[ Upstream commit 5dd17689526971c5ae12bc8398f34bd68cd0499e ]
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5feba71ec9c14a54c3babdc732c5b6866d8ee43 ]
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca082f019d8fbb983f03080487946da714154bae ]
strncat() usage in adf7242_debugfs_init() is wrong.
The size given to strncat() is the maximum number of bytes that can be
written, excluding the trailing NULL.
Here, the size that is passed, DNAME_INLINE_LEN, does not take into account
the size of "adf7242-" that is already in the array.
In order to fix it, use snprintf() instead.
Fixes: 7302b9d90117 ("ieee802154/adf7242: Driver for ADF7242 MAC IEEE802154")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c0b48e01daba5ca58f939a8425855d3f4f2ed14 ]
Add check for return of igb_update_ethtool_nfc_entry so that in case
of any potential errors the memory alocated for input will be freed.
Fixes: 0e71def25281 ("igb: add support of RX network flow classification")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f97eee484e71890131f9c563c5cc6d5a69e4308d ]
KCSAN reported the following data-race bug:
==================================================================
BUG: KCSAN: data-race in rtl8169_poll (drivers/net/ethernet/realtek/r8169_main.c:4430 drivers/net/ethernet/realtek/r8169_main.c:4583) r8169
race at unknown origin, with read to 0xffff888117e43510 of 4 bytes by interrupt on cpu 21:
rtl8169_poll (drivers/net/ethernet/realtek/r8169_main.c:4430 drivers/net/ethernet/realtek/r8169_main.c:4583) r8169
__napi_poll (net/core/dev.c:6527)
net_rx_action (net/core/dev.c:6596 net/core/dev.c:6727)
__do_softirq (kernel/softirq.c:553)
__irq_exit_rcu (kernel/softirq.c:427 kernel/softirq.c:632)
irq_exit_rcu (kernel/softirq.c:647)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1074 (discriminator 14))
asm_sysvec_apic_timer_interrupt (./arch/x86/include/asm/idtentry.h:645)
cpuidle_enter_state (drivers/cpuidle/cpuidle.c:291)
cpuidle_enter (drivers/cpuidle/cpuidle.c:390)
call_cpuidle (kernel/sched/idle.c:135)
do_idle (kernel/sched/idle.c:219 kernel/sched/idle.c:282)
cpu_startup_entry (kernel/sched/idle.c:378 (discriminator 1))
start_secondary (arch/x86/kernel/smpboot.c:210 arch/x86/kernel/smpboot.c:294)
secondary_startup_64_no_verify (arch/x86/kernel/head_64.S:433)
value changed: 0x80003fff -> 0x3402805f
Reported by Kernel Concurrency Sanitizer on:
CPU: 21 PID: 0 Comm: swapper/21 Tainted: G L 6.6.0-rc2-kcsan-00143-gb5cbe7c00aa0 #41
Hardware name: ASRock X670E PG Lightning/X670E PG Lightning, BIOS 1.21 04/26/2023
==================================================================
drivers/net/ethernet/realtek/r8169_main.c:
==========================================
4429
→ 4430 status = le32_to_cpu(desc->opts1);
4431 if (status & DescOwn)
4432 break;
4433
4434 /* This barrier is needed to keep us from reading
4435 * any other fields out of the Rx descriptor until
4436 * we know the status of DescOwn
4437 */
4438 dma_rmb();
4439
4440 if (unlikely(status & RxRES)) {
4441 if (net_ratelimit())
4442 netdev_warn(dev, "Rx ERROR. status = %08x\n",
Marco Elver explained that dma_rmb() doesn't prevent the compiler to tear up the access to
desc->opts1 which can be written to concurrently. READ_ONCE() should prevent that from
happening:
4429
→ 4430 status = le32_to_cpu(READ_ONCE(desc->opts1));
4431 if (status & DescOwn)
4432 break;
4433
As the consequence of this fix, this KCSAN warning was eliminated.
Fixes: 6202806e7c03a ("r8169: drop member opts1_mask from struct rtl8169_private")
Suggested-by: Marco Elver <elver@google.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: nic_swsd@realtek.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/lkml/dc7fc8fa-4ea4-e9a9-30a6-7c83e6b53188@alu.unizg.hr/
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This is at odds with sbalance, which balances this IRQ automatically.
Disable the IRQ affinity feature and leave this up to sbalance.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
[ Upstream commit 92fd39634541eb0a11bf1bafbc8ba92d6ddb8dba ]
Currently, whenever fw issues a change ownership event, the PF that owns
the fw tracer drops its ownership directly and the other PFs try to pick
up the ownership via what MTRC register suggests.
