[ Upstream commit d2b0ca38d362ebf16ca79cd7f309d5bb8b581deb ]
Currently for CCMP256, GCMP128 and GCMP256 ciphers, in ath11k_install_key()
IEEE80211_KEY_FLAG_GENERATE_IV_MGMT is not set. And in ath11k_mac_mgmt_tx_wmi()
a length of IEEE80211_CCMP_MIC_LEN is reserved for all ciphers.
This results in unexpected management frame drop in case either of above 3 ciphers
is used. The reason is, without IEEE80211_KEY_FLAG_GENERATE_IV_MGMT set, mac80211
will not generate CCMP/GCMP headers in frame for ath11k. Also MIC length reserved
is wrong. Such frame is dropped later by hardware:
ath11k_pci 0000:5a:00.0: mac tx mgmt frame, buf id 0
ath11k_pci 0000:5a:00.0: mgmt tx compl ev pdev_id 1, desc_id 0, status 1
From user point of view, we have observed very low throughput due to this issue:
action frames are all dropped so ADDBA response from DUT never reaches AP. AP
can not use aggregation thus throughput is low.
Fix this by setting IEEE80211_KEY_FLAG_GENERATE_IV_MGMT flag and by reserving proper
MIC length for those ciphers.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Tested-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Closes: https://lore.kernel.org/all/CADS+iDX5=JtJr0apAtAQ02WWBxgOFEv8G063vuGYwDTC8AVZaw@mail.gmail.com
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240605014826.22498-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 840c36fa727aea13a2401a5d1d33b722b79df5af ]
Stop dp rx pktlog when entering suspend and reap the mon_status buffer to keep
it empty. During resume restart the reap timer.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-7-git-send-email-kvalo@codeaurora.org
Stable-dep-of: d2b0ca38d362 ("wifi: ath11k: fix wrong handling of CCMP256 and GCMP ciphers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75d8d7a63065b18df9555dbaab0b42d4c6f20943 ]
ACLs that reside in the algorithmic TCAM (A-TCAM) in Spectrum-2 and
newer ASICs can share the same mask if their masks only differ in up to
8 consecutive bits. For example, consider the following filters:
# tc filter add dev swp1 ingress pref 1 proto ip flower dst_ip 192.0.2.0/24 action drop
# tc filter add dev swp1 ingress pref 1 proto ip flower dst_ip 198.51.100.128/25 action drop
The second filter can use the same mask as the first (dst_ip/24) with a
delta of 1 bit.
However, the above only works because the two filters have different
values in the common unmasked part (dst_ip/24). When entries have the
same value in the common unmasked part they create undesired collisions
in the device since many entries now have the same key. This leads to
firmware errors such as [1] and to a reduced scale.
Fix by adjusting the hash table key to only include the value in the
common unmasked part. That is, without including the delta bits. That
way the driver will detect the collision during filter insertion and
spill the filter into the circuit TCAM (C-TCAM).
Add a test case that fails without the fix and adjust existing cases
that check C-TCAM spillage according to the above limitation.
[1]
mlxsw_spectrum2 0000:06:00.0: EMAD reg access failed (tid=3379b18a00003394,reg_id=3027(ptce3),type=write,status=8(resource not available))
Fixes: c22291f7cf45 ("mlxsw: spectrum: acl: Implement delta for ERP")
Reported-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d5c3ba9e4121b7738d10be3825f4d9a5a1d80ef ]
Spectrum-4 will calculate hash function for bloom filter differently from
the existing ASICs.
One of the changes is related to the way that the chunks will be build -
without padding.
As preparation for support of Spectrum-4 bloom filter, make
mlxsw_sp_acl_bf_key_encode() more flexible, so it will be able to use it
for Spectrum-4 as well.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 75d8d7a63065 ("mlxsw: spectrum_acl: Fix ACL scale regression and firmware errors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97d833ceb27dc19f8777d63f90be4a27b5daeedf ]
ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM
(A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can
contain more ACLs (i.e., tc filters), but the number of masks in each
region (i.e., tc chain) is limited.
