commit 1a1c13303ff6d64e6f718dc8aa614e580ca8d9b4 upstream.
When physical ports are reset (either through link failure or manually
toggled down and up again) that are slaved to a Linux bond with a tunnel
endpoint IP address on the bond device, not all tunnel packets arriving
on the bond port are decapped as expected.
The bond dev assigns the same MAC address to itself and each of its
slaves. When toggling a slave device, the same MAC address is therefore
offloaded to the NFP multiple times with different indexes.
The issue only occurs when re-adding the shared mac. The
nfp_tunnel_add_shared_mac() function has a conditional check early on
that checks if a mac entry already exists and if that mac entry is
global: (entry && nfp_tunnel_is_mac_idx_global(entry->index)). In the
case of a bonded device (For example br-ex), the mac index is obtained,
and no new index is assigned.
We therefore modify the conditional in nfp_tunnel_add_shared_mac() to
check if the port belongs to the LAG along with the existing checks to
prevent a new global mac index from being re-assigned to the slave port.
Fixes: 20cce8865098 ("nfp: flower: enable MAC address sharing for offloadable devs")
CC: stable@vger.kernel.org # 5.1+
Signed-off-by: Daniel de Villiers <daniel.devilliers@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3d4f7f2288901ed2392695919b3c0e24c1b4084 upstream.
The 1st and 2nd expansion BAR configuration registers are configured,
when the driver starts up, in variables 'barcfg_msix_general' and
'barcfg_msix_xpb', respectively. The 'LengthSelect' field is ORed in
from bit 0, which is incorrect. The 'LengthSelect' field should
start from bit 27.
This has largely gone un-noticed because
NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT happens to be 0.
Fixes: 4cb584e0ee7d ("nfp: add CPP access core")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Daniel Basilio <daniel.basilio@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc9432c4fb159a3913e0ce3173b8218cd5bad2e0 upstream.
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO read-only state. This allows users with GPIOs that
never sleepbeing called in atomic context.
Implement the same mechanism as in commit 52af318c93e97 ("mmc: Allow
non-sleeping GPIO cd").
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240206083912.2543142-1-alexander.stein@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93cd256ab224c2519e7c4e5f58bb4f1ac2bf0965 upstream.
Some people are seeing a warning similar to this when using a crystal:
max310x 11-006c: clock is not stable yet
The datasheet doesn't mention the maximum time to wait for the clock to be
stable when using a crystal, and it seems that the 10ms delay in the driver
is not always sufficient.
Jan Kundrát reported that it took three tries (each separated by 10ms) to
get a stable clock.
Modify behavior to check stable clock ready bit multiple times (20), and
waiting 10ms between each try.
Note: the first draft of the driver originally used a 50ms delay, without
checking the clock stable bit.
Then a loop with 1000 retries was implemented, each time reading the clock
stable bit.
Fixes: 4cf9a888fd3c ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Suggested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://www.spinics.net/lists/linux-serial/msg35773.html
Link: https://lore.kernel.org/all/20240110174015.6f20195fde08e5c9e64e5675@hugovil.com/raw
Link: e5dfe3e4a7
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0419373333c2f2024966d36261fd82a453281e80 upstream.
If regmap_read() returns a non-zero value, the 'val' variable can be left
uninitialized.
Clear it before calling regmap_read() to make sure we properly detect
the clock ready bit.
Fixes: 4cf9a888fd3c ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0526ec5360a48ad3ab2e26e802b0532302a7e11 upstream.
In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the
VMBus channel"), napi_disable was getting called for all channels,
including all subchannels without confirming if they are enabled or not.
This caused hv_netvsc getting hung at napi_disable, when netvsc_probe()
has finished running but nvdev->subchan_work has not started yet.
netvsc_subchan_work() -> rndis_set_subchannel() has not created the
sub-channels and because of that netvsc_sc_open() is not running.
netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which
netvsc_subchan_work did not run.
netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI
cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the
NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the
opposite.
Now during netvsc_device_remove(), when napi_disable is called for those
subchannels, napi_disable gets stuck on infinite msleep.
This fix addresses this problem by ensuring that napi_disable() is not
getting called for non-enabled NAPI struct.