In some cases, driver releases the ownership of the tracer and reacquires
it later on. Whenever the driver releases ownership of the tracer, fw
issues a change ownership event. This event can be delayed and come after
driver has reacquired ownership of the tracer. Thus the late event will
trigger the tracer owner PF to release the ownership again and lead to a
scenario where no PF is owning the tracer.
To prevent the scenario described above, when handling a change
ownership event, do not drop ownership of the tracer directly, instead
read the fw MTRC register to retrieve the up-to-date owner of the tracer
and set it accordingly in driver level.
Fixes: f53aaa31cce7 ("net/mlx5: FW tracer, implement tracer logic")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a70e5cbedaf8ad10528ac9ac114f3ec20f422df ]
In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:
In file included from include/linux/skbuff.h:28,
from include/net/net_namespace.h:43,
from include/linux/netdevice.h:38,
from drivers/net/ethernet/marvell/sky2.c:18:
drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
1257 | dma_unmap_page(&pdev->dev, re->frag_addr[i],
| ^~~~~~~~~~~~~~
In file included from drivers/net/ethernet/marvell/sky2.c:41:
drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
2198 | dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
| ^~~~~~~~~
With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:
#define ETH_JUMBO_MTU 9000
causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 61b40cefe51af005c72dbdcf975a3d166c6e6406 upstream.
In bcm_sf2_mdio_register(), the class_find_device() will call get_device()
to increment reference count for priv->master_mii_bus->dev if
of_mdio_find_bus() succeeds. If mdiobus_alloc() or mdiobus_register()
fails, it will call get_device() twice without decrement reference count
for the device. And it is the same if bcm_sf2_mdio_register() succeeds but
fails in bcm_sf2_sw_probe(), or if bcm_sf2_sw_probe() succeeds. If the
reference count has not decremented to zero, the dev related resource will
not be freed.
So remove the get_device() in bcm_sf2_mdio_register(), and call
put_device() if mdiobus_alloc() or mdiobus_register() fails and in
bcm_sf2_mdio_unregister() to solve the issue.
And as Simon suggested, unwind from errors for bcm_sf2_mdio_register() and
just return 0 if it succeeds to make it cleaner.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231011032419.2423290-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc6f716a5069180c40a8c9b63631e97da34f64a3 upstream.
The hardware provides the indexes of the first and the last available
queue and VF. From the indexes, the driver calculates the numbers of
queues and VFs. In theory, a faulty device might say the last index is
smaller than the first index. In that case, the driver's calculation
would underflow, it would attempt to write to non-existent registers
outside of the ioremapped range and crash.
I ran into this not by having a faulty device, but by an operator error.
I accidentally ran a QE test meant for i40e devices on an ice device.
The test used 'echo i40e > /sys/...ice PCI device.../driver_override',
bound the driver to the device and crashed in one of the wr32 calls in
i40e_clear_hw.
Add checks to prevent underflows in the calculations of num_queues and
num_vfs. With this fix, the wrong device probing reports errors and
returns a failure without crashing.
Fixes: 838d41d92a90 ("i40e: clear all queues and interrupts")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Link: https://lore.kernel.org/r/20231011233334.336092-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f3389c73832ad90b63208c0fc281ad080114c7a upstream.
Driver allocates the LL2 rx buffers from kmalloc()
area to construct the skb using slab_build_skb()
The required size allocation seems to have overlooked
for accounting both skb_shared_info size and device
placement padding bytes which results into the below
panic when doing skb_put() for a standard MTU sized frame.
skbuff: skb_over_panic: text:ffffffffc0b0225f len:1514 put:1514
head:ff3dabceaf39c000 data:ff3dabceaf39c042 tail:0x62c end:0x566
dev:<NULL>
…
skb_panic+0x48/0x4a
skb_put.cold+0x10/0x10
qed_ll2b_complete_rx_packet+0x14f/0x260 [qed]
qed_ll2_rxq_handle_completion.constprop.0+0x169/0x200 [qed]
qed_ll2_rxq_completion+0xba/0x320 [qed]
qed_int_sp_dpc+0x1a7/0x1e0 [qed]
This patch fixes this by accouting skb_shared_info and device
placement padding size bytes when allocating the buffers.
Cc: David S. Miller <davem@davemloft.net>
Fixes: 0a7fb11c23c0 ("qed: Add Light L2 support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0288c3e709e5fabd51e84715c5c798a02f43061a upstream.
When the system boots into the crash dump kernel after a panic, the ice
networking device may still have pending transactions that can cause errors
or machine checks when the device is re-enabled. This can prevent the crash
dump kernel from loading the driver or collecting the crash data.
To avoid this issue, perform a function level reset (FLR) on the ice device
via PCIe config space before enabling it on the crash kernel. This will
clear any outstanding transactions and stop all queues and interrupts.
Restore the config space after the FLR, otherwise it was found in testing
that the driver wouldn't load successfully.