In order to mitigate the effects of the above limitation, the device
allows filters to share a single mask if their masks only differ in up
to 8 consecutive bits. For example, dst_ip/25 can be represented using
dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the
number of masks being used (and therefore does not support mask
aggregation), but can contain a limited number of filters.
The driver uses the "objagg" library to perform the mask aggregation by
passing it objects that consist of the filter's mask and whether the
filter is to be inserted into the A-TCAM or the C-TCAM since filters in
different TCAMs cannot share a mask.
The set of created objects is dependent on the insertion order of the
filters and is not necessarily optimal. Therefore, the driver will
periodically ask the library to compute a more optimal set ("hints") by
looking at all the existing objects.
When the library asks the driver whether two objects can be aggregated
the driver only compares the provided masks and ignores the A-TCAM /
C-TCAM indication. This is the right thing to do since the goal is to
move as many filters as possible to the A-TCAM. The driver also forbids
two identical masks from being aggregated since this can only happen if
one was intentionally put in the C-TCAM to avoid a conflict in the
A-TCAM.
The above can result in the following set of hints:
H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta
H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta
After getting the hints from the library the driver will start migrating
filters from one region to another while consulting the computed hints
and instructing the device to perform a lookup in both regions during
the transition.
Assuming a filter with mask X is being migrated into the A-TCAM in the
new region, the hints lookup will return H1. Since H2 is the parent of
H1, the library will try to find the object associated with it and
create it if necessary in which case another hints lookup (recursive)
will be performed. This hints lookup for {mask Y, A-TCAM} will either
return H2 or H3 since the driver passes the library an object comparison
function that ignores the A-TCAM / C-TCAM indication.
This can eventually lead to nested objects which are not supported by
the library [1].
Fix by removing the object comparison function from both the driver and
the library as the driver was the only user. That way the lookup will
only return exact matches.
I do not have a reliable reproducer that can reproduce the issue in a
timely manner, but before the fix the issue would reproduce in several
minutes and with the fix it does not reproduce in over an hour.
Note that the current usefulness of the hints is limited because they
include the C-TCAM indication and represent aggregation that cannot
actually happen. This will be addressed in net-next.
[1]
WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0
Modules linked in:
CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42
Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0
[...]
Call Trace:
<TASK>
__objagg_obj_get+0x2bb/0x580
objagg_obj_get+0xe/0x80
mlxsw_sp_acl_erp_mask_get+0xb5/0xf0
mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270
mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510
process_one_work+0x151/0x370
Fixes: 9069a3817d82 ("lib: objagg: implement optimization hints assembly and use hints for object creation")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c636fa85feb450ca414a10010ed05361a73c93a6 ]
The band_idx variable in the function wlc_lcnphy_tx_iqlo_cal() will
never be set to 1 as BCM4313 is the only device for which the LCN PHY
code is used. This is a 2G-only device.
Fixes: 5b435de0d786 ("net: wireless: add brcm80211 drivers")
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240509231037.2014109-1-samasth.norway.ananda@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49e24c80d3c81c43e2a56101449e1eea32fcf292 ]
Initialize the completion before the mailbox channel is requested.
Fixes: 389711b37493 ("firmware: Add Turris Mox rWTM firmware driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8467cfe821ac3526f7598682ad5f90689fa8cc49 ]
The wait_for_completion_timeout() function returns 0 if timed out, and a
positive value if completed. Fix the usage of this function.
Fixes: 389711b37493 ("firmware: Add Turris Mox rWTM firmware driver")
Fixes: 2eab59cf0d20 ("firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57f20d51f35780f240ecf39d81cda23612800a92 ]
While parsing the domains list, start offsets from 0 rather than from
domains_read. The domains_read is equal to the total count of the
domains we have seen, while the domains list in the message starts from
offset 0.
