[ Upstream commit 42fb3acf6826c6764ba79feb6e15229b43fd2f9f ]
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9234a2549cb6ac038bec36cc7c084218e9575513 ]
If phy_read_mmd() fails, the error code stored in 'bmsr' should be returned
instead of 'val' which is likely to be 0.
Fixes: 75f4d8d10e01 ("net: phy: add Broadcom BCM84881 PHY driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/3e1755b0c40340d00e089d6adae5bca2f8c79e53.1727982168.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a842e443ca8184f2dc82ab307b43a8b38defd6a5 ]
When configuring the fiber port, the DP83869 PHY driver incorrectly
calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit
number (10). This corrupts some other memory location -- in case of
arm64 the priv pointer in the same structure.
Since the advertising flags are updated from supported at the end of the
function the incorrect line isn't needed at all and can be removed.
Fixes: a29de52ba2a1 ("net: dp83869: Add ability to advertise Fiber connection")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241002161807.440378-1-inguin@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eae2c136cb624e4050092feb59f18159b4f2512 ]
There is a bug currently when there are more than one VLAN defined
and any reset that affects the PF is initiated, after the reset rebuild
no traffic will pass on any VLAN but the last one created.
This is caused by the iteration though the VLANs during replay each
clearing the vsi_map bitmap of the VSI that is being replayed. The
problem is that during rhe replay, the pointer to the vsi_map bitmap
is used by each successive vlan to determine if it should be replayed
on this VSI.
The logic was that the replay of the VLAN would replace the bit in the map
before the next VLAN would iterate through. But, since the replay copies
the old bitmap pointer to filt_replay_rules and creates a new one for the
recreated VLANS, it does not do this, and leaves the old bitmap broken
to be used to replay the remaining VLANs.
Since the old bitmap will be cleaned up in post replay cleanup, there is
no need to alter it and break following VLAN replay, so don't clear the
bit.
Fixes: 334cb0626de1 ("ice: Implement VSI replay framework")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2b23b6097303ed0ba5f4bc036a1c07b6027af5c6 upstream.
In rxe_comp_queue_pkt() an incoming response packet skb is enqueued to the
resp_pkts queue and then a decision is made whether to run the completer
task inline or schedule it. Finally the skb is dereferenced to bump a 'hw'
performance counter. This is wrong because if the completer task is
already running in a separate thread it may have already processed the skb
and freed it which can cause a seg fault. This has been observed
infrequently in testing at high scale.
This patch fixes this by changing the order of enqueuing the packet until
after the counter is accessed.
Link: https://lore.kernel.org/r/20240329145513.35381-4-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Fixes: 0b1e5b99a48b ("IB/rxe: Add port protocol stats")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
[Sherry: bp to fix CVE-2024-38544. Fix conflict due to missing commit:
dccb23f6c312 ("RDMA/rxe: Split rxe_run_task() into two subroutines")
which is not necessary to backport]
Signed-off-by: Sherry Yang <sherry.yang@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9cf14f5a2746c19455ce9cb44341b5527b5e19c3 ]
The values of the variables xres and yres are placed in strbuf.
These variables are obtained from strbuf1.
The strbuf1 array contains digit characters
and a space if the array contains non-digit characters.
Then, when executing sprintf(strbuf, "%ux%ux8", xres, yres);
more than 16 bytes will be written to strbuf.
It is suggested to increase the size of the strbuf array to 24.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Shumilin <shum.sdl@nppct.ru>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff599ef6970ee000fa5bc38d02fa5ff5f3fc7575 ]
[WHAT & HOW]
se is null checked previously in the same function, indicating
it might be null; therefore, it must be checked when used again.
This fixes 1 FORWARD_NULL issue reported by Coverity.
Acked-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0fd973c108cdc22a384854bc4b3e288a9717bb2 ]
Return -EIO instead of 0 for below erroneous bus attribute operations:
- read a bus attribute without show().
- write a bus attribute without store().
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240724-bus_fix-v2-1-5adbafc698fb@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25fbcd97cf52c3c9824d44b5c56c19673c3dd50 ]
If a pmem device is in a bad status, the driver side could wait for
host ack forever in virtio_pmem_flush(), causing the system to hang.
