[ Upstream commit 6d710b769c1f5f0d55c9ad9bb49b7dce009ec103 ]
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ef79cd1412236d884ab0c46b4d1921380807b48 ]
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78d60dae9a0c9f09aa3d6477c94047df2fe6f7b0 ]
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Fixes: cb1a60923609 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad90d0358bd3b4554f243a425168fc7cebe7d04e ]
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow. So all resources that were not freed
are leaked in this case. Skipping serial8250_unregister_port() has the
potential to keep enough of the UART around to trigger a use-after-free.
So replace the error return (and with it the little helpful error
message) by a more useful error message and continue to cleanup.
Fixes: e3f0c638f428 ("serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231110152927.70601-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7c45eaa813476bd195ac1227a64b52f9cf2e2030 upstream.
There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986e6 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.
Fixes: 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e42c301ce64e0dcca547626eb486877d502d336 upstream.
Currently there is no support for earlycon on the AM654 UART
controller. This commit adds it.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031131242.15516-1-rwahl@gmx.de
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6bb057418876cdfdd29a6f7b8cef54539ee8811 upstream.
Starting RX DMA on THRI interrupt is too early because TX may not have
finished yet.
This change is inspired by commit 90b8596ac460 ("serial: 8250: Prevent
starting up DMA Rx on THRI interrupt") and fixes DMA issues I had with
an AM62 SoC that is using the 8250 OMAP variant.
Cc: stable@vger.kernel.org
Fixes: c26389f998a8 ("serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231101171431.16495-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8973ab7a2441b286218f4a5c4c33680e2f139996 upstream.
This fixes commit 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX
interrupt after DMA enable") which unfortunately set the
UART_HAS_RHR_IT_DIS bit in the UART_OMAP_IER2 register and never
cleared it.
Cc: stable@vger.kernel.org
Fixes: 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20231031110909.11695-1-rwahl@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08ce9a1b72e38cf44c300a44ac5858533eb3c860 upstream.
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58ac1b3799799069d53f5bf95c093f2fe8dd3cc5 upstream.
Since there is no guarantee that the memory returned by
dma_alloc_coherent() is associated with a 'struct page', using the
architecture specific phys_to_page() is wrong, but using
virt_to_page() would be as well.
Stop using sg lists altogether and just use the *_single() functions
instead. This also simplifies the code a bit since the scatterlists in
this driver always have only one entry anyway.
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
gc: Add a commit log from the initial thread:
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
Fixes: cb06ff102e2d7 ("ARM: PL011: Add support for Rx DMA buffer polling.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231122171503.235649-1-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b68061983471470d4109bac776145245f06bc09 ]
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2a1d728f20ed ("tty: serial: meson: fix hard LOCKUP on crtscts mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27d44e05d7b85d9d4cfe0a3c0663ea49752ece93 ]
Now the DT bindings has a property to get the FIFO size for a particular port,
retrieve it and use to setup the FIFO interrupts threshold.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210518075833.3736038-3-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2a1d728f20ed ("tty: serial: meson: fix hard LOCKUP on crtscts mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 021212f5335229ed12e3d31f9b7d30bd3bb66f7d ]
The variable id being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed. Since id is just being used in a for-loop
inside a local scope, move the declaration of id to that scope.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210426101106.9122-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2a1d728f20ed ("tty: serial: meson: fix hard LOCKUP on crtscts mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 33092fb3af51deb80849e90a17bada44bbcde6b3 upstream.
The UC-257 is a serial + LPT card, so remove it from this driver.
A patch has been submitted to add it to parport_serial instead.
Additionaly, the UC-431 does not use this card ID, only the UC-420
does. The 431 is a 3-port card and there is no generic 3-port configuration
available, so remove reference to it from this driver.
Fixes: 152d1afa834c ("tty: Add support for Brainboxes UC cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB78995ADF7394C74AD4CF3357C4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 560706eff7c8e5621b0d63afe0866e0e1906e87e ]
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a62618d ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91bb
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a62618d ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 398cecc24846e867b9f90a0bd22730e3df6b05be ]
We must idle the uart only after serial8250_unregister_port(). Otherwise
unbinding the uart via sysfs while doing cat on the port produces an
imprecise external abort:
mem_serial_in from omap_8250_pm+0x44/0xf4
omap_8250_pm from uart_hangup+0xe0/0x194
uart_hangup from __tty_hangup.part.0+0x37c/0x3a8
__tty_hangup.part.0 from uart_remove_one_port+0x9c/0x22c
uart_remove_one_port from serial8250_unregister_port+0x60/0xe8
serial8250_unregister_port from omap8250_remove+0x6c/0xd0
omap8250_remove from platform_remove+0x28/0x54
Turns out the driver needs to have runtime PM functional before the
driver probe calls serial8250_register_8250_port(). And it needs
runtime PM after driver remove calls serial8250_unregister_port().
On probe, we need to read registers before registering the port in
omap_serial_fill_features_erratas(). We do that with custom uart_read()
already.
On remove, after serial8250_unregister_port(), we need to write to the
uart registers to idle the device. Let's add a custom uart_write() for
that.
Currently the uart register access depends on port->membase to be
initialized, which won't work after serial8250_unregister_port().
Let's use priv->membase instead, and use it for runtime PM related
functions to remove the dependency to port->membase for early and
late register access.
Note that during use, we need to check for a valid port in the runtime PM
related functions. This is needed for the optional wakeup configuration.
We now need to set the drvdata a bit earlier so it's available for the
runtime PM functions.
With the port checks in runtime PM functions, the old checks for priv in
omap8250_runtime_suspend() and omap8250_runtime_resume() functions are no
longer needed and are removed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 560706eff7c8 ("serial: 8250_omap: Fix errors with no_console_suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