The following sequence causes the original issue:
- Load the ice driver with modprobe ice
- Enable SR-IOV with 2 VFs: echo 2 > /sys/class/net/eth0/device/sriov_num_vfs
- Trigger a crash with echo c > /proc/sysrq-trigger
- Load the ice driver again (or let it load automatically) with modprobe ice
- The system crashes again during pcim_enable_device()
Fixes: 837f08fdecbe ("ice: Add basic driver framework for Intel(R) E800 Series")
Reported-by: Vishal Agrawal <vagrawal@redhat.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Link: https://lore.kernel.org/r/20231011233334.336092-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242e34500a32631f85c2b4eb6cb42a368a39e54f upstream.
Since the introduction of the ice driver the code has been
double-shifting the RSS enabling field, because the define already has
shifts in it and can't have the regular pattern of "a << shiftval &
mask" applied.
Most places in the code got it right, but one line was still wrong. Fix
this one location for easy backports to stable. An in-progress patch
fixes the defines to "standard" and will be applied as part of the
regular -next process sometime after this one.
Fixes: d76a60ba7afb ("ice: Add support for VLANs and offloads")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231010203101.406248-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f8abb863fa5a4cc18955c6a0e17af0ded3e4a76 upstream.
syzbot has found an uninit-value bug triggered by the dm9601 driver [1].
This error happens because the variable res is not updated if the call
to dm_read_shared_word returns an error. In this particular case -EPROTO
was returned and res stayed uninitialized.
This can be avoided by checking the return value of dm_read_shared_word
and propagating the error if the read operation failed.
[1] https://syzkaller.appspot.com/bug?extid=1f53a30781af65d2c955
Cc: stable@vger.kernel.org
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reported-and-tested-by: syzbot+1f53a30781af65d2c955@syzkaller.appspotmail.com
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Fixes: d0374f4f9c35cdfbee0 ("USB: Davicom DM9601 usbnet driver")
Link: https://lore.kernel.org/r/20231009-topic-dm9601_uninit_mdio_read-v2-1-f2fe39739b6c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b5add9af567c44e12196107f0fe106e194034fd ]
The adapter->vf_mvs.l list needs to be initialized even if the list is
empty. Otherwise it will lead to crashes.
Fixes: a1cbb15c1397 ("ixgbe: Add macvlan support for VF")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/ZSADNdIw8zFx1xw2@kadam
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0a8c918daa58700609ebd45e3fcd49965be8bbc ]
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa904 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0412cc846a1ef38697c3f321f9b174da91ecd3b5 ]
Indicate next PN update using update_pn flag in macsec_context.
Offloaded MACsec implementations does not know whether or not the
MACSEC_SA_ATTR_PN attribute was passed for an SA update and assume
that next PN should always updated, but this is not always true.
The PN can be reset to its initial value using the following command:
$ ip macsec set macsec0 tx sa 0 off #octeontx2-pf case
Or, the update PN command will succeed even if the driver does not support
PN updates.
$ ip macsec set macsec0 tx sa 0 pn 1 on #mscc phy driver case
Comparing the initial PN with the new PN value is not a solution. When
the user updates the PN using its initial value the command will
succeed, even if the driver does not support it. Like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 on #mlx5 case
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: e0a8c918daa5 ("net: phy: mscc: macsec: reject PN update requests")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66cf7435a26917c0c4d6245ad9137e7606e84fdf ]
Do not set netback interfaces (vifs) default TX queue size to the ring size.
The TX queue size is not related to the ring size, and using the ring size (32)
as the queue size can lead to packet drops. Note the TX side of the vif
interface in the netback domain is the one receiving packets to be injected
to the guest.
Do not explicitly set the TX queue length to any value when creating the
interface, and instead use the system default. Note that the queue length can
also be adjusted at runtime.
Fixes: f942dc2552b8 ('xen network backend driver')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0b72a2a6432c0ef67ee5ce8d9172a7c20bba25 ]
The mlxsw_sp2_nve_vxlan_learning_set() function is supposed to return
zero on success or negative error codes. So it needs to be type int
instead of bool.
Fixes: 4ee70efab68d ("mlxsw: spectrum_nve: Add support for VXLAN on Spectrum-2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f990874b1c98fe8e57ee9385669f501822979258 ]
If of_clk_add_provider() fails in ca8210_register_ext_clock(),
it calls clk_unregister() to release priv->clk and returns an
error. However, the caller ca8210_probe() then calls ca8210_remove(),
where priv->clk is freed again in ca8210_unregister_ext_clock(). In
this case, a use-after-free may happen in the second time we call
clk_unregister().
Fix this by removing the first clk_unregister(). Also, priv->clk could
be an error code on failure of clk_register_fixed_rate(). Use
IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().
Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Message-ID: <20231007033049.22353-1-dinghao.liu@zju.edu.cn>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