So add a status check in the beginning of virtio_pmem_flush() to return
early if the device is not activated.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Message-Id: <20240826215313.2673566-1-philipchen@chromium.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4058c39bd176daf11a826802d940d86292a6b02b ]
The issue is that before entering the crash kernel, the DWC USB controller
did not perform operations such as resetting the interrupt mask bits.
After entering the crash kernel,before the USB interrupt handler
registration was completed while loading the DWC USB driver,an GINTSTS_SOF
interrupt was received.This triggered the misroute_irq process within the
GIC handling framework,ultimately leading to the misrouting of the
interrupt,causing it to be handled by the wrong interrupt handler
and resulting in the issue.
Summary:In a scenario where the kernel triggers a panic and enters
the crash kernel,it is necessary to ensure that the interrupt mask
bit is not enabled before the interrupt registration is complete.
If an interrupt reaches the CPU at this moment,it will certainly
not be handled correctly,especially in cases where this interrupt
is reported frequently.
Please refer to the Crashkernel dmesg information as follows
(the message on line 3 was added before devm_request_irq is
called by the dwc2_driver_probe function):
[ 5.866837][ T1] dwc2 JMIC0010:01: supply vusb_d not found, using dummy regulator
[ 5.874588][ T1] dwc2 JMIC0010:01: supply vusb_a not found, using dummy regulator
[ 5.882335][ T1] dwc2 JMIC0010:01: before devm_request_irq irq: [71], gintmsk[0xf300080e], gintsts[0x04200009]
[ 5.892686][ C0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.0-jmnd1.2_RC #18
[ 5.900327][ C0] Hardware name: CMSS HyperCard4-25G/HyperCard4-25G, BIOS 1.6.4 Jul 8 2024
[ 5.908836][ C0] Call trace:
[ 5.911965][ C0] dump_backtrace+0x0/0x1f0
[ 5.916308][ C0] show_stack+0x20/0x30
[ 5.920304][ C0] dump_stack+0xd8/0x140
[ 5.924387][ C0] pcie_xxx_handler+0x3c/0x1d8
[ 5.930121][ C0] __handle_irq_event_percpu+0x64/0x1e0
[ 5.935506][ C0] handle_irq_event+0x80/0x1d0
[ 5.940109][ C0] try_one_irq+0x138/0x174
[ 5.944365][ C0] misrouted_irq+0x134/0x140
[ 5.948795][ C0] note_interrupt+0x1d0/0x30c
[ 5.953311][ C0] handle_irq_event+0x13c/0x1d0
[ 5.958001][ C0] handle_fasteoi_irq+0xd4/0x260
[ 5.962779][ C0] __handle_domain_irq+0x88/0xf0
[ 5.967555][ C0] gic_handle_irq+0x9c/0x2f0
[ 5.971985][ C0] el1_irq+0xb8/0x140
[ 5.975807][ C0] __setup_irq+0x3dc/0x7cc
[ 5.980064][ C0] request_threaded_irq+0xf4/0x1b4
[ 5.985015][ C0] devm_request_threaded_irq+0x80/0x100
[ 5.990400][ C0] dwc2_driver_probe+0x1b8/0x6b0
[ 5.995178][ C0] platform_drv_probe+0x5c/0xb0
[ 5.999868][ C0] really_probe+0xf8/0x51c
[ 6.004125][ C0] driver_probe_device+0xfc/0x170
[ 6.008989][ C0] device_driver_attach+0xc8/0xd0
[ 6.013853][ C0] __driver_attach+0xe8/0x1b0
[ 6.018369][ C0] bus_for_each_dev+0x7c/0xdc
[ 6.022886][ C0] driver_attach+0x2c/0x3c
[ 6.027143][ C0] bus_add_driver+0xdc/0x240
[ 6.031573][ C0] driver_register+0x80/0x13c
[ 6.036090][ C0] __platform_driver_register+0x50/0x5c
[ 6.041476][ C0] dwc2_platform_driver_init+0x24/0x30
[ 6.046774][ C0] do_one_initcall+0x50/0x25c
[ 6.051291][ C0] do_initcall_level+0xe4/0xfc
[ 6.055894][ C0] do_initcalls+0x80/0xa4
[ 6.060064][ C0] kernel_init_freeable+0x198/0x240
[ 6.065102][ C0] kernel_init+0x1c/0x12c
Signed-off-by: Shawn Shao <shawn.shao@jaguarmicro.com>
Link: https://lore.kernel.org/r/20240830031709.134-1-shawn.shao@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4fdcc10092fb244218013bfe8ff01c55d54e8e4 ]
Currently, suspend interrupt is enabled before pullup enable operation.
