[ Upstream commit d33fe1714a44ff540629b149d8fab4ac6967585c ]
For CONFIG_CPUMASK_OFFSTACK=y kernel, explicit allocation of cpumask
variable on stack is not recommended since it can cause potential stack
overflow.
Instead, kernel code should always use *cpumask_var API(s) to allocate
cpumask var in config-neutral way, leaving allocation strategy to
CONFIG_CPUMASK_OFFSTACK.
Use *cpumask_var API(s) to address it.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Link: https://lore.kernel.org/r/20240331053441.1276826-3-dawei.li@shingroup.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54a4e5c16382e871c01dd82b47e930fdce30406b ]
PHY_ID_KSZ9477 was supported but not added to the device table passed to
MODULE_DEVICE_TABLE.
Fixes: fc3973a1fa09 ("phy: micrel: add Microchip KSZ 9477 Switch PHY support")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad53f5f54f351e967128edbc431f0f26427172cf ]
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c71e3a5cffd5309d7f84444df03d5b72600cc417 ]
An issue was found on the RTL8125b when transmitting small fragmented
packets, whereby invalid entries were inserted into the transmit ring
buffer, subsequently leading to calls to dma_unmap_single() with a null
address.
This was caused by rtl8169_start_xmit() not noticing changes to nr_frags
which may occur when small packets are padded (to work around hardware
quirks) in rtl8169_tso_csum_v2().
To fix this, postpone inspecting nr_frags until after any padding has been
applied.
Fixes: 9020845fb5d6 ("r8169: improve rtl8169_start_xmit")
Cc: stable@vger.kernel.org
Signed-off-by: Ken Milmore <ken.milmore@gmail.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/27ead18b-c23d-4f49-a020-1fc482c5ac95@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd4bdeb4f29027199c68104fbdfa07ad45390cc1 ]
In rtl_tx() the released descriptors are zero'ed by
rtl8169_unmap_tx_skb(). And in the beginning of rtl8169_start_xmit()
we check that enough descriptors are free, therefore there's no way
the DescOwn bit can be set here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/6965d665-6c50-90c5-70e6-0bb335d4ea47@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c71e3a5cffd5 ("r8169: Fix possible ring buffer corruption on fragmented Tx packets.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83c317d7b36bb3858cf1cb86d2635ec3f3bd6ea3 ]
The only time when nr_frags isn't SKB_MAX_FRAGS is when entering
rtl8169_start_xmit(). However we can use SKB_MAX_FRAGS also here
because when queue isn't stopped there should always be room for
MAX_SKB_FRAGS + 1 descriptors.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/3d1f2ad7-31d5-2cac-4f4a-394f8a3cab63@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c71e3a5cffd5 ("r8169: Fix possible ring buffer corruption on fragmented Tx packets.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41294e6a434d4f19e957c55b275ea0324f275009 ]
Improve the following in rtl8169_start_xmit:
- tp->cur_tx can be accessed in parallel by rtl_tx(), therefore
annotate the race by using WRITE_ONCE
- avoid checking stop_queue a second time by moving the doorbell check
- netif_stop_queue() uses atomic operation set_bit() that includes a
full memory barrier on some platforms, therefore use
smp_mb__after_atomic to avoid overhead
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/80085451-3eaf-507a-c7c0-08d607c46fbc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c71e3a5cffd5 ("r8169: Fix possible ring buffer corruption on fragmented Tx packets.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca1ab89cd2d654661f559bd83ad9fc7323cb6c86 ]
We can simplify the for() condition and eliminate variable tx_left.
The change also considers that tp->cur_tx may be incremented by a
racing rtl8169_start_xmit().
In addition replace the write to tp->dirty_tx and the following
smp_mb() with an equivalent call to smp_store_mb(). This implicitly
adds a WRITE_ONCE() to the write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/c2e19e5e-3d3f-d663-af32-13c3374f5def@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c71e3a5cffd5 ("r8169: Fix possible ring buffer corruption on fragmented Tx packets.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a689e34973e8717cd57991c6fcf527dc56062b5 ]
tp->dirty_tx isn't changed outside rtl_tx(). Therefore I see no need
to guarantee a specific order of reading tp->dirty_tx and tp->cur_tx.
Having said that we can remove the memory barrier.