Fixes: fbe639b44a82 ("soc: qcom: Introduce Protection Domain Restart helpers")
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240622-qcom-pd-mapper-v9-2-a84ee3591c8e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 107924c14e3ddd85119ca43c26a4ee1056fa9b84 ]
If the service locator server is restarted fast enough, the PDR can
rewrite locator_addr fields concurrently. Protect them by placing
modification of those fields under the main pdr->lock.
Fixes: fbe639b44a82 ("soc: qcom: Introduce Protection Domain Restart helpers")
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240622-qcom-pd-mapper-v9-1-a84ee3591c8e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e43111f52b9ec5c2d700f89a1d61c8d10dc2d9e9 ]
Dan pointed out that Smatch is concerned about this code because it uses
spin_lock_irqsave() and then calls wait_event_lock_irq() which enables
irqs before going to sleep. The comment above the function says it
should be called with interrupts enabled, but we simply hope that's true
without really confirming that. Let's add a might_sleep() here to
confirm that interrupts and preemption aren't disabled. Once we do that,
we can change the lock to be non-saving, spin_lock_irq(), to clarify
that we don't expect irqs to be disabled. If irqs are disabled by
callers they're going to be enabled anyway in the wait_event_lock_irq()
call which would be bad.
This should make Smatch happier and find bad callers faster with the
might_sleep(). We can drop the WARN_ON() in the caller because we have
the might_sleep() now, simplifying the code.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/911181ed-c430-4592-ad26-4dc948834e08@moroto.mountain
Fixes: 2bc20f3c8487 ("soc: qcom: rpmh-rsc: Sleep waiting for tcs slots to be free")
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240509184129.3924422-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ea3fd1eb9869fcdcbc9c68f9728bfc47b9503f1 ]
The critical alarm bit for the local temperature sensor (temp1) is in
bit 7 of register 0x45 (not bit 6), and the critical alarm bit for remote
temperature sensor 7 (temp8) is in bit 6 (not bit 7).
This only affects MAX6581 since all other chips supported by this driver
do not support those critical alarms.
Fixes: 5372d2d71c46 ("hwmon: Driver for Maxim MAX6697 and compatibles")
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf7467828cd4ec7ceac7a8b5b5ddb2f69f07b0e ]
Using DIV_ROUND_CLOSEST() on an unbound value can result in underflows.
Indeed, module test scripts report:
temp1_max: Suspected underflow: [min=0, read 255000, written -9223372036854775808]
temp1_crit: Suspected underflow: [min=0, read 255000, written -9223372036854775808]
Fix by introducing an extra set of clamping.
Fixes: 5372d2d71c46 ("hwmon: Driver for Maxim MAX6697 and compatibles")
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7346e7a058a2c9aa9ff1cc699c7bf18a402d9f84 ]
When the state changes from enabled to disabled, polarity, duty_cycle
and period are not configured in hardware and TIM_CCER_CCxE is just
cleared. However if the state changes from one disabled state to
another, all parameters are written to hardware because the early exit
from stm32_pwm_apply() is only taken if the pwm is currently enabled.
This yields surprises like: Applying
{ .period = 1, .duty_cycle = 0, .enabled = false }
succeeds if the pwm is initially on, but fails if it's already off
because 1 is a too small period.
Update the check for lazy disable to always exit early if the target
state is disabled, no matter what is currently configured.
Fixes: 7edf7369205b ("pwm: Add driver for STM32 plaftorm")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240703110010.672654-2-u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39b24cced70fdc336dbc0070f8b3bde61d8513a8 ]
According to the comments on fan is disabled, we change to manual mode
and set the duty cycle to 0.
For setting the duty cycle part, the register is wrong. Fix it.