This will cause a suspend interrupt assert right after pullup DP. This
suspend interrupt is meaningless, so this will ignore such interrupt
by enable it after usb reset completed.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240823073832.1702135-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a54c441b46a0745683c2eef5a359d22856d27323 ]
For i.MX7D DRAM related mux clock, the clock source change should ONLY
be done done in low level asm code without accessing DRAM, and then
calling clk API to sync the HW clock status with clk tree, it should never
touch real clock source switch via clk API, so CLK_SET_PARENT_GATE flag
should NOT be added, otherwise, DRAM's clock parent will be disabled when
DRAM is active, and system will hang.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240607133347.3291040-8-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a9c97ab6b7e85697e0b74e86062192a5ffffd99 ]
Clear vb2_plane's memory related fields in __vb2_plane_dmabuf_put(),
including bytesused, length, fd and data_offset.
Remove the duplicated code in __prepare_dmabuf().
Signed-off-by: Yunke Cao <yunkec@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e51aded92d42784313ba16c12f4f88cc4f973bbb ]
In the switchtec_ntb_add function, it can call switchtec_ntb_init_sndev
function, then &sndev->check_link_status_work is bound with
check_link_status_work. switchtec_ntb_link_notification may be called
to start the work.
If we remove the module which will call switchtec_ntb_remove to make
cleanup, it will free sndev through kfree(sndev), while the work
mentioned above will be used. The sequence of operations that may lead
to a UAF bug is as follows:
CPU0 CPU1
| check_link_status_work
switchtec_ntb_remove |
kfree(sndev); |
| if (sndev->link_force_down)
| // use sndev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in switchtec_ntb_remove.
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43457ada98c824f310adb7bd96bd5f2fcd9a3279 ]
On chipsets with a second 'Integrated Device Function' SMBus controller use
a different adapter-name for the second IDF adapter.
This allows platform glue code which is looking for the primary i801
adapter to manually instantiate i2c_clients on to differentiate
between the 2.
This allows such code to find the primary i801 adapter by name, without
needing to duplicate the PCI-ids to feature-flags mapping from i2c-i801.c.
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 026f84d3fa62d215b11cbeb5a5d97df941e93b5c ]
The Qualcomm SA8775P root ports don't advertise an ACS capability, but they
do provide ACS-like features to disable peer transactions and validate bus
numbers in requests.
Thus, add an ACS quirk for the SA8775P.
Link: https://lore.kernel.org/linux-pci/20240906052228.1829485-1-quic_skananth@quicinc.com
Signed-off-by: Subramanian Ananthanarayanan <quic_skananth@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f92d67e23b8caa81f6322a2bad1d633b00ca000e ]
Driver code is leaking OF node reference from of_get_parent() in
bcm53573_ilp_init(). Usage of of_get_parent() is not needed in the
first place, because the parent node will not be freed while we are
processing given node (triggered by CLK_OF_DECLARE()). Thus fix the
leak by accessing parent directly, instead of of_get_parent().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826065801.17081-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9246b487ab3c3b5993aae7552b7a4c541cc14a49 ]
Add DMA support for audio function of Glenfly Arise chip, which uses
Requester ID of function 0.
Link: https://lore.kernel.org/r/CA2BBD087345B6D1+20240823095708.3237375-1-wangyuli@uniontech.com
Signed-off-by: SiyuLi <siyuli@glenfly.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
[bhelgaas: lower-case hex to match local code, drop unused Device IDs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fbf8d71742557abaf558d8efb96742d442720cc2 upstream.
Calling irq_domain_remove() will lead to freeing the IRQ domain
prematurely. The domain is still referenced and will be attempted to get
used via rmi_free_function_list() -> rmi_unregister_function() ->
irq_dispose_mapping() -> irq_get_irq_data()'s ->domain pointer.
With PaX's MEMORY_SANITIZE this will lead to an access fault when
attempting to dereference embedded pointers, as in Torsten's report that
was faulting on the 'domain->ops->unmap' test.
