[ Upstream commit 0e49cfe364dea4345551516eb2fe53135a10432b ]
There is no "fsl,phy" property in pin controller pincfg nodes:
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,pins' is a required property
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,phy' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: f496e6750083 ("ARM: dts: Add ZII support for ZII i.MX7 RMU2 board")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d355c895fa4ddd8bec15569eee540baeed7df8c5 ]
The RTC and RTT peripherals use the timing domain slow clock (TD_SLCK),
sourced from the 32.768 kHz crystal oscillator or slow rc oscillator.
The previously used Monitoring domain slow clock (MD_SLCK) is sourced
from an internal RC oscillator which is most probably not precise enough
for real time clock purposes.
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Fixes: 5f6b33f46346 ("ARM: dts: sam9x60: add rtt")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/r/20240821055136.6858-1-ada@thorsis.com
[claudiu.beznea: removed () around the last commit description paragraph,
removed " in front of "timing domain slow clock", described that
TD_SLCK can also be sourced from slow rc oscillator]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0df3c7d7a73d75153090637392c0b73a63cdc24a upstream.
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74e1c956a68a65d642447d852e95b3fbb69bebaa ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b972d6b3b46345023aee56a95df8e2c137aa4ee4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edfea889a049abe80f0d55c0365bf60fbade272f ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5694eed98cca5c164ebb5b831b65b4c9eee4b2d5 ]
Add ethernet-phy node so we can drop the deprecated fec phy-reset-gpios
property. The reset-assert-us value is taken from the existing logic
since the fec driver will add an 1ms assert delay per default if
phy-reset-gpios is used and phy-reset-duration is not specified.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: edfea889a049 ("ARM: dts: imx6qdl-kontron-samx6i: fix PHY reset")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cca46f811d0000c1522a5e18ea48c27a15e45c05 ]
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3066a.dtsi'.
Fixes: fadc78062477 ("ARM: dts: rockchip: add rk3066 hdmi nodes")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/8b229dcc-94e4-4bbc-9efc-9d5ddd694532@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ac4c1d794e7ff454d191bbdab7585ed8dbf3758 ]
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-smdk4412.dtb: keypad@100a0000: 'key-A', 'key-B', 'key-C', 'key-D', 'key-E', 'linux,keypad-no-autorepeat' do not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: c9b92dd70107 ("ARM: dts: Add keypad entries to SMDK4412")
Link: https://lore.kernel.org/r/20240312183105.715735-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88208d3cd79821117fd3fb80d9bcab618467d37b ]
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-origen.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: bd08f6277e44 ("ARM: dts: Add keypad entries to Exynos4412 based Origen")
Link: https://lore.kernel.org/r/20240312183105.715735-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87d8e522d6f5a004f0aa06c0def302df65aff296 ]
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4210-smdkv310.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: 0561ceabd0f1 ("ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN")
Link: https://lore.kernel.org/r/20240312183105.715735-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 831e0cd4f9ee15a4f02ae10b67e7fdc10eb2b4fc ]
Fix an obvious spelling error in the PMIC compatible in the MMP2
Brownstone DTS file.
Fixes: 58f1193e6210 ("mfd: max8925: Add dts")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Closes: https://lore.kernel.org/linux-devicetree/1410884282-18041-1-git-send-email-k.kozlowski@samsung.com/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125-brownstone-typo-fix-v2-1-45bc48a0c81c@skole.hr
[krzysztof: Just 10 years to take a patch, not bad! Rephrased commit
msg]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23e85be1ec81647374055f731488cc9a7c013a5c ]
Add regulator nodes vcc-dram and vcc1v2 to the devicetree. These
regulators correspond to U4 and U5 in the schematics:
http://forum.banana-pi.org/t/bpi-m2-zero-schematic-diagram-public/4111
Signed-off-by: Michael Klein <michael@fossekall.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201130183841.136708-1-michael@fossekall.de
Stable-dep-of: 4a0e7f2decbf ("netfilter: nf_tables: do not compare internal table flags on updates")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79978bff2e4b8e05ebdf5fc3ee6b794002393484 ]
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 023bd910d3ab735459f84b22bb99fb9e00bd9d76 ]
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7da7b84fee58c85a6075022023d31edea40e81a1 ]
Drop the phy-reset-duration and phy-reset-gpios deprecated properties and
move reset-gpios under the switch node.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: 023bd910d3ab ("ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3baa4c5143d65ebab2de0d99a395e5f4f1f46608 ]
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0a1dff3 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbed7bbbf ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a2b96e42a0284c4fc03022236f656a085ca714a ]
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx6sx.dtsi#L1108-L1109
Fixes: 1e336aa0c025 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be7e1e5b0f67c58ec4be0a54db23b6a4fa6e2116 ]
There is no such trigger documented or implemented in Linux. It was a
copy & paste mistake.