In addition use READ_ONCE() when reading tp->cur_tx because it can
change in parallel to rtl_tx().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/2264563a-fa9e-11b0-2c42-31bc6b8e2790@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c71e3a5cffd5 ("r8169: Fix possible ring buffer corruption on fragmented Tx packets.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de4d4be4fa64ed7b4aa1c613061015bd8fa98b24 ]
Different channels have different TX power settings. rtl8192de is using
the TX power setting from the wrong channel in the 5 GHz band because
_rtl92c_phy_get_rightchnlplace expects an array which includes all the
channel numbers, but it's using an array which includes only the 5 GHz
channel numbers.
Use the array channel_all (defined in rtl8192de/phy.c) instead of
the incorrect channel5g (defined in core.c).
Tested only with rtl8192du, which will use the same TX power code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/c7653517-cf88-4f57-b79a-8edb0a8b32f0@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fba383985354e83474f95f36d7c65feb75dba19d ]
This functions retrieves values by passing a pointer. As the function
that retrieves them can fail before touching the pointers, the variables
must be initialized.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+5186630949e3c55f0799@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240619132816.11526-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 604141c036e1b636e2a71cf6e1aa09d1e45f40c2 ]
In virtio spec 0.95, VIRTIO_NET_F_GUEST_CSUM was designed to handle
partially checksummed packets, and the validation of fully checksummed
packets by the device is independent of VIRTIO_NET_F_GUEST_CSUM
negotiation. However, the specification erroneously stated:
"If VIRTIO_NET_F_GUEST_CSUM is not negotiated, the device MUST set flags
to zero and SHOULD supply a fully checksummed packet to the driver."
This statement is inaccurate because even without VIRTIO_NET_F_GUEST_CSUM
negotiation, the device can still set the VIRTIO_NET_HDR_F_DATA_VALID flag.
Essentially, the device can facilitate the validation of these packets'
checksums - a process known as RX checksum offloading - removing the need
for the driver to do so.
This scenario is currently not implemented in the driver and requires
correction. The necessary specification correction[1] has been made and
approved in the virtio TC vote.
[1] https://lists.oasis-open.org/archives/virtio-comment/202401/msg00011.html
Fixes: 4f49129be6fa ("virtio-net: Set RXCSUM feature if GUEST_CSUM is available")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8c43360f6e424131fa81d3ba8792ad8ff25a09e ]
commit be27b8965297 ("net: stmmac: replace priv->speed with
the portTransmitRate from the tc-cbs parameters") introduced
a problem. When deleting, it prompts "Invalid portTransmitRate
0 (idleSlope - sendSlope)" and exits. Add judgment on cbs.enable.
Only when offload is enabled, speed divider needs to be calculated.
Fixes: be27b8965297 ("net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240617013922.1035854-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d7198278ece01818cd95a3beffbdf8b2a353fa0 ]
The whole mechanism to remember occurred SPI interrupts is not atomic,
which could lead to unexpected behavior. So fix this by using atomic bit
operations instead.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20240614145030.7781-1-wahrenst@gmx.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61752ac69b69ed2e04444d090f6917c77ab36d42 ]
gcc-9 and some other older versions produce a false-positive warning
for zeroing two fields
In file included from include/linux/string.h:369,
from drivers/net/wireless/ath/ath9k/main.c:18:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at drivers/net/wireless/ath/ath9k/main.c:140:3:
include/linux/fortify-string.h:462:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
462 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Using a struct_group seems to reliably avoid the warning and
not make the code much uglier. The combined memset() should even
save a couple of cpu cycles.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-3-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be27b896529787e23a35ae4befb6337ce73fcca0 ]
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 791b4089e326271424b78f2fae778b20e53d071b ]
Move the vxlan_features_check() call to after we verified the packet is
a tunneled VXLAN packet.
Without this, tunneled UDP non-VXLAN packets (for ex. GENENVE) might
wrongly not get offloaded.
In some cases, it worked by chance as GENEVE header is the same size as
VXLAN, but it is obviously incorrect.
Fixes: e3cfc7e6b7bd ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44711b78608c98a3e6b49ce91678cd0917d5349 ]
In lio_vf_rep_copy_packet() pg_info->page is compared to a NULL value,
but then it is unconditionally passed to skb_add_rx_frag() which looks
strange and could lead to null pointer dereference.
lio_vf_rep_copy_packet() call trace looks like:
octeon_droq_process_packets
octeon_droq_fast_process_packets
octeon_droq_dispatch_pkt
octeon_create_recv_info
...search in the dispatch_list...