Fix this by releasing the IRQ domain only after all related IRQs have
been deactivated.
Fixes: 24d28e4f1271 ("Input: synaptics-rmi4 - convert irq distribution to irq_domain")
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Link: https://lore.kernel.org/r/20240222142654.856566-1-minipli@grsecurity.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9efbe2b8f0177fa97bfab290d60858900aa196b ]
This fixes the following issue discovered by code review:
after vqs have been created, a buggy device can send an interrupt.
A control vq callback will then try to schedule control_work which has
not been initialized yet. Similarly for config interrupt. Further, in
and out vq callbacks invoke find_port_by_vq which attempts to take
ports_lock which also has not been initialized.
To fix, init all locks and work before creating vqs.
Message-ID: <ad982e975a6160ad110c623c016041311ca15b4f.1726511547.git.mst@redhat.com>
Fixes: 17634ba25544 ("virtio: console: Add a new MULTIPORT feature, support for generic ports")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dabdfac0e85c8c1e811b10c08742f49285e78a17 ]
The zFCP/NVMe standalone dumper is supposed to release the dump save area
resource as soon as possible but might fail to do so, for instance, if it
crashes. To avoid this situation, register a reboot notifier and ensure
the dump save area resource is released on reboot or power down.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Stable-dep-of: 0b18c852cc6f ("tracing: Have saved_cmdlines arrays all in one allocation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7449ca87312a5b0390b765be65a126e6e5451026 ]
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
See commit 7dd541a3fb34 ("s390: no need to check return value of debugfs_create functions").
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Stable-dep-of: 0b18c852cc6f ("tracing: Have saved_cmdlines arrays all in one allocation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac631873c9e7a50d2a8de457cfc4b9f86666403e ]
The recent change to allow large frames without hardware checksumming
slotted in software checksumming in the driver if hardware could not
do it.
This will however upset TSO (TCP Segment Offloading). Typical
error dumps includes this:
skb len=2961 headroom=222 headlen=66 tailroom=0
(...)
WARNING: CPU: 0 PID: 956 at net/core/dev.c:3259 skb_warn_bad_offload+0x7c/0x108
gemini-ethernet-port: caps=(0x0000010000154813, 0x00002007ffdd7889)
And the packets do not go through.
The TSO implementation is bogus: a TSO enabled driver must propagate
the skb_shinfo(skb)->gso_size value to the TSO engine on the NIC.
Drop the size check and TSO offloading features for now: this
needs to be fixed up properly.
After this ethernet works fine on Gemini devices with a direct connected
PHY such as D-Link DNS-313.
Also tested to still be working with a DSA switch using the Gemini
ethernet as conduit interface.
Link: https://lore.kernel.org/netdev/CANn89iJLfxng1sYL5Zk0mknXpyYQPCp83m3KgD2KJ2_hKCpEUg@mail.gmail.com/
Suggested-by: Eric Dumazet <edumazet@google.com>
Fixes: d4d0c5b4d279 ("net: ethernet: cortina: Handle large frames")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 221af82f606d928ccef19a16d35633c63026f1be upstream.
Since commit 3f8ca2e115e5 ("vhost/scsi: Extract common handling code
from control queue handler") a null pointer dereference bug can be
triggered when guest sends an SCSI AN request.
In vhost_scsi_ctl_handle_vq(), `vc.target` is assigned with
`&v_req.tmf.lun[1]` within a switch-case block and is then passed to
vhost_scsi_get_req() which extracts `vc->req` and `tpg`. However, for
a `VIRTIO_SCSI_T_AN_*` request, tpg is not required, so `vc.target` is
set to NULL in this branch. Later, in vhost_scsi_get_req(),
`vc->target` is dereferenced without being checked, leading to a null
pointer dereference bug. This bug can be triggered from guest.
When this bug occurs, the vhost_worker process is killed while holding
`vq->mutex` and the corresponding tpg will remain occupied
indefinitely.