Fixes: 1c301fc5394f ("hwmon: Add a driver for the ADT7475 hardware monitoring chip")
Signed-off-by: Wayne Tung <chineweff@gmail.com>
Link: https://lore.kernel.org/r/20240701073252.317397-1-chineweff@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 123b158635505c89ed0d3ef45c5845ff9030a466 ]
Commit 598afa050403 ("kbuild: warn objects shared among multiple modules")
was added to track down cases where the same object is linked into
multiple modules. This can cause serious problems if some modules are
builtin while others are not.
That test triggers this warning:
scripts/Makefile.build:236: drivers/edac/Makefile: skx_common.o is added to multiple modules: i10nm_edac skx_edac
Make this a separate module instead.
[Tony: Added more background details to commit message]
Fixes: d4dc89d069aa ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/all/20240529095132.1929397-1-arnd@kernel.org/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f4348e5a86198704368a699a7c4cdeb21d569f5 ]
Some Intel servers may configure memory in 2 levels, using
fast "near" memory (e.g. DDR) as a cache for larger, slower,
"far" memory (e.g. 3D X-point).
In these configurations the BIOS ADXL address translation for
an address in a 2-level memory range will provide details of
both the "near" and far components.
Current exported ADXL components are only for 1-level memory
system or for 2nd level memory of 2-level memory system. So
add new ADXL components for 1st level memory of 2-level memory
system to fully support 2-level memory system and the detection
of memory error source(1st level memory or 2nd level memory).
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-2-tony.luck@intel.com
Stable-dep-of: 123b15863550 ("EDAC, i10nm: make skx_common.o a separate module")
Signed-off-by: Sasha Levin <sashal@kernel.org>
* Gotta store the pointer of the only ZRAM device for compaction
* Also, more than one ZRAM device is useless
Signed-off-by: Adithya R <gh0strider.2k18.reborn@gmail.com>
Make the menu governor check the tick_nohz_get_next_hrtimer()
return value so as to avoid dealing with negative "sleep length"
values and make it use that value directly when the tick is stopped.
While at it, rename local variable delta_next in menu_select() to
delta_tick which better reflects its purpose.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The effective affinity mask causes a lot of bugs by virtue of many
set_irq_affinity handlers only setting an effective affinity mask for an
IRQ's parent but not the IRQ itself. Since this is a widespread issue that
would require manual fixing on every different SoC, just disable the
effective affinity mask altogether and use the first CPU in an affinity
mask configured.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
Now that we have a simple task exit notifier system to notify
uid_sys_stats when tasks exit independently of the profiling subsystem,
remove this unnecessary dependency.
Test: /proc/uid_cputime shows valid stats with profiling disabled
Signed-off-by: Danny Lin <danny@kdrag0n.dev>
kmemleak_ignore() shouldn't be used on the gen_pool allocations since they
aren't slab allocations. This leads to a flurry of warnings from kmemleak;
fix it by using kmemleak_ignore() correctly.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
A lot of CPU time is wasted on allocating, populating, and copying
debug names back and forth with userspace when they're not actually
needed. We can't just remove the name buffers from the various sync data
structures though because we must preserve ABI compatibility with
userspace, but instead we can just pretend the name fields of the
user-shared structs aren't there. This massively reduces the sizes of
memory allocated for these data structures and the amount of data passed
between userspace, as well as eliminates a kzalloc() entirely from
sync_file_ioctl_fence_info(), thus improving graphics performance.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
the previous definitions as well as the creation of this is locked behind CONFIG_ZRAM_LRU_WRITEBACK as well
Change-Id: I869b5595f69cc481e93ca6862b460594762d9b25
Signed-off-by: Ruchit <risenid@duck.com>
This saves one memory allocation, and ensures the bvecs aren't freed
before the AIO completion. This will allow the lower level code to be
optimized so that it can avoid allocating another bvec array.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
(cherry picked from commit ecd7fba0ade1d6d8d49d320df9caf96922a376b2)
(cherry picked from commit 272d2ea22b0e3da786a506896e36d3a586e6c252)
(cherry picked from commit 83ff0aa1cc08c329feb0748c575810b3ce8c0077)
(cherry picked from commit d0dc27fcc3f57d556ce4468a060e54f25c7b91b0)
(cherry picked from commit 847a30a99fc4b11c9e6cf2ec049ca20a6da9c769)
(cherry picked from commit 3799ad215edeb9276c4d16150a33de916cfa4ea1)
(cherry picked from commit ee8f417b3276049e4f0bbadf4c4524f071de2361)
commit ed7f2afdd0e043a397677e597ced0830b83ba0b3 upstream.