But netif_napi_del() is still necessary for these non-enabled NAPI struct
for cleanup purpose.
Call trace:
[ 654.559417] task:modprobe state:D stack: 0 pid: 2321 ppid: 1091 flags:0x00004002
[ 654.568030] Call Trace:
[ 654.571221] <TASK>
[ 654.573790] __schedule+0x2d6/0x960
[ 654.577733] schedule+0x69/0xf0
[ 654.581214] schedule_timeout+0x87/0x140
[ 654.585463] ? __bpf_trace_tick_stop+0x20/0x20
[ 654.590291] msleep+0x2d/0x40
[ 654.593625] napi_disable+0x2b/0x80
[ 654.597437] netvsc_device_remove+0x8a/0x1f0 [hv_netvsc]
[ 654.603935] rndis_filter_device_remove+0x194/0x1c0 [hv_netvsc]
[ 654.611101] ? do_wait_intr+0xb0/0xb0
[ 654.615753] netvsc_remove+0x7c/0x120 [hv_netvsc]
[ 654.621675] vmbus_remove+0x27/0x40 [hv_vmbus]
Cc: stable@vger.kernel.org
Fixes: ac5047671758 ("hv_netvsc: Disable NAPI before closing the VMBus channel")
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1706686551-28510-1-git-send-email-schakrabarti@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cb81840d8f29b66d9d05c6d7f360c9560f7e2f4 upstream.
The kernel fails when compiling without `CONFIG_REGMAP_I2C` but with
`CONFIG_BMA400`.
```
ld: drivers/iio/accel/bma400_i2c.o: in function `bma400_i2c_probe':
bma400_i2c.c:(.text+0x23): undefined reference to `__devm_regmap_init_i2c'
```
Link: https://download.01.org/0day-ci/archive/20240131/202401311634.FE5CBVwe-lkp@intel.com/config
Fixes: 465c811f1f20 ("iio: accel: Add driver for the BMA400")
Fixes: 9bea10642396 ("iio: accel: bma400: add support for bma400 spi")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240131225246.14169-1-mario.limonciello@amd.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 792595bab4925aa06532a14dd256db523eb4fa5e upstream.
Recently, we encounter kernel crash in function rm3100_common_probe
caused by out of bound access of array rm3100_samp_rates (because of
underlying hardware failures). Add boundary check to prevent out of
bound access.
Fixes: 121354b2eceb ("iio: magnetometer: Add driver support for PNI RM3100")
Suggested-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: zhili.liu <zhili.liu@ucas.com.cn>
Link: https://lore.kernel.org/r/1704157631-3814-1-git-send-email-zhouzhouyi@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6db053cd949fcd6254cea9f2cd5d39f7bd64379c upstream.
Commit 4c3577db3e4f ("Staging: iio: impedance-analyzer: Fix sparse
warning") fixed a compiler warning, but introduced a bug that resulted
in one of the two 16 bit IIO channels always being zero (when both are
enabled).
This is because int is 32 bits wide on most architectures and in the
case of a little-endian machine the two most significant bytes would
occupy the buffer for the second channel as 'val' is being passed as a
void pointer to 'iio_push_to_buffers()'.
Fix by defining 'val' as u16. Tested working on ARM64.
Fixes: 4c3577db3e4f ("Staging: iio: impedance-analyzer: Fix sparse warning")
Signed-off-by: David Schiller <david.schiller@jku.at>
Link: https://lore.kernel.org/r/20240122134916.2137957-1-david.schiller@jku.at
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4e61de63e34860c36a71d1a364edba16fb6203b upstream.
In remoteproc shutdown sequence, rpmsg_remove will get called which
would depopulate all the child nodes that have been created during
rpmsg_probe. This would result in cb_remove call for all the context
banks for the remoteproc. In cb_remove function, session 0 is
getting skipped which is not correct as session 0 will never become
available again. Add changes to mark session 0 also as invalid.
Fixes: f6f9279f2bf0 ("misc: fastrpc: Add Qualcomm fastrpc basic driver model")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Link: https://lore.kernel.org/r/20240108114833.20480-1-quic_ekangupt@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97830f3c3088638ff90b20dfba2eb4d487bf14d7 upstream.