->disp_fn(rdisp->rinfo, ...)
lio_vf_rep_pkt_recv(struct octeon_recv_info *recv_info, ...)
In this path there is no code which sets pg_info->page to NULL.
So this check looks unneeded and doesn't solve potential problem.
But I guess the author had reason to add a check and I have no such card
and can't do real test.
In addition, the code in the function liquidio_push_packet() in
liquidio/lio_core.c does exactly the same.
Based on this, I consider the most acceptable compromise solution to
adjust this issue by moving skb_add_rx_frag() into conditional scope.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f233f327913 ("liquidio: switchdev support for LiquidIO NIC")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 968fde83841a8c23558dfbd0a0c69d636db52b55 ]
Currently hns3 ring buffer init process would hold cpu too long with big
Tx/Rx ring depth. This could cause soft lockup.
So this patch adds cond_resched() to the process. Then cpu can break to
run other tasks instead of busy looping.
Fixes: a723fb8efe29 ("net: hns3: refine for set ring parameters")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96b2933152fd87b6a41765b2f58b158fde855b6 ]
If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will
not be run. As a consequence, `sfp_hwmon_remove()` is not getting
run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()`
itself checks `sfp->sm_mod_state` anyways, so this check was not
really needed in the first place.
Fixes: d2e816c0293f ("net: sfp: handle module remove outside state machine")
Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cd4bc987abb2823836cbb8f887026011ccddc8a ]
Commit f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
has recently been added to vxlan mainly in the context of source
address snooping/learning so that when it is enabled, an entry in the
FDB is not being created for an invalid address for the corresponding
tunnel endpoint.
Before commit f58f45c1e5b9 vxlan was similarly behaving as geneve in
that it passed through whichever macs were set in the L2 header. It
turns out that this change in behavior breaks setups, for example,
Cilium with netkit in L3 mode for Pods as well as tunnel mode has been
passing before the change in f58f45c1e5b9 for both vxlan and geneve.
After mentioned change it is only passing for geneve as in case of
vxlan packets are dropped due to vxlan_set_mac() returning false as
source and destination macs are zero which for E/W traffic via tunnel
is totally fine.
Fix it by only opting into the is_valid_ether_addr() check in
vxlan_set_mac() when in fact source address snooping/learning is
actually enabled in vxlan. This is done by moving the check into
vxlan_snoop(). With this change, the Cilium connectivity test suite
passes again for both tunnel flavors.
Fixes: f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Bauer <mail@david-bauer.net>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb95f4535489ed830cf9b34b0a891e384d1aee4 ]
In case the firmware sends a notification that claims it has more data
than it has, we will read past that was allocated for the notification.
Remove the print of the buffer, we won't see it by default. If needed,
we can see the content with tracing.
This was reported by KFENCE.
Fixes: bdccdb854f2f ("iwlwifi: mvm: support MFUART dump in case of MFUART assert")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.ba82a01a559e.Ia91dd20f5e1ca1ad380b95e68aebf2794f553d9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60d62757df30b74bf397a2847a6db7385c6ee281 ]
In some versions of cfg80211, the ssids poinet might be a valid one even
though n_ssids is 0. Accessing the pointer in this case will cuase an
out-of-bound access. Fix this by checking n_ssids first.
Fixes: c1a7515393e4 ("iwlwifi: mvm: add adaptive dwell support")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240513132416.6e4d1762bf0d.I5a0e6cc8f02050a766db704d15594c61fe583d45@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87821b67dea87addbc4ab093ba752753b002176a ]
The driver should call iwl_dbg_tlv_free even if debugfs is not defined
since ini mode does not depend on debugfs ifdef.
Fixes: 68f6f492c4fa ("iwlwifi: trans: support loading ini TLVs from external file")
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.c8e3723f55b0.I5e805732b0be31ee6b83c642ec652a34e974ff10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a7aace2899711592327463c1a29ffee44fcc66e ]
We don't actually support >64 even for HE devices, so revert
back to 64. This fixes an issue where the session is refused
because the queue is configured differently from the actual
session later.
Fixes: 514c30696fbc ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.52f7b4cf83aa.If47e43adddf7fe250ed7f5571fbb35d8221c7c47@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2f228d364da95ab58f63a3fedc00d5b2b7db16ab upstream.