The cited commit missed to check against the validity of the frame length
in the tap_get_user_xdp() path, which could cause a corrupted skb to be
sent downstack. Even before the skb is transmitted, the
tap_get_user_xdp()-->skb_set_network_header() may assume the size is more
than ETH_HLEN. Once transmitted, this could either cause out-of-bound
access beyond the actual length, or confuse the underlayer with incorrect
or inconsistent header length in the skb metadata.
In the alternative path, tap_get_user() already prohibits short frame which
has the length less than Ethernet header size from being transmitted.
This is to drop any frame shorter than the Ethernet header size just like
how tap_get_user() does.
CVE: CVE-2024-41090
Link: https://lore.kernel.org/netdev/1717026141-25716-1-git-send-email-si-wei.liu@oracle.com/
Fixes: 0efac27791ee ("tap: accept an array of XDP buffs through sendmsg()")
Cc: stable@vger.kernel.org
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20240724170452.16837-2-dongli.zhang@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 049584807f1d797fc3078b68035450a9769eb5c3 upstream.
The cited commit missed to check against the validity of the frame length
in the tun_xdp_one() path, which could cause a corrupted skb to be sent
downstack. Even before the skb is transmitted, the
tun_xdp_one-->eth_type_trans() may access the Ethernet header although it
can be less than ETH_HLEN. Once transmitted, this could either cause
out-of-bound access beyond the actual length, or confuse the underlayer
with incorrect or inconsistent header length in the skb metadata.
In the alternative path, tun_get_user() already prohibits short frame which
has the length less than Ethernet header size from being transmitted for
IFF_TAP.
This is to drop any frame shorter than the Ethernet header size just like
how tun_get_user() does.
CVE: CVE-2024-41091
Inspired-by: https://lore.kernel.org/netdev/1717026141-25716-1-git-send-email-si-wei.liu@oracle.com/
Fixes: 043d222f93ab ("tuntap: accept an array of XDP buffs through sendmsg()")
Cc: stable@vger.kernel.org
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20240724170452.16837-3-dongli.zhang@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6769a23697f17f9bf9365ca8ed62fe37e361a05a upstream.
The "instance" variable needs to be signed for the error handling to work.
Fixes: 8b2faf1a4f3b ("drm/amdgpu: add error handle to avoid out-of-bounds")
Reviewed-by: Bob Zhou <bob.zhou@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Siddh Raman Pant <siddh.raman.pant@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fe4ce5836e932f5766317cb651c1ff2a4cd0506 upstream.
There are two .exit_cmd_priv implementations. Both implementations use
resources associated with the SCSI host. Make sure that these resources are
still available when .exit_cmd_priv is called by waiting inside
scsi_remove_host() until the tag set has been freed.