In (e)poll mode, threads often depend on I/O events to determine when
data is ready for consumption. Within binder, a thread may initiate a
command via BINDER_WRITE_READ without a read buffer and then make use
of epoll_wait() or similar to consume any responses afterwards.
It is then crucial that epoll threads are signaled via wakeup when they
queue their own work. Otherwise, they risk waiting indefinitely for an
event leaving their work unhandled. What is worse, subsequent commands
won't trigger a wakeup either as the thread has pending work.
Fixes: 457b9a6f09f0 ("Staging: android: add binder driver")
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Martijn Coenen <maco@android.com>
Cc: Alice Ryhl <aliceryhl@google.com>
Cc: Steven Moreland <smoreland@google.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20240131215347.1808751-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b55984c96ffe9e236eb9c82a2196e0b1f84990d upstream.
Invoking the make_tx_response() / push_tx_responses() pair with no lock
held would be acceptable only if all such invocations happened from the
same context (NAPI instance or dealloc thread). Since this isn't the
case, and since the interface "spec" also doesn't demand that multicast
operations may only be performed with no in-flight transmits,
MCAST_{ADD,DEL} processing also needs to acquire the response lock
around the invocations.
To prevent similar mistakes going forward, "downgrade" the present
functions to private helpers of just the two remaining ones using them
directly, with no forward declarations anymore. This involves renaming
what so far was make_tx_response(), for the new function of that name
to serve the new (wrapper) purpose.
While there,
- constify the txp parameters,
- correct xenvif_idx_release()'s status parameter's type,
- rename {,_}make_tx_response()'s status parameters for consistency with
xenvif_idx_release()'s.
Fixes: 210c34dcd8d9 ("xen-netback: add support for multicast control")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/980c6c3d-e10e-4459-8565-e8fbde122f00@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f9ab17394f831cb7986ec50900fa37507a127f1 upstream.
Against its current description, the kernel API can accepts all types of
directory entries.
This commit corrects the documentation.
Cc: stable@vger.kernel.org
Fixes: 3c2c58cb33b3 ("firewire: core: fw_csr_string addendum")
Link: https://lore.kernel.org/r/20240130100409.30128-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 977fe773dcc7098d8eaf4ee6382cb51e13e784cb upstream.
This reverts commit 1a1975551943f681772720f639ff42fbaa746212.
This commit causes interrupts to be lost for FCoE devices, since it changed
sping locks from "bh" to "irqsave".
Instead, a work queue should be used, and will be addressed in a separate
commit.
Fixes: 1a1975551943 ("scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock")
Signed-off-by: Lee Duncan <lduncan@suse.com>
Link: https://lore.kernel.org/r/c578cdcd46b60470535c4c4a953e6a1feca0dffd.1707500786.git.lduncan@suse.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1c9d0f6f7f1dbf29db996bd8e166242843a5f21 ]
According to the Intel datasheets, software must reset the block
buffer index twice for block process call transactions: once before
writing the outgoing data to the buffer, and once again before
reading the incoming data from the buffer.
The driver is currently missing the second reset, causing the wrong
portion of the block buffer to be read.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Piotr Zakowski <piotr.zakowski@intel.com>
Closes: https://lore.kernel.org/linux-i2c/20240213120553.7b0ab120@endymion.delvare/
Fixes: 315cd67c9453 ("i2c: i801: Add Block Write-Block Read Process Call support")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1d6582f483a4dba4ea03445e6f2f05d9de5bcf ]
If FEATURE_BLOCK_BUFFER is set then bit SMBAUXCTL_E32B is supported
and there's no benefit in reading it back. Origin of this check
seems to be 14 yrs ago when people were not completely sure which
chip versions support the block buffer mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: c1c9d0f6f7f1 ("i2c: i801: Fix block process call transactions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc9ceb90c4b42c6e5c6757df1d6257110433788e ]
When irtoy_command fails, buf should be freed since it is allocated by
irtoy_tx, or there is a memleak.