Below is the KASAN report:
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 PID: 840 Comm: poc Not tainted 6.10.0+ #1
Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS
1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:vhost_scsi_get_req+0x165/0x3a0
Code: 00 fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 2b 02 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 65 30 4c 89 e2 48 c1 ea 03 <0f> b6
04 02 4c 89 e2 83 e2 07 38 d0 7f 08 84 c0 0f 85 be 01 00 00
RSP: 0018:ffff888017affb50 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff88801b000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888017affcb8
RBP: ffff888017affb80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff888017affc88 R14: ffff888017affd1c R15: ffff888017993000
FS: 000055556e076500(0000) GS:ffff88806b100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200027c0 CR3: 0000000010ed0004 CR4: 0000000000370ef0
Call Trace:
<TASK>
? show_regs+0x86/0xa0
? die_addr+0x4b/0xd0
? exc_general_protection+0x163/0x260
? asm_exc_general_protection+0x27/0x30
? vhost_scsi_get_req+0x165/0x3a0
vhost_scsi_ctl_handle_vq+0x2a4/0xca0
? __pfx_vhost_scsi_ctl_handle_vq+0x10/0x10
? __switch_to+0x721/0xeb0
? __schedule+0xda5/0x5710
? __kasan_check_write+0x14/0x30
? _raw_spin_lock+0x82/0xf0
vhost_scsi_ctl_handle_kick+0x52/0x90
vhost_run_work_list+0x134/0x1b0
vhost_task_fn+0x121/0x350
...
</TASK>
---[ end trace 0000000000000000 ]---
Let's add a check in vhost_scsi_get_req.
Fixes: 3f8ca2e115e5 ("vhost/scsi: Extract common handling code from control queue handler")
Signed-off-by: Haoran Zhang <wh1sper@zju.edu.cn>
[whitespace fixes]
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <b26d7ddd-b098-4361-88f8-17ca7f90adf7@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 76959aff14a0012ad6b984ec7686d163deccdc16 ]
When a battery hook returns an error when adding a new battery, then
the battery hook is automatically unregistered.
However the battery hook provider cannot know that, so it will later
call battery_hook_unregister() on the already unregistered battery
hook, resulting in a crash.
Fix this by using the list head to mark already unregistered battery
hooks as already being unregistered so that they can be ignored by
battery_hook_unregister().
Fixes: fa93854f7a7e ("battery: Add the battery hooking API")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20241001212835.341788-3-W_Armin@gmx.de
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86309cbed26139e1caae7629dcca1027d9a28e75 ]
Move the conditional locking from __battery_hook_unregister()
into battery_hook_unregister() and rename the low-level function
to simplify the locking during battery hook removal.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20241001212835.341788-2-W_Armin@gmx.de
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 76959aff14a0 ("ACPI: battery: Fix possible crash when unregistering a battery hook")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ced8e8b8f40accfcce4a2bbd8b150aa76d5eff9a ]
RTL8125 added fields to the tally counter, what may result in the chip
dma'ing these new fields to unallocated memory. Therefore make sure
that the allocated memory area is big enough to hold all of the
tally counter values, even if we use only parts of it.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/741d26a9-2b2b-485d-91d9-ecb302e345b5@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8df9439389a44fb2cc4ef695e08d6a8870b1616c ]
There is a spelling mistake in the struct field tx_underun, rename
it to tx_underrun.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20240909140021.64884-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: ced8e8b8f40a ("r8169: add tally counter fields added with RTL8125")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e93c6320ecde0583de09f3fe801ce8822886fec ]
Add CLK_SET_RATE_PARENT for several branch clocks. Such clocks don't
have a way to change the rate, so set the parent rate instead.
Fixes: 80a18f4a8567 ("clk: qcom: Add display clock controller driver for SM8150 and SM8250")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240804-sm8350-fixes-v1-1-1149dd8399fe@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b44aa559d6c7f4ea591ef9d2352a7250138d62a ]
The RK3066 VOP sets a dma_stop bit when it's done scanning out a frame
and needs the driver to acknowledge that by clearing the bit.
Unless we clear it "between" frames, the RGB output only shows noise
instead of the picture. atomic_flush is the place for it that least
affects other code (doing it on vblank would require converting all
other usages of the reg_lock to spin_(un)lock_irq, which would affect
performance for everyone).
This seems to be a redundant synchronization mechanism that was removed
in later iterations of the VOP hardware block.
