commit 3fa5a0f5b0d69e31c6476cd81afeca3cc25a4927 upstream.
When CONFIG_PM isn't defined we don't have the function
ieee80211_sta_restart() compiled in, but we always need
it now for firmware restart. Move it out of the ifdef.
Fixes: 7d352ccf1e99 ("mac80211: Add support to trigger sta disconnect on hardware restart")
Link: https://lore.kernel.org/r/20220312221957.1fa96c72db51.I8ecaa5f9402fede0272161e0531ab930b97fba3e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 393b6bc174b0dd21bb2a36c13b36e62fc3474a23 upstream.
Avoid potentially crashing in the driver because of uninitialized private data
Fixes: 5b3dc42b1b0d ("mac80211: add support for driver tx power reporting")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/20241002095630.22431-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5953d680f7e96208c29ce4139a0e38de87a57fe ]
If access to offset + length is larger than the skbuff length, then
skb_checksum() triggers BUG_ON().
skb_checksum() internally subtracts the length parameter while iterating
over skbuff, BUG_ON(len) at the end of it checks that the expected
length to be included in the checksum calculation is fully consumed.
Fixes: 7ec3f7b47b8d ("netfilter: nft_payload: add packet mangling support")
Reported-by: Slavin Liu <slavin-ayu@qq.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04c20a9356f283da623903e81e7c6d5df7e4dc3c ]
As documented in skbuff.h, devices with NETIF_F_IPV6_CSUM capability
can only checksum TCP and UDP over IPv6 if the IP header does not
contains extension.
This is enforced for UDP packets emitted from user-space to an IPv6
address as they go through ip6_make_skb(), which calls
__ip6_append_data() where a check is done on the header size before
setting CHECKSUM_PARTIAL.
But the introduction of UDP encapsulation with fou6 added a code-path
where it is possible to get an skb with a partial UDP checksum and an
IPv6 header with extension:
* fou6 adds a UDP header with a partial checksum if the inner packet
does not contains a valid checksum.
* ip6_tunnel adds an IPv6 header with a destination option extension
header if encap_limit is non-zero (the default value is 4).
The thread linked below describes in more details how to reproduce the
problem with GRE-in-UDP tunnel.
Add a check on the network header size in skb_csum_hwoffload_help() to
make sure no IPv6 packet with extension header is handed to a network
device with NETIF_F_IPV6_CSUM capability.
Link: https://lore.kernel.org/netdev/26548921.1r3eYUQgxm@benoit.monin/T/#u
Fixes: aa3463d65e7b ("fou: Add encap ops for IPv6 tunnels")
Signed-off-by: Benoît Monin <benoit.monin@gmx.fr>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/5fbeecfc311ea182aa1d1c771725ab8b4cac515e.1729778144.git.benoit.monin@gmx.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62fafcd63139920eb25b3fbf154177ce3e6f3232 ]
NETIF_F_IP|IPV6_CSUM feature flag indicates UDP and TCP csum offload
while NETIF_F_HW_CSUM feature flag indicates ip generic csum offload
for HW, which includes not only for TCP/UDP csum, but also for other
protocols' csum like GRE's.
However, in skb_csum_hwoffload_help() it only checks features against
NETIF_F_CSUM_MASK(NETIF_F_HW|IP|IPV6_CSUM). So if it's a non TCP/UDP
packet and the features doesn't support NETIF_F_HW_CSUM, but supports
NETIF_F_IP|IPV6_CSUM only, it would still return 0 and leave the HW
to do csum.
This patch is to support ip generic csum processing by checking
NETIF_F_HW_CSUM for all protocols, and check (NETIF_F_IP_CSUM |
NETIF_F_IPV6_CSUM) only for TCP and UDP.
Note that we're using skb->csum_offset to check if it's a TCP/UDP
proctol, this might be fragile. However, as Alex said, for now we
only have a few L4 protocols that are requesting Tx csum offload,
we'd better fix this until a new protocol comes with a same csum
offset.
v1->v2:
- not extend skb->csum_not_inet, but use skb->csum_offset to tell
if it's an UDP/TCP csum packet.
v2->v3:
- add a note in the changelog, as Willem suggested.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 04c20a9356f2 ("net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e95c4384438adeaa772caa560244b1a2efef816 ]
In qdisc_tree_reduce_backlog, Qdiscs with major handle ffff: are assumed
to be either root or ingress. This assumption is bogus since it's valid
to create egress qdiscs with major handle ffff:
Budimir Markovic found that for qdiscs like DRR that maintain an active
class list, it will cause a UAF with a dangling class pointer.
In 066a3b5b2346, the concern was to avoid iterating over the ingress
qdisc since its parent is itself. The proper fix is to stop when parent
TC_H_ROOT is reached because the only way to retrieve ingress is when a
hierarchy which does not contain a ffff: major handle call into
qdisc_lookup with TC_H_MAJ(TC_H_ROOT).
In the scenario where major ffff: is an egress qdisc in any of the tree
levels, the updates will also propagate to TC_H_ROOT, which then the
iteration must stop.