Fixes: 4114978dcd24 ("media: ir_toy: prevent device from hanging during transmit")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b2d2d7ea0dd09802cf5a0545bf54d8ad8987d20c upstream.
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f17c34ffc792bbb520e4b61baa16b6cfc7d44b13 upstream.
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 7d2d641c44269 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device")
Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2840143e393a4ddc1caab4372969ea337371168c upstream.
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8ec ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d6708bf0d3dd976460d435373cf5abf21ce258 upstream.
If a input device is opened before hid_hw_start is called, events may
not be received from the hardware. In the case of USB-backed devices,
for example, the hid_hw_start function is responsible for filling in
the URB which is submitted when the input device is opened. If a device
is opened prematurely, polling will never start because the device will
not have been in the correct state to send the URB.
Because the wacom driver registers its input devices before calling
hid_hw_start, there is a window of time where a device can be opened
and end up in an inoperable state. Some ARM-based Chromebooks in particular
reliably trigger this bug.
This commit splits the wacom_register_inputs function into two pieces.
One which is responsible for setting up the allocated inputs (and runs
prior to hid_hw_start so that devices are ready for any input events
they may end up receiving) and another which only registers the devices
(and runs after hid_hw_start to ensure devices can be immediately opened
without issue). Note that the functions to initialize the LEDs and remotes
are also moved after hid_hw_start to maintain their own dependency chains.
Fixes: 7704ac937345 ("HID: wacom: implement generic HID handling for pen generic devices")
Cc: stable@vger.kernel.org # v3.18+
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab41a31dd5e2681803642b6d08590b61867840ec upstream.
The xf86-input-wacom driver does not treat '0' as a valid serial
number and will drop any input report which contains an
MSC_SERIAL = 0 event. The kernel driver already takes care to
avoid sending any MSC_SERIAL event if the value of serial[0] == 0
(which is the case for devices that don't actually report a
serial number), but this is not quite sufficient.
Only the lower 32 bits of the serial get reported to userspace,
so if this portion of the serial is zero then there can still
be problems.
This commit allows the driver to report either the lower 32 bits
if they are non-zero or the upper 32 bits otherwise.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Fixes: f85c9dc678a5 ("HID: wacom: generic: Support tool ID and additional tool types")
CC: stable@vger.kernel.org # v4.10
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c73729b64bb692186da080602cd13612783f52ac ]
The function i40e_pf_wait_queues_disabled() iterates all PF's VSIs
up to 'pf->hw.func_caps.num_vsis' but this is incorrect because
the real number of VSIs can be up to 'pf->num_alloc_vsi' that
can be higher. Fix this loop.
Fixes: 69129dc39fac ("i40e: Modify Tx disable wait flow in case of DCB reconfiguration")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3aa619a8b4706f35cb62f780c14e68796b37f3f ]
Since commit 24778be20f87 ("spi: convert drivers to use
bits_per_word_mask") the bits_per_word variable is only written to. The
check that was there before isn't needed any more as the spi core
ensures that only 8 bit transfers are used, so the variable can go away
together with all assignments to it.
Fixes: 24778be20f87 ("spi: convert drivers to use bits_per_word_mask")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 607aad1e4356c210dbef9022955a3089377909b2 ]
If CONFIG_OF_KOBJ is not set, a device_node does not contain a
kobj and attempts to access the embedded kobj via kref_read break
the compile.
Replace affected kref_read calls with a macro that reads the
refcount if it exists and returns 1 if there is no embedded kobj.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401291740.VP219WIz-lkp@intel.com/
Fixes: 4dde83569832 ("of: Fix double free in of_parse_phandle_with_args_map")
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Link: https://lore.kernel.org/r/20240129192556.403271-1-lk@c--e.de
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1ce2654d87e2fb91fea83b288bd9b2641045e42a upstream.
DDPP is copied from Synopsys Data book:
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The macro name should be XGMAC_DPP_DISABLE.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240203053133.1129236-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1692b9775e745f84b69dc8ad0075b0855a43db4e upstream.
The cited commit introduces and uses the string constants dpp_tx_err and
dpp_rx_err. These are assigned to constant fields of the array
dwxgmac3_error_desc.
