple reset interrupts
and fail to reset.
So we add delay before VF interrupt source and 5 ms delay
is enough to avoid second reset interrupt.
Fixes: 427900d27d86 ("net: hns3: fix the timing issue of VF clearing interrupt sources")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbd2f3b20c6ae425665b6975d766e3653d453e73 ]
When a VF is calling hns3_init_mac_addr(), get_mac_addr() may
return fail, then the value of mac_addr_temp is not initialized.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 719639853d88071dfdfd8d9971eca9c283ff314c ]
KMSAN reported the following uninit-value access issue:
=====================================================
BUG: KMSAN: uninit-value in ppp_sync_input drivers/net/ppp/ppp_synctty.c:690 [inline]
BUG: KMSAN: uninit-value in ppp_sync_receive+0xdc9/0xe70 drivers/net/ppp/ppp_synctty.c:334
ppp_sync_input drivers/net/ppp/ppp_synctty.c:690 [inline]
ppp_sync_receive+0xdc9/0xe70 drivers/net/ppp/ppp_synctty.c:334
tiocsti+0x328/0x450 drivers/tty/tty_io.c:2295
tty_ioctl+0x808/0x1920 drivers/tty/tty_io.c:2694
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0x211/0x400 fs/ioctl.c:857
__x64_sys_ioctl+0x97/0xe0 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Uninit was created at:
__alloc_pages+0x75d/0xe80 mm/page_alloc.c:4591
__alloc_pages_node include/linux/gfp.h:238 [inline]
alloc_pages_node include/linux/gfp.h:261 [inline]
__page_frag_cache_refill+0x9a/0x2c0 mm/page_alloc.c:4691
page_frag_alloc_align+0x91/0x5d0 mm/page_alloc.c:4722
page_frag_alloc include/linux/gfp.h:322 [inline]
__netdev_alloc_skb+0x215/0x6d0 net/core/skbuff.c:728
netdev_alloc_skb include/linux/skbuff.h:3225 [inline]
dev_alloc_skb include/linux/skbuff.h:3238 [inline]
ppp_sync_input drivers/net/ppp/ppp_synctty.c:669 [inline]
ppp_sync_receive+0x237/0xe70 drivers/net/ppp/ppp_synctty.c:334
tiocsti+0x328/0x450 drivers/tty/tty_io.c:2295
tty_ioctl+0x808/0x1920 drivers/tty/tty_io.c:2694
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0x211/0x400 fs/ioctl.c:857
__x64_sys_ioctl+0x97/0xe0 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
CPU: 0 PID: 12950 Comm: syz-executor.1 Not tainted 6.6.0-14500-g1c41041124bd #10
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc38 04/01/2014
=====================================================
ppp_sync_input() checks the first 2 bytes of the data are PPP_ALLSTATIONS
and PPP_UI. However, if the data length is 1 and the first byte is
PPP_ALLSTATIONS, an access to an uninitialized value occurs when checking
PPP_UI. This patch resolves this issue by checking the data length.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