Fixes: f4a6de855eae ("drm: rockchip: vop: add rk3066 vop definitions")
Cc: stable@vger.kernel.org
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240624204054.5524-2-val@packett.cool
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ae7a6211fe7251543796d5af971acb8c9e2da9e ]
The RK3399 has a 1024-entry gamma LUT with 10 bits per component on its
"big" VOP and a 256-entry, 8 bit per component LUT on the "little" VOP.
Compared to the RK3288, it no longer requires disabling gamma while
updating the LUT. On the RK3399, the LUT can be updated at any time as
the hardware has two LUT buffers, one can be written while the other is
in use. A swap of the buffers is triggered by writing 1 to the
update_gamma_lut register.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Tested-by: "Milan P. Stanić" <mps@arvanta.net>
Tested-by: Linus Heckemann <git@sphalerite.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019215843.42718-3-sigmaris@gmail.com
Stable-dep-of: 6b44aa559d6c ("drm/rockchip: vop: clear DMA stop bit on RK3066")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ba000d6ae999b99f29afd64814877a5c4406786 ]
The VOP on RK3399 has a different approach from previous versions for
setting a gamma lookup table, using an update_gamma_lut register. As
this differs from RK3288, give RK3399 its own set of "common" register
definitions.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Tested-by: "Milan P. Stanić" <mps@arvanta.net>
Tested-by: Linus Heckemann <git@sphalerite.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019215843.42718-2-sigmaris@gmail.com
Stable-dep-of: 6b44aa559d6c ("drm/rockchip: vop: clear DMA stop bit on RK3066")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c8d604dea437b69a861479b413d629bc9b3da70 ]
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: 36ecbcab84d0 ("i2c: xiic: Implement power management")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8390dc7477e49e4acc9e553f385f4ff59d186efe ]
Replace the pair of functions, devm_clk_get() and clk_prepare_enable(),
with a single function devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 0c8d604dea43 ("i2c: xiic: Fix pm_runtime_set_suspended() with runtime pm enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dbba3f87c7823cf35e63fb7a2449a5d54b3b799 ]
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 0c8d604dea43 ("i2c: xiic: Fix pm_runtime_set_suspended() with runtime pm enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4286cc2c953983d44d248c9de1c81d3a9643345c upstream.
Without the locking amdgpu currently can race between
amdgpu_ctx_set_entity_priority() (via drm_sched_entity_modify_sched()) and
drm_sched_job_arm(), leading to the latter accesing potentially
inconsitent entity->sched_list and entity->num_sched_list pair.
v2:
* Improve commit message. (Philipp)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Fixes: b37aced31eb0 ("drm/scheduler: implement a function to modify sched list")
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Luben Tuikov <ltuikov89@gmail.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: Philipp Stanner <pstanner@redhat.com>
Cc: <stable@vger.kernel.org> # v5.7+
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240913160559.49054-2-tursulin@igalia.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3360d41f4ac490282fddc3ccc0b58679aa5c065d upstream.
On a few platforms such as TI's AM69 device, disable_irq() fails to keep
track of the interrupts that happen between disable_irq() and
enable_irq() and those interrupts are missed. Use the ->irq_unmask() and
->irq_mask() methods instead of ->irq_enable() and ->irq_disable() to
correctly keep track of edges when disable_irq is called.
This solves the issue of disable_irq() not working as expected on such
platforms.
Fixes: 23265442b02b ("ARM: davinci: irq_data conversion.")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240828133207.493961-1-parth105105@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 056301e7c7c886f96d799edd36f3406cc30e1822 upstream.
Like other Asus ExpertBook models the B2502CVA has its keybopard IRQ (1)
described as ActiveLow in the DSDT, which the kernel overrides to EdgeHigh
which breaks the keyboard.
Add the B2502CVA to the irq1_level_low_skip_override[] quirk table to fix
this.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217760
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20240927141606.66826-4-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f80ce0b78c340e332f04a5801dee5e4ac8cfaeb upstream.
Like other Asus Vivobook models the X1704VAP has its keybopard IRQ (1)
described as ActiveLow in the DSDT, which the kernel overrides to EdgeHigh
which breaks the keyboard.
Add the X1704VAP to the irq1_level_low_skip_override[] quirk table to fix
this.
