[ Upstream commit 730bbfaf7d4890bd99e637db7767dc68cfeb24e7 ]
The effective SPI clock frequency should never exceed speed_hz
otherwise this might result in undefined behavior of the SPI device.
Currently the scldiv calculation could violate this constraint.
For the example parameters perclk_rate = 24 MHz and speed_hz = 7 MHz,
the function fsl_lpspi_set_bitrate will determine perscale = 0 and
scldiv = 1, which is a effective SPI clock of 8 MHz.
So fix this by rounding up the quotient of perclk_rate and speed_hz.
While this never change within the loop, we can pull this out.
Fixes: 5314987de5e5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20240804113611.83613-1-wahrenst@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8bd922d924bb4ab6c6c488310157d1a27996f31 ]
Like other SPI controller flags, bits_per_word_mask may be used by a
peripheral driver, so it needs to reflect the capabilities of the
underlying controller.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240708-spi-mux-fix-v1-3-6c8845193128@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce1dac560a74220f2e53845ec0723b562288aed4 ]
While in commit 2dd33f9cec90 ("spi: imx: support DMA for imx35") it was
claimed that DMA works on i.MX25, i.MX31 and i.MX35 the respective
device trees don't add DMA channels. The Reference manuals of i.MX31 and
i.MX25 also don't mention the CSPI core being DMA capable. (I didn't
check the others.)
Since commit e267a5b3ec59 ("spi: spi-imx: Use dev_err_probe for failed
DMA channel requests") this results in an error message
spi_imx 43fa4000.spi: error -ENODEV: can't get the TX DMA channel!
during boot. However that isn't fatal and the driver gets loaded just
fine, just without using DMA.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://patch.msgid.link/20240508095610.2146640-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95d7c452a26564ef0c427f2806761b857106d8c4 ]
The dev_warn to notify about a spurious interrupt was introduced with
the reasoning that these are unexpected. However spurious interrupts
tend to trigger continously and the error message on the serial console
prevents that the core's detection of spurious interrupts kicks in
(which disables the irq) and just floods the console.
Fixes: c64e7efe46b7 ("spi: stm32: make spurious and overrun interrupts visible")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://msgid.link/r/20240521105241.62400-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f788ba457b45b0ce422943fcec9fa35c4587764 ]
There is no need to set the DMA mapped flag of the message if it has
no mapped transfers. Moreover, it may give the code a chance to take
the wrong paths, i.e. to exercise DMA related APIs on unmapped data.
Make __spi_map_msg() to bail earlier on the above mentioned cases.
Fixes: 99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240522171018.3362521-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a20ad45008a7c82f1184dc6dee280096009ece55 ]
The TX buffer in spi_transfer can be a NULL pointer, so the interrupt
handler may end up writing to the invalid memory and cause crashes.
Add a check to trans->tx_buf before using it.
Fixes: 1ce24864bff4 ("spi: mediatek: Only do dma for 4-byte aligned buffers")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240321070942.1587146-2-fshao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de8b6e1c231a95abf95ad097b993d34b31458ec9 ]
Return IRQ_NONE from the interrupt handler when no interrupt was
detected. Because an empty interrupt will cause a null pointer error:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000008
Call trace:
complete+0x54/0x100
hisi_sfc_v3xx_isr+0x2c/0x40 [spi_hisi_sfc_v3xx]
__handle_irq_event_percpu+0x64/0x1e0
handle_irq_event+0x7c/0x1cc
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Link: https://msgid.link/r/20240123071149.917678-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3aa619a8b4706f35cb62f780c14e68796b37f3f ]
Since commit 24778be20f87 ("spi: convert drivers to use
bits_per_word_mask") the bits_per_word variable is only written to. The
check that was there before isn't needed any more as the spi core
ensures that only 8 bit transfers are used, so the variable can go away
together with all assignments to it.
Fixes: 24778be20f87 ("spi: convert drivers to use bits_per_word_mask")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574bf7bbe83794a902679846770f75a9b7f28176 ]
SFDP read shall use the mspi reads when using the bcm_qspi_exec_mem_op()
call. This fixes SFDP parameter page read failures seen with parts that
now use SFDP protocol to read the basic flash parameter table.
Fixes: 5f195ee7d830 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://msgid.link/r/20240109210033.43249-1-kamal.dasu@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5c7bcb499840551cfbe85c6df177ebc50432bf0 ]
Documentation says only DTDL of 200 is allowed for this SoC.
Fixes: 4286db8456f4 ("spi: sh-msiof: Add R-Car Gen 2 and 3 fallback bindings")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://msgid.link/r/20231212081239.14254-1-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424a8166764e462258fdccaaefbdeb07517c8b21 ]
ZynqMP GQSPI driver no longer uses spi-master framework. It had been
converted to use spi-mem framework. So remove driver dependency from
spi-master and replace it with spi-mem.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1699282435-884917-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 75e33c55ae8fb4a177fe07c284665e1d61b02560 upstream.
atmel_spi_dma_map_xfer to never be called in PDC mode. This causes the
driver to silently fail.
This patch changes the conditional to match the behaviour of the
previous commit before the refactor.
Fixes: 5fa5e6dec762 ("spi: atmel: Switch to transfer_one transfer method")
Signed-off-by: Ville Baillie <villeb@bytesnap.co.uk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210921072132.21831-1-villeb@bytesnap.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69e1818ad27bae167eeaaf6829d4a08900ef5153 ]
Commit 5fa5e6dec762 ("spi: atmel: Switch to transfer_one transfer
method") switched to using transfer_one and set_cs. The
core doesn't call set_cs when the chip select lines are gpios. Add the
SPI_MASTER_GPIO_SS flag to the driver to ensure the calls to set_cs
happen since the driver programs configuration registers there.
Fixes: 5fa5e6dec762 ("spi: atmel: Switch to transfer_one transfer method")
Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
Link: https://lore.kernel.org/r/20210629192218.32125-1-dan.sneddon@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: fc70d643a2f6 ("spi: atmel: Fix clock issue when using devices with different polarities")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fa5e6dec762305a783e918a90a05369fc10e346 ]
Switch from using our own transfer_one_message routine to using the one
provided by the SPI core.
Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
Link: https://lore.kernel.org/r/20210602160816.4890-1-dan.sneddon@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: fc70d643a2f6 ("spi: atmel: Fix clock issue when using devices with different polarities")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2ded280a4b1b7bd93e53670528504be08d24967 ]
Zynq QSPI driver has been converted to use spi-mem framework so
add spi-mem to driver kconfig dependencies.
Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1699037031-702858-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3aa5cb264a38ae9bbcce32abca4c155af0456df ]
AHB memory as MMIO should be mapped with ioremap rather than ioremap_wc,
which should have been used initially just to handle unaligned access as
a workaround.
Fixes: d166a73503ef ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20231010201524.2021340-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ec8b010979036c2fe79a64adb6ecc0bd11e91d1 ]
We don't want to use the value of ilog2(0) as dummy.buswidth is 0 when
dummy.nbytes is 0. Since we have no dummy bytes, we don't need to
configure the dummy byte bits per clock register value anyway.
Signed-off-by: "William A. Kennington III" <william@wkennington.com>
Link: https://lore.kernel.org/r/20230922182812.2728066-1-william@wkennington.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 2cdec9c13f81313dd9f41f09c7cdecbfa4bea91d.
Reported issues with the backport, revert for now.
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 19f3d5d13b756b913be582a9e0d0afdeca9c397e.
Reported issues with backport, revert for now.
Signed-off-by: Sasha Levin <sashal@kernel.org>