This commit fixes the following use-after-free:
==================================================================
BUG: KASAN: use-after-free in srp_exit_cmd_priv+0x27/0xd0 [ib_srp]
Read of size 8 at addr ffff888100337000 by task multipathd/16727
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_report.cold+0x5e/0x5db
kasan_report+0xab/0x120
srp_exit_cmd_priv+0x27/0xd0 [ib_srp]
scsi_mq_exit_request+0x4d/0x70
blk_mq_free_rqs+0x143/0x410
__blk_mq_free_map_and_rqs+0x6e/0x100
blk_mq_free_tag_set+0x2b/0x160
scsi_host_dev_release+0xf3/0x1a0
device_release+0x54/0xe0
kobject_put+0xa5/0x120
device_release+0x54/0xe0
kobject_put+0xa5/0x120
scsi_device_dev_release_usercontext+0x4c1/0x4e0
execute_in_process_context+0x23/0x90
device_release+0x54/0xe0
kobject_put+0xa5/0x120
scsi_disk_release+0x3f/0x50
device_release+0x54/0xe0
kobject_put+0xa5/0x120
disk_release+0x17f/0x1b0
device_release+0x54/0xe0
kobject_put+0xa5/0x120
dm_put_table_device+0xa3/0x160 [dm_mod]
dm_put_device+0xd0/0x140 [dm_mod]
free_priority_group+0xd8/0x110 [dm_multipath]
free_multipath+0x94/0xe0 [dm_multipath]
dm_table_destroy+0xa2/0x1e0 [dm_mod]
__dm_destroy+0x196/0x350 [dm_mod]
dev_remove+0x10c/0x160 [dm_mod]
ctl_ioctl+0x2c2/0x590 [dm_mod]
dm_ctl_ioctl+0x5/0x10 [dm_mod]
__x64_sys_ioctl+0xb4/0xf0
dm_ctl_ioctl+0x5/0x10 [dm_mod]
__x64_sys_ioctl+0xb4/0xf0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Link: https://lore.kernel.org/r/20220826002635.919423-1-bvanassche@acm.org
Fixes: 65ca846a5314 ("scsi: core: Introduce {init,exit}_cmd_priv()")
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: Li Zhijian <lizhijian@fujitsu.com>
Reported-by: Li Zhijian <lizhijian@fujitsu.com>
Tested-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[mheyne: fixed contextual conflicts:
- drivers/scsi/hosts.c: due to missing commit 973dac8a8a14 ("scsi: core: Refine how we set tag_set NUMA node")
- drivers/scsi/scsi_sysfs.c: due to missing commit 6f8191fdf41d ("block: simplify disk shutdown")
- drivers/scsi/scsi_scan.c: due to missing commit 59506abe5e34 ("scsi: core: Inline scsi_mq_alloc_queue()")]
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 233323f9b9f828cd7cd5145ad811c1990b692542 upstream.
The acpi_cst_latency_cmp() comparison function currently used for
sorting C-state latencies does not satisfy transitivity, causing
incorrect sorting results.
Specifically, if there are two valid acpi_processor_cx elements A and B
and one invalid element C, it may occur that A < B, A = C, and B = C.
Sorting algorithms assume that if A < B and A = C, then C < B, leading
to incorrect ordering.
Given the small size of the array (<=8), we replace the library sort
function with a simple insertion sort that properly ignores invalid
elements and sorts valid ones based on latency. This change ensures
correct ordering of the C-state latencies.
Fixes: 65ea8f2c6e23 ("ACPI: processor idle: Fix up C-state latency if not ordered")
Reported-by: Julian Sikorski <belegdol@gmail.com>
Closes: https://lore.kernel.org/lkml/70674dc7-5586-4183-8953-8095567e73df@gmail.com
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Link: https://patch.msgid.link/20240701205639.117194-1-visitorckw@gmail.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c8bd922d924bb4ab6c6c488310157d1a27996f31 ]
Like other SPI controller flags, bits_per_word_mask may be used by a
peripheral driver, so it needs to reflect the capabilities of the
underlying controller.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240708-spi-mux-fix-v1-3-6c8845193128@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce1dac560a74220f2e53845ec0723b562288aed4 ]
While in commit 2dd33f9cec90 ("spi: imx: support DMA for imx35") it was
claimed that DMA works on i.MX25, i.MX31 and i.MX35 the respective
device trees don't add DMA channels. The Reference manuals of i.MX31 and
i.MX25 also don't mention the CSPI core being DMA capable. (I didn't
check the others.)