Structs rx_desc_92d and rx_fwinfo_92d will not work for big endian
systems.
Delete rx_desc_92d because it's big and barely used, and instead use
the get_rx_desc_rxmcs and get_rx_desc_rxht functions, which work on big
endian systems too.
Fix rx_fwinfo_92d by duplicating four of its members in the correct
order.
Tested only with RTL8192DU, which will use the same code.
Tested only on a little endian system.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/698463da-5ef1-40c7-b744-fa51ad847caf@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7c0f48410f546772ac94a0f7b7291a15c4fc173 upstream.
Some (all?) management frames are incorrectly reported to mac80211 as
decrypted when actually the hardware did not decrypt them. This results
in speeds 3-5 times lower than expected, 20-30 Mbps instead of 100
Mbps.
Fix this by checking the encryption type field of the RX descriptor.
rtw88 does the same thing.
This fix was tested only with rtl8192du, which will use the same code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/4d600435-f0ea-46b0-bdb4-e60f173da8dd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08b5d052d17a89bb8706b2888277d0b682dc1610 upstream.
Don't subtract 1 from the power index. This was added in commit
2fc0b8e5a17d ("rtl8xxxu: Add TX power base values for gen1 parts")
for unknown reasons. The vendor drivers don't do this.
Also correct the calculations of values written to
REG_OFDM0_X{C,D}_TX_IQ_IMBALANCE. According to the vendor driver,
these are used for TX power training.
With these changes rtl8xxxu sets the TX power of RTL8192CU the same
as the vendor driver.
None of this appears to have any effect on my RTL8192CU device.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/6ae5945b-644e-45e4-a78f-4c7d9c987910@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cd4bc987abb2823836cbb8f887026011ccddc8a upstream.
Commit f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
has recently been added to vxlan mainly in the context of source
address snooping/learning so that when it is enabled, an entry in the
FDB is not being created for an invalid address for the corresponding
tunnel endpoint.
Before commit f58f45c1e5b9 vxlan was similarly behaving as geneve in
that it passed through whichever macs were set in the L2 header. It
turns out that this change in behavior breaks setups, for example,
Cilium with netkit in L3 mode for Pods as well as tunnel mode has been
passing before the change in f58f45c1e5b9 for both vxlan and geneve.
After mentioned change it is only passing for geneve as in case of
vxlan packets are dropped due to vxlan_set_mac() returning false as
source and destination macs are zero which for E/W traffic via tunnel
is totally fine.
Fix it by only opting into the is_valid_ether_addr() check in
vxlan_set_mac() when in fact source address snooping/learning is
actually enabled in vxlan. This is done by moving the check into
vxlan_snoop(). With this change, the Cilium connectivity test suite
passes again for both tunnel flavors.
Fixes: f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Bauer <mail@david-bauer.net>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Backport note: vxlan snooping/learning not supported in 6.8 or older,
so commit is simply a revert. ]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf0497f53c8535f99b72041529d3f7708a6e2c0d ]
When fec_probe() fails or fec_drv_remove() needs to release the
fec queue and remove a NAPI context, therefore add a function
corresponding to fec_enet_init() and call fec_enet_deinit() which
does the opposite to release memory and remove a NAPI context.
Fixes: 59d0f7465644 ("net: fec: init multi queue date structure")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240524050528.4115581-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52a2f0608366a629d43dacd3191039c95fef74ba ]
LED Select (LED_SEL) bit in the LED General Purpose IO Configuration
register is used to determine the functionality of external LED pins
(Speed Indicator, Link and Activity Indicator, Full Duplex Link
Indicator). The default value for this bit is 0 when no EEPROM is
present. If a EEPROM is present, the default value is the value of the
LED Select bit in the Configuration Flags of the EEPROM. A USB Reset or
Lite Reset (LRST) will cause this bit to be restored to the image value
last loaded from EEPROM, or to be set to 0 if no EEPROM is present.
While configuring the dual purpose GPIO/LED pins to LED outputs in the
LED General Purpose IO Configuration register, the LED_SEL bit is changed
as 0 and resulting the configured value from the EEPROM is cleared. The
issue is fixed by using read-modify-write approach.