It has been reported that on GCC 6 and 7.5.0 this results in warnings
such as:
.../dwxgmac2_core.c:836:20: error: initialiser element is not constant
{ true, "TDPES0", dpp_tx_err },
I have been able to reproduce this using: GCC 7.5.0, 8.4.0, 9.4.0 and 10.5.0.
But not GCC 13.2.0.
So it seems this effects older compilers but not newer ones.
As Jon points out in his report, the minimum compiler supported by
the kernel is GCC 5.1, so it does seem that this ought to be fixed.
It is not clear to me what combination of 'const', if any, would address
this problem. So this patch takes of using #defines for the string
constants
Compile tested only.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/c25eb595-8d91-40ea-9f52-efa15ebafdbc@nvidia.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402081135.lAxxBXHk-lkp@intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208-xgmac-const-v1-1-e69a1eeabfc8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d8df0f5f79f747d75a7d356d9b9ea40a4e4c8a9 upstream.
Use kzalloc() to allocate new zeroed out msg node instead of
memsetting a node allocated with kmalloc().
Signed-off-by: Prathu Baronia <prathubaronia2011@gmail.com>
Message-Id: <20230522085019.42914-1-prathubaronia2011@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Ajay Kaher <ajay.kaher@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 683cd8259a9b883a51973511f860976db2550a6e upstream.
After commit 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in
translated mode") the keyboard on Dell XPS 13 9350 / 9360 / 9370 models
has stopped working after a suspend/resume.
The problem appears to be that atkbd_probe() fails when called
from atkbd_reconnect() on resume, which on systems where
ATKBD_CMD_GETID is skipped can only happen by ATKBD_CMD_SETLEDS
failing. ATKBD_CMD_SETLEDS failing because ATKBD_CMD_GETID was
skipped is weird, but apparently that is what is happening.
Fix this by also skipping ATKBD_CMD_SETLEDS when skipping
ATKBD_CMD_GETID.
Fixes: 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in translated mode")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/linux-input/0aa4a61f-c939-46fe-a572-08022e8931c7@molgen.mpg.de/
Closes: https://bbs.archlinux.org/viewtopic.php?pid=2146300
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218424
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2260517
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240126160724.13278-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a60e6c3918d20848906ffcdfcf72ca6a8cfbcf2e upstream.
When closing the laptop lid with an external screen connected, the mouse
pointer has a constant movement to the lower right corner. Opening the
lid again stops this movement, but after that the touchpad does no longer
register clicks.
The touchpad is connected both via i2c-hid and PS/2, the predecessor of
this device (NS70MU) has the same layout in this regard and also strange
behaviour caused by the psmouse and the i2c-hid driver fighting over
touchpad control. This fix is reusing the same workaround by just
disabling the PS/2 aux port, that is only used by the touchpad, to give the
i2c-hid driver the lone control over the touchpad.
v2: Rebased on current master
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231205163602.16106-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 520b391e3e813c1dd142d1eebb3ccfa6d08c3995 upstream.
Upstream commit bac1ec551434 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11
Fixes: bac1ec551434 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12b17b4eb82a41977eb848048137b5908d52845c upstream.
The device IMST USB-Stick for Smart Meter is a rebranded IMST iM871A-USB
Wireless M-Bus USB-adapter. It is used to read wireless water, gas and
electricity meters.
Signed-off-by: Leonard Dallmayr <leonard.dallmayr@mailbox.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4e6c9011990726f4d175e2cdfebe5b0b8cce4839 ]
Commit 4373534a9850 ("scsi: core: Move scsi_host_busy() out of host lock
for waking up EH handler") intended to fix a hard lockup issue triggered by
EH. The core idea was to move scsi_host_busy() out of the host lock when
processing individual commands for EH. However, a suggested style change
inadvertently caused scsi_host_busy() to remain under the host lock. Fix
this by calling scsi_host_busy() outside the lock.
Fixes: 4373534a9850 ("scsi: core: Move scsi_host_busy() out of host lock for waking up EH handler")
Cc: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240203024521.2006455-1-ming.lei@redhat.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdaf0c8629d4524a168cb9e4ad4231875749b28c ]
Before commit 7108b80a542b ("hwmon/coretemp: Handle large core ID
value"), there is a fixed mapping between
1. cpu_core_id
2. the index in pdata->core_data[] array
3. the sysfs attr name, aka "tempX_"
The later two always equal cpu_core_id + 2.