Since commit e267a5b3ec59 ("spi: spi-imx: Use dev_err_probe for failed
DMA channel requests") this results in an error message
spi_imx 43fa4000.spi: error -ENODEV: can't get the TX DMA channel!
during boot. However that isn't fatal and the driver gets loaded just
fine, just without using DMA.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://patch.msgid.link/20240508095610.2146640-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab2068a6fb84751836a84c26ca72b3beb349619d ]
The expander phy will be treated as broadcast flutter in the next
revalidation after the exp-attached end device probe failed, as follows:
[78779.654026] sas: broadcast received: 0
[78779.654037] sas: REVALIDATING DOMAIN on port 0, pid:10
[78779.654680] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78779.662977] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78779.662986] sas: ex 500e004aaaaaaa1f phy05 new device attached
[78779.663079] sas: ex 500e004aaaaaaa1f phy05:U:8 attached: 500e004aaaaaaa05 (stp)
[78779.693542] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] found
[78779.701155] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[78779.707864] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
...
[78835.161307] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[78835.171344] sas: sas_probe_sata: for exp-attached device 500e004aaaaaaa05 returned -19
[78835.180879] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] is gone
[78835.187487] sas: broadcast received: 0
[78835.187504] sas: REVALIDATING DOMAIN on port 0, pid:10
[78835.188263] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78835.195870] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78835.195875] sas: ex 500e004aaaaaaa1f rediscovering phy05
[78835.196022] sas: ex 500e004aaaaaaa1f phy05:U:A attached: 500e004aaaaaaa05 (stp)
[78835.196026] sas: ex 500e004aaaaaaa1f phy05 broadcast flutter
[78835.197615] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
The cause of the problem is that the related ex_phy's attached_sas_addr was
not cleared after the end device probe failed, so reset it.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240619091742.25465-1-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d34d8163fd87978a6abd792e2d8ad849f4c3d57 ]
As the potential failure of usb_submit_urb(), it should be better to
return the err variable to catch the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/all/20240521041020.1519416-1-nichen@iscas.ac.cn
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 955af6355ddfe35140f9706a635838212a32513b ]
See the added comment for details. Also fix a typo in the
quirk's define.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Link: https://lore.kernel.org/r/20240531190100.3874731-1-tjakobi@math.uni-bielefeld.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a69ce592cbe0417664bc5a075205aa75c2ec1273 ]
The Lenovo N24 on resume becomes stuck in a state where it
sends incorrect packets, causing elantech_packet_check_v4 to fail.
The only way for the device to resume sending the correct packets is for
it to be disabled and then re-enabled.
This change adds a dmi check to trigger this behavior on resume.
Signed-off-by: Jonathan Denose <jdenose@google.com>
Link: https://lore.kernel.org/r/20240503155020.v2.1.Ifa0e25ebf968d8f307f58d678036944141ab17e6@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1db5322b7e6b58e1b304ce69a50e9dca798ca95b ]
Change level for the "not connected" client message in the write
callback from error to debug.
The MEI driver currently disconnects all clients upon system suspend.
This behavior is by design and user-space applications with
open connections before the suspend are expected to handle errors upon
resume, by reopening their handles, reconnecting,
and retrying their operations.
However, the current driver implementation logs an error message every
time a write operation is attempted on a disconnected client.
Since this is a normal and expected flow after system resume
logging this as an error can be misleading.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240530091415.725247-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c462ecd659b5fce731f1d592285832fd6ad54053 ]
Block size should be between 512 and PAGE_SIZE and be a power of 2. The current
check does not validate this, so update the check.
Without this patch, null_blk would Oops due to a null pointer deref when
loaded with bs=1536 [1].
Link: https://lore.kernel.org/all/87wmn8mocd.fsf@metaspace.dk/
Signed-off-by: Andreas Hindborg <a.hindborg@samsung.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240603192645.977968-1-nmi@metaspace.dk
[axboe: remove unnecessary braces and != 0 check]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