Fixes: f293501c61c5 ("smsc95xx: configure LED outputs")
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Link: https://lore.kernel.org/r/20240523085314.167650-1-Parthiban.Veerasooran@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8021b94b0412c37bcc79027c2e382086b6ce449 ]
enic_set_vf_port assumes that the nl attribute IFLA_PORT_PROFILE
is of length PORT_PROFILE_MAX and that the nl attributes
IFLA_PORT_INSTANCE_UUID, IFLA_PORT_HOST_UUID are of length PORT_UUID_MAX.
These attributes are validated (in the function do_setlink in rtnetlink.c)
using the nla_policy ifla_port_policy. The policy defines IFLA_PORT_PROFILE
as NLA_STRING, IFLA_PORT_INSTANCE_UUID as NLA_BINARY and
IFLA_PORT_HOST_UUID as NLA_STRING. That means that the length validation
using the policy is for the max size of the attributes and not on exact
size so the length of these attributes might be less than the sizes that
enic_set_vf_port expects. This might cause an out of bands
read access in the memcpys of the data of these
attributes in enic_set_vf_port.
Fixes: f8bd909183ac ("net: Add ndo_{set|get}_vf_port support for enic dynamic vnics")
Signed-off-by: Roded Zats <rzats@paloaltonetworks.com>
Link: https://lore.kernel.org/r/20240522073044.33519-1-rzats@paloaltonetworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c74195d5dd977e97556e6fa76909b831c241230 ]
Previously, the driver incorrectly used rx_dropped to report device
buffer exhaustion.
According to the documentation, rx_dropped should not be used to count
packets dropped due to buffer exhaustion, which is the purpose of
rx_missed_errors.
Use rx_missed_errors as intended for counting packets dropped due to
buffer exhaustion.
Fixes: 269e6b3af3bf ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b1c92f8e5371700fada307cc8fd2c51fa7bc8c1 ]
The assignment of pps_enable is protected by tmreg_lock, but the read
operation of pps_enable is not. So the Coverity tool reports a lock
evasion warning which may cause data race to occur when running in a
multithread environment. Although this issue is almost impossible to
occur, we'd better fix it, at least it seems more logically reasonable,
and it also prevents Coverity from continuing to issue warnings.
Fixes: 278d24047891 ("net: fec: ptp: Enable PPS output based on ptp clock")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240521023800.17102-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d50729f1d60bca822ef6d9c1a5fb28d486bd7593 ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
v3: also fix a sparse error ( https://lore.kernel.org/oe-kbuild-all/202405091310.KvncIecx-lkp@intel.com/ )
v2: leave the skb_trim() game because smsc95xx_rx_csum_offload()
needs the csum part. (Jakub)
While we are it, use get_unaligned() in smsc95xx_rx_csum_offload().
Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: UNGLinuxDriver@microchip.com
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509083313.2113832-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 812552808f7ff71133fc59768cdc253c5b8ca1bf ]
This fixes a probably long standing problem in the Cortina
Gemini ethernet driver: there are some paths in the code
where the IRQ registers are written without taking the proper
locks.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509-gemini-ethernet-locking-v1-1-afd00a528b95@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac0a230f719b02432d8c7eba7615ebd691da86f4 ]
Erhard reports netpoll warnings from sungem:
netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll (gem_start_xmit+0x0/0x398)
WARNING: CPU: 1 PID: 1 at net/core/netpoll.c:370 netpoll_send_skb+0x1fc/0x20c
gem_poll_controller() disables interrupts, which may sleep.
We can't sleep in netpoll, it has interrupts disabled completely.
Strangely, gem_poll_controller() doesn't even poll the completions,
and instead acts as if an interrupt has fired so it just schedules
NAPI and exits. None of this has been necessary for years, since
netpoll invokes NAPI directly.
Fixes: fe09bb619096 ("sungem: Spring cleaning and GRO support")
Reported-and-tested-by: Erhard Furtner <erhard_f@mailbox.org>
Link: https://lore.kernel.org/all/20240428125306.2c3080ef@legion
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240508134504.3560956-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05417aa9c0c038da2464a0c504b9d4f99814a23b ]
Some usb drivers set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: c9b37458e956 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506143939.3673865-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9aad6e45c4e7d16b2bb7c3794154b828fb4384b4 ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
I replace one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: 361459cd9642 ("net: usb: aqc111: Implement RX data path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506135546.3641185-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d60eabb82694e58543e2b6366dae3e7465892a5 ]
This loop is supposed to copy the mac address to cmd->addr but the
i++ increment is missing so it copies everything to cmd->addr[0] and
only the last address is recorded.