After the commit, pdata->core_data[] index is got from ida so that it
can handle sparse core ids and support more cores within a package.
However, the commit erroneously maps the sysfs attr name to
pdata->core_data[] index instead of cpu_core_id + 2.
As a result, the code is not aligned with the comments, and brings user
visible changes in hwmon sysfs on systems with sparse core id.
For example, before commit 7108b80a542b ("hwmon/coretemp: Handle large
core ID value"),
/sys/class/hwmon/hwmon2/temp2_label:Core 0
/sys/class/hwmon/hwmon2/temp3_label:Core 1
/sys/class/hwmon/hwmon2/temp4_label:Core 2
/sys/class/hwmon/hwmon2/temp5_label:Core 3
/sys/class/hwmon/hwmon2/temp6_label:Core 4
/sys/class/hwmon/hwmon3/temp10_label:Core 8
/sys/class/hwmon/hwmon3/temp11_label:Core 9
after commit,
/sys/class/hwmon/hwmon2/temp2_label:Core 0
/sys/class/hwmon/hwmon2/temp3_label:Core 1
/sys/class/hwmon/hwmon2/temp4_label:Core 2
/sys/class/hwmon/hwmon2/temp5_label:Core 3
/sys/class/hwmon/hwmon2/temp6_label:Core 4
/sys/class/hwmon/hwmon2/temp7_label:Core 8
/sys/class/hwmon/hwmon2/temp8_label:Core 9
Restore the previous behavior and rework the code, comments and variable
names to avoid future confusions.
Fixes: 7108b80a542b ("hwmon/coretemp: Handle large core ID value")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20240202092144.71180-3-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e440abc894585a34c2904a32cd54af1742311b3 ]
Fix a bug that pdata->cpu_map[] is set before out-of-bounds check.
The problem might be triggered on systems with more than 128 cores per
package.
Fixes: 7108b80a542b ("hwmon/coretemp: Handle large core ID value")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240202092144.71180-2-rui.zhang@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stable-dep-of: fdaf0c8629d4 ("hwmon: (coretemp) Fix bogus core_id to attr name mapping")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1168491e7f53581ba7b6014a39a49cfbbb722feb ]
the ASPEED_PTCR_RESULT Register can only hold the result for a
single fan input. Adding a mutex to protect the register until the
reading is done.
Signed-off-by: Loic Prylli <lprylli@netflix.com>
Signed-off-by: Alexander Hansen <alexander.hansen@9elements.com>
Fixes: 2d7a548a3eff ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Link: https://lore.kernel.org/r/121d888762a1232ef403cf35230ccf7b3887083a.1699007401.git.alexander.hansen@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3616173bf9be9bf39d131b120d6eea4e6324cb5 ]
When alloc_scq fails, card->vcs[0] (i.e. vc) should be freed. Otherwise,
in the following call chain:
idt77252_init_one
|-> idt77252_dev_open
|-> open_card_ubr0
|-> alloc_scq [failed]
|-> deinit_card
|-> vfree(card->vcs);
card->vcs is freed and card->vcs[0] is leaked.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46eba193d04f8bd717e525eb4110f3c46c12aec3 ]
Commit 56e58d6c8a56 ("net: stmmac: Implement Safety Features in
XGMAC core") checks and reports safety errors, but leaves the
Data Path Parity Errors for each channel in DMA unhandled at all, lead to
a storm of interrupt.
Fix it by checking and clearing the DMA_DPP_Interrupt_Status register.
Fixes: 56e58d6c8a56 ("net: stmmac: Implement Safety Features in XGMAC core")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcccdafd91f8bdde568b86ff70848cf83f029add ]
MSA MISC0 bit 1 to 7 contains Colorimetry Indicator Field.
dp_link_get_colorimetry_config() returns wrong colorimetry value
in the DP_TEST_DYNAMIC_RANGE_CEA case in the current implementation.