Reported-by: Lamome Julien <julien.lamome@wanadoo.fr>
Closes: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1078696
Closes: https://lore.kernel.org/all/1226760b-4699-4529-bf57-6423938157a3@wanadoo.fr/
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20240927141606.66826-3-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c684771630e64bc39bddffeb65dd8a6612a6b249 upstream.
The adp5589 seems to have the same behavior as similar devices as
explained in commit 910a9f5636f5 ("Input: adp5588-keys - get value from
data out when dir is out").
Basically, when the gpio is set as output we need to get the value from
ADP5589_GPO_DATA_OUT_A register instead of ADP5589_GPI_STATUS_A.
Fixes: 9d2e173644bb ("Input: ADP5589 - new driver for I2C Keypad Decoder and I/O Expander")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20241001-b4-dev-adp5589-fw-conversion-v1-2-fca0149dfc47@analog.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73580e2ee6adfb40276bd420da3bb1abae204e10 upstream.
Driver is leaking an OF node reference obtained from
of_parse_phandle_with_fixed_args().
Fixes: 43e112bb3dea ("rtc: at91sam9: make use of syscon/regmap to access GPBR registers")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240825183103.102904-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 675faf5a14c14a2be0b870db30a70764df81e2df upstream.
The commit b8c43360f6e4 ("net: stmmac: No need to calculate speed divider
when offload is disabled") allows the "port_transmit_rate_kbps" to be
set to a value of 0, which is then passed to the "div_s64" function when
tc-cbs is disabled. This leads to a zero-division error.
When tc-cbs is disabled, the idleslope, sendslope, and credit values the
credit values are not required to be configured. Therefore, adding a return
statement after setting the txQ mode to DCB when tc-cbs is disabled would
prevent a zero-division error.
Fixes: b8c43360f6e4 ("net: stmmac: No need to calculate speed divider when offload is disabled")
Cc: <stable@vger.kernel.org>
Co-developed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: KhaiWenTan <khai.wen.tan@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240918061422.1589662-1-khai.wen.tan@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 129464e86c7445a858b790ac2d28d35f58256bbe upstream.
Move ST2 reading with overflow handling after measurement data
reading.
ST2 register read have to be read after read measurment data,
because it means end of the reading and realease the lock on the data.
Remove ST2 read skip on interrupt based waiting because ST2 required to
be read out at and of the axis read.
Fixes: 57e73a423b1e ("iio: ak8975: add ak09911 and ak09912 support")
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://patch.msgid.link/20240819-ak09918-v4-2-f0734d14cfb9@mainlining.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ade508b545c969c72cd68479f275a5dd640fd8b9 upstream.
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 5.7
Fixes: 3e5770921a88 ("clk: qcom: gcc: Add global clock controller driver for SM8250")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240719134238.312191-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5a85ed88e043474161bbfe54002c89c1cb50ee2 upstream.
in venus_probe, core->work is bound with venus_sys_error_handler, which is
used to handle error. The code use core->sys_err_done to make sync work.
The core->work is started in venus_event_notify.
If we call venus_remove, there might be an unfished work. The possible
sequence is as follows:
CPU0 CPU1
|venus_sys_error_handler
venus_remove |
hfi_destroy |
venus_hfi_destroy |
kfree(hdev); |
|hfi_reinit
|venus_hfi_queues_reinit
|//use hdev
Fix it by canceling the work in venus_remove.
Cc: stable@vger.kernel.org
Fixes: af2c3834c8ca ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4e5af27e6f6a8b0d14bc0d7eb04f4a6c7291586 upstream.
Valid frequencies may result in BCM votes that exceed the max HW value.
Set vote ceiling to BCM_TCS_CMD_VOTE_MASK to ensure the votes aren't
truncated, which can result in lower frequencies than desired.
Fixes: 04053f4d23a4 ("clk: qcom: clk-rpmh: Add IPA clock support")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Imran Shaik <quic_imrashai@quicinc.com>
Link: https://lore.kernel.org/r/20240809-clk-rpmh-bcm-vote-fix-v2-1-240c584b7ef9@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dc5d5d401f5c6cecd97800ffef82e8d17d228f0 upstream.
The sun4i_csi driver doesn't implement link validation for the subdev it
registers, leaving the link between the subdev and its source
unvalidated. Fix it, using the v4l2_subdev_link_validate() helper.
Fixes: 577bbf23b758 ("media: sunxi: Add A10 CSI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