Fixes: 22bedad3ce11 ("net: convert multicast list to list_head")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/b788be9a-15f5-4cca-a3fe-79df4c8ce7b2@moroto.mountain
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6dd09b3dac89b45d1ea3e3bd035a3859c0369a0 ]
Syzkaller reports [1] hitting a warning which is caused by presence
of a wrong endpoint type at the URB sumbitting stage. While there
was a check for a specific 4th endpoint, since it can switch types
between bulk and interrupt, other endpoints are trusted implicitly.
Similar warning is triggered in a couple of other syzbot issues [2].
Fix the issue by doing a comprehensive check of all endpoints
taking into account difference between high- and full-speed
configuration.
[1] Syzkaller report:
...
WARNING: CPU: 0 PID: 4721 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
carl9170_usb_send_rx_irq_urb+0x273/0x340 drivers/net/wireless/ath/carl9170/usb.c:504
carl9170_usb_init_device drivers/net/wireless/ath/carl9170/usb.c:939 [inline]
carl9170_usb_firmware_finish drivers/net/wireless/ath/carl9170/usb.c:999 [inline]
carl9170_usb_firmware_step2+0x175/0x240 drivers/net/wireless/ath/carl9170/usb.c:1028
request_firmware_work_func+0x130/0x240 drivers/base/firmware_loader/main.c:1107
process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289
worker_thread+0x669/0x1090 kernel/workqueue.c:2436
kthread+0x2e8/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
</TASK>
[2] Related syzkaller crashes:
Link: https://syzkaller.appspot.com/bug?extid=e394db78ae0b0032cb4d
Link: https://syzkaller.appspot.com/bug?extid=9468df99cb63a4a4c4e1
Reported-and-tested-by: syzbot+0ae4804973be759fa420@syzkaller.appspotmail.com
Fixes: a84fab3cbfdc ("carl9170: 802.11 rx/tx processing and usb backend")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Acked-By: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422183355.3785-1-n.zhandarovich@fintech.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c511a9c12674d246916bb16c479d496b76983193 ]
Clang Static Checker (scan-build) warns:
drivers/net/wireless/ath/ath10k/debugfs_sta.c:line 429, column 3
Value stored to 'ret' is never read.
Return 'ret' rather than 'count' when 'ret' stores an error code.
Fixes: ee8b08a1be82 ("ath10k: add debugfs support to get per peer tids log via tracing")
Signed-off-by: Su Hui <suhui@nfschina.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422034243.938962-1-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 954fd908f177604d4cce77e2a88cc50b29bad5ff ]
clang complains that the temporary string for the name passed into
alloc_workqueue() is too short for its contents:
drivers/net/ethernet/qlogic/qed/qed_main.c:1218:3: error: 'snprintf' will always be truncated; specified size is 16, but format string expands to at least 18 [-Werror,-Wformat-truncation]
There is no need for a temporary buffer, and the actual name of a workqueue
is 32 bytes (WQ_NAME_LEN), so just use the interface as intended to avoid
the truncation.
Fixes: 59ccf86fe69a ("qed: Add driver infrastucture for handling mfw requests.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240326223825.4084412-4-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e57b7d62a1b2f496caf0beba81cec3c90fad80d5 ]
Currently host relies on CE interrupts to get notified that
the service ready message is ready. This results in timeout
issue if the interrupt is not fired, due to some unknown
reasons. See below logs:
[76321.937866] ath10k_pci 0000:02:00.0: wmi service ready event not received
...
[76322.016738] ath10k_pci 0000:02:00.0: Could not init core: -110
And finally it causes WLAN interface bring up failure.
Change to give it one more chance here by polling CE rings,
before failing directly.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00157-QCARMSWPZ-1
Fixes: 5e3dd157d7e7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices")
Reported-by: James Prestwood <prestwoj@gmail.com>
Tested-By: James Prestwood <prestwoj@gmail.com> # on QCA6174 hw3.2
Link: https://lore.kernel.org/linux-wireless/304ce305-fbe6-420e-ac2a-d61ae5e6ca1a@gmail.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240227030409.89702-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