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: leds: led-wlan:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
'default-off' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
'default-off' does not match '^cpu[0-9]*$'
'default-off' does not match '^hci[0-9]+-power$'
'default-off' does not match '^mmc[0-9]+$'
'default-off' does not match '^phy[0-9]+tx$'
From schema: Documentation/devicetree/bindings/leds/leds-gpio.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858d83ca4b50bbc8693d95cc94310e6d791fb2e6 ]
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3aa1a82fb20ee97597022f6528823a8ab82bde6 ]
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc35e253d032b959d92e12f081db5b00db26ae64 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11ab7ad6f795ae23c398a4a5c56505d3dab27c4c ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0b929f58719fc57a4926ab4fc972f185453d6a5 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c248e535973088ba7071ff6f26ab7951143450af ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fb7b2a2f06bb3f8321cf26c33e4e820c5b238b6 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1d7cc478fb16816de09740e3c323c0c188d58f ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c711b882c262e36895547cddea2c2d56ce611d ]
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f55da4cc37051cda600ea870ce8cf29f1297715 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d4ac04fa7c3f6dc263dba6f575a2ec7a2d4eca8 ]
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84228d5e29dbc7a6be51e221000e1d122125826c ]
The kernel hangs for a good 12 seconds without any info being printed to
dmesg, very early in the boot process, if this regulator is not enabled.
Force-enable it to work around this issue, until we know more about the
underlying problem.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Cc: stable@vger.kernel.org # v5.8+
Link: https://lore.kernel.org/r/20231206221556.15348-2-paul@crapouillou.net
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554557542e709e190eff8a598f0cde02647d533a ]
The XOADC is present at the address 0x197 rather than just 197. It
doesn't change a lot (since the driver hardcodes all register
addresses), but the DT should present correct address anyway.
Fixes: c4b70883ee33 ("ARM: dts: add XOADC and IIO HWMON to APQ8064")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928110309.1212221-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b6a51aab5f5f9f71d2fa16e8b4d530e1643dfcb ]
With subtle timings changes, we can now sometimes get an external abort on
non-linefetch error booting am3 devices at sysc_reset(). This is because
of a missing reset delay needed for the usb target module.
Looks like we never enabled the delay earlier for am3, although a similar
issue was seen earlier with a similar usb setup for dm814x as described in
commit ebf244148092 ("ARM: OMAP2+: Use srst_udelay for USB on dm814x").
Cc: stable@vger.kernel.org
Fixes: 0782e8572ce4 ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09f8ee81b6da5f76de8b83c8bfc4475b54e101e0 ]
Fixed regulator put under "regulators" node will not be populated,
unless simple-bus or something similar is used. Drop the "regulators"
wrapper node to fix this.
Fixes: 2c5e596524e7 ("ARM: dts: Add MDM9615 dtsi")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230924183914.51414-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad37b5e30433afa7a5513e3eb61f69fa0976785 ]
On mapphone devices we may get lots of noise on the micro-USB port in debug
uart mode until the phy-cpcap-usb driver probes. Let's limit the noise by
using overrun-throttle-ms.
Note that there is also a related separate issue where the charger cable
connected may cause random sysrq requests until phy-cpcap-usb probes that
still remains.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