Fixes: 066a3b5b2346 ("[NET_SCHED] sch_api: fix qdisc_tree_decrease_qlen() loop")
Reported-by: Budimir Markovic <markovicbudimir@gmail.com>
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Tested-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
net/sched/sch_api.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241024165547.418570-1-jhs@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d352ccf1e9935b5222ca84e8baeb07a0c8f94b9 ]
Currently in case of target hardware restart, we just reconfig and
re-enable the security keys and enable the network queues to start
data traffic back from where it was interrupted.
Many ath10k wifi chipsets have sequence numbers for the data
packets assigned by firmware and the mac sequence number will
restart from zero after target hardware restart leading to mismatch
in the sequence number expected by the remote peer vs the sequence
number of the frame sent by the target firmware.
This mismatch in sequence number will cause out-of-order packets
on the remote peer and all the frames sent by the device are dropped
until we reach the sequence number which was sent before we restarted
the target hardware
In order to fix this, we trigger a sta disconnect, in case of target
hw restart. After this there will be a fresh connection and thereby
avoiding the dropping of frames by remote peer.
The right fix would be to pull the entire data path into the host
which is not feasible or would need lots of complex changes and
will still be inefficient.
Tested on ath10k using WCN3990, QCA6174
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: 07a6e3b78a65 ("wifi: iwlwifi: mvm: Fix response handling in iwl_mvm_send_recovery_cmd()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13dee10b30c058ee2c58c5da00339cc0d4201aa6 ]
When we reconfigure, the driver might do some things to complete
the reconfiguration. It's strange and could be broken in some
cases because we restart other works (e.g. remain-on-channel and
TX) before this happens, yet only start queues later.
Change this to do the reconfig complete when reconfiguration is
actually complete, not when we've already started doing other
things again.
For iwlwifi, this should fix a race where the reconfig can race
with TX, for ath10k and ath11k that also use this it won't make
a difference because they just start queues there, and mac80211
also stopped the queues and will restart them later as before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cab99f22fe19.Iefe494687f15fd85f77c1b989d1149c8efdfdc36@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: 07a6e3b78a65 ("wifi: iwlwifi: mvm: Fix response handling in iwl_mvm_send_recovery_cmd()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3e046c31441d182b954fc2f57b2dc38c71ad4bc ]
When tracing is disabled, there is no point in asking the user about
enabling tracing of all mac80211 debug messages.
Fixes: 3fae0273168026ed ("mac80211: trace debug messages")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://patch.msgid.link/85bbe38ce0df13350f45714e2dc288cc70947a19.1727179690.git.geert@linux-m68k.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f0ab59e6537c6a8f9e1b355b48f9c05a76e8563 ]
This expands the validation introduced in commit 07bf7908950a ("xfrm:
Validate address prefix lengths in the xfrm selector.")
syzbot created an SA with
usersa.sel.family = AF_UNSPEC
usersa.sel.prefixlen_s = 128
usersa.family = AF_INET
Because of the AF_UNSPEC selector, verify_newsa_info doesn't put
limits on prefixlen_{s,d}. But then copy_from_user_state sets
x->sel.family to usersa.family (AF_INET). Do the same conversion in
verify_newsa_info before validating prefixlen_{s,d}, since that's how
prefixlen is going to be used later on.
Reported-by: syzbot+cc39f136925517aed571@syzkaller.appspotmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f504465970aebb2467da548f7c1efbbf36d0f44b ]
In 'taprio_change()', 'admin' pointer may become dangling due to sched
switch / removal caused by 'advance_sched()', and critical section
protected by 'q->current_entry_lock' is too small to prevent from such
a scenario (which causes use-after-free detected by KASAN). Fix this
by prefer 'rcu_replace_pointer()' over 'rcu_assign_pointer()' to update
'admin' immediately before an attempt to schedule freeing.
Fixes: a3d43c0d56f1 ("taprio: Add support adding an admin schedule")
Reported-by: syzbot+b65e0af58423fc8a73aa@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=b65e0af58423fc8a73aa
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20241018051339.418890-1-dmantipov@yandex.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8469721034300bbb6dec5b4bf32492c95e16a0c ]
The series in the "fixes" tag added the ability to consider L4 attributes
in routing rules.
The dst lookup on the outer packet of encapsulated traffic in the xfrm
code was not adapted to this change, thus routing behavior that relies
on L4 information is not respected.
Pass the ip protocol information when performing dst lookups.
Fixes: a25724b05af0 ("Merge branch 'fib_rules-support-sport-dport-and-proto-match'")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Tested-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64a90991ba8d4e32e3173ddd83d0b24167a5668c ]
There's issue as follows:
KASAN: maybe wild-memory-access in range [0xdead...108-0xdead...10f]
CPU: 3 UID: 0 PID: 2805 Comm: rmmod Tainted: G W
RIP: 0010:proto_unregister+0xee/0x400
Call Trace:
<TASK>
__do_sys_delete_module+0x318/0x580
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
As bnep_init() ignore bnep_sock_init()'s return value, and bnep_sock_init()
will cleanup all resource. Then when remove bnep module will call
bnep_sock_cleanup() to cleanup sock's resource.
To solve above issue just return bnep_sock_init()'s return value in
bnep_exit().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