Hence fix this problem by having dp_link_get_colorimetry_config()
return defined CEA RGB colorimetry value in the case of
DP_TEST_DYNAMIC_RANGE_CEA.
Changes in V2:
-- drop retrieving colorimetry from colorspace
-- drop dr = link->dp_link.test_video.test_dyn_range assignment
Changes in V3:
-- move defined MISCr0a Colorimetry vale to dp_reg.h
-- rewording commit title
-- rewording commit text to more precise describe this patch
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/574888/
Link: https://lore.kernel.org/r/1705526010-597-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7104ba0f1958adb250319e68a15eff89ec4fd36d ]
If the external phy working together with phy-omap-usb2 does not implement
send_srp(), we may still attempt to call it. This can happen on an idle
Ethernet gadget triggering a wakeup for example:
configfs-gadget.g1 gadget.0: ECM Suspend
configfs-gadget.g1 gadget.0: Port suspended. Triggering wakeup
...
Unable to handle kernel NULL pointer dereference at virtual address
00000000 when execute
...
PC is at 0x0
LR is at musb_gadget_wakeup+0x1d4/0x254 [musb_hdrc]
...
musb_gadget_wakeup [musb_hdrc] from usb_gadget_wakeup+0x1c/0x3c [udc_core]
usb_gadget_wakeup [udc_core] from eth_start_xmit+0x3b0/0x3d4 [u_ether]
eth_start_xmit [u_ether] from dev_hard_start_xmit+0x94/0x24c
dev_hard_start_xmit from sch_direct_xmit+0x104/0x2e4
sch_direct_xmit from __dev_queue_xmit+0x334/0xd88
__dev_queue_xmit from arp_solicit+0xf0/0x268
arp_solicit from neigh_probe+0x54/0x7c
neigh_probe from __neigh_event_send+0x22c/0x47c
__neigh_event_send from neigh_resolve_output+0x14c/0x1c0
neigh_resolve_output from ip_finish_output2+0x1c8/0x628
ip_finish_output2 from ip_send_skb+0x40/0xd8
ip_send_skb from udp_send_skb+0x124/0x340
udp_send_skb from udp_sendmsg+0x780/0x984
udp_sendmsg from __sys_sendto+0xd8/0x158
__sys_sendto from ret_fast_syscall+0x0/0x58
Let's fix the issue by checking for send_srp() and set_vbus() before
calling them. For USB peripheral only cases these both could be NULL.
Fixes: 657b306a7bdf ("usb: phy: add a new driver for omap usb2 phy")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240128120556.8848-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa58cb51318e329d203857f7a191678e60bb714 ]
This dma_alloc_coherent() is undone neither in the remove function, nor in
the error handling path of fsl_qdma_probe().
Switch to the managed version to fix both issues.
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/7f66aa14f59d32b13672dde28602b47deb294e1f.1704621515.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 968bc1d7203d384e72afe34124a1801b7af76514 ]
This dma_alloc_coherent() is undone in the remove function, but not in the
error handling path of fsl_qdma_probe().
Switch to the managed version to fix the issue in the probe and simplify
the remove function.
Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/a0ef5d0f5a47381617ef339df776ddc68ce48173.1704621515.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc9847c9ba134cfe3398011e343dcf6588c1c902 ]
Propagate the TR response status to the device using BCDMA
split-channels. For example CSI-RX driver should be able to check if a
frame was not transferred completely (short packet) and needs to be
discarded.
Fixes: 25dcb5dd7b7c ("dmaengine: ti: New driver for K3 UDMA")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20240103-tr_resp_err-v1-1-2fdf6d48ab92@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b73e43dcd7a8be26880ef8ff336053b29e79dbc5 ]
In case of long format of qDMA command descriptor, there are one frame
descriptor, three entries in the frame list and two data entries. So the
size of dma_pool_create for these three fields should be the same with
the total size of entries respectively, or the contents may be overwritten
by the next allocated descriptor.
Fixes: 7fdf9b05c73b ("dmaengine: fsl-dpaa2-qdma: Add NXP dpaa2 qDMA controller driver for Layerscape SoCs")
Signed-off-by: Guanhua Gao <guanhua.gao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240118162917.2951450-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
