[ Upstream commit c0a2a1b0d631fc460d830f52d06211838874d655 ]
ppp_sync_ioctl allows setting device MRU, but does not sanity check
this input.
Limit to a sane upper bound of 64KB.
No implementation I could find generates larger than 64KB frames.
RFC 2823 mentions an upper bound of PPP over SDL of 64KB based on the
16-bit length field. Other protocols will be smaller, such as PPPoE
(9KB jumbo frame) and PPPoA (18190 maximum CPCS-SDU size, RFC 2364).
PPTP and L2TP encapsulate in IP.
Syzbot managed to trigger alloc warning in __alloc_pages:
if (WARN_ON_ONCE_GFP(order > MAX_ORDER, gfp))
WARNING: CPU: 1 PID: 37 at mm/page_alloc.c:4544 __alloc_pages+0x3ab/0x4a0 mm/page_alloc.c:4544
__alloc_skb+0x12b/0x330 net/core/skbuff.c:651
__netdev_alloc_skb+0x72/0x3f0 net/core/skbuff.c:715
netdev_alloc_skb include/linux/skbuff.h:3225 [inline]
dev_alloc_skb include/linux/skbuff.h:3238 [inline]
ppp_sync_input drivers/net/ppp/ppp_synctty.c:669 [inline]
ppp_sync_receive+0xff/0x680 drivers/net/ppp/ppp_synctty.c:334
tty_ldisc_receive_buf+0x14c/0x180 drivers/tty/tty_buffer.c:390
tty_port_default_receive_buf+0x70/0xb0 drivers/tty/tty_port.c:37
receive_buf drivers/tty/tty_buffer.c:444 [inline]
flush_to_ldisc+0x261/0x780 drivers/tty/tty_buffer.c:494
process_one_work+0x884/0x15c0 kernel/workqueue.c:2630
With call
ioctl$PPPIOCSMRU1(r1, 0x40047452, &(0x7f0000000100)=0x5e6417a8)
Similar code exists in other drivers that implement ppp_channel_ops
ioctl PPPIOCSMRU. Those might also be in scope. Notably excluded from
this are pppol2tp_ioctl and pppoe_ioctl.
This code goes back to the start of git history.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+6177e1f90d92583bcc58@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65e98bb56fa3ce2edb400930c05238c9b380500e ]
Currently the reset process in hns3 and firmware watchdog init process is
asynchronous. We think firmware watchdog initialization is completed
before VF clear the interrupt source. However, firmware initialization
may not complete early. So VF will receive multiple reset interrupts
and fail to reset.
So we add delay before VF interrupt source and 5 ms delay
is enough to avoid second reset interrupt.
Fixes: 427900d27d86 ("net: hns3: fix the timing issue of VF clearing interrupt sources")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbd2f3b20c6ae425665b6975d766e3653d453e73 ]
When a VF is calling hns3_init_mac_addr(), get_mac_addr() may
return fail, then the value of mac_addr_temp is not initialized.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 719639853d88071dfdfd8d9971eca9c283ff314c ]
KMSAN reported the following uninit-value access issue:
=====================================================
BUG: KMSAN: uninit-value in ppp_sync_input drivers/net/ppp/ppp_synctty.c:690 [inline]
BUG: KMSAN: uninit-value in ppp_sync_receive+0xdc9/0xe70 drivers/net/ppp/ppp_synctty.c:334
ppp_sync_input drivers/net/ppp/ppp_synctty.c:690 [inline]
ppp_sync_receive+0xdc9/0xe70 drivers/net/ppp/ppp_synctty.c:334
tiocsti+0x328/0x450 drivers/tty/tty_io.c:2295
tty_ioctl+0x808/0x1920 drivers/tty/tty_io.c:2694
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0x211/0x400 fs/ioctl.c:857
__x64_sys_ioctl+0x97/0xe0 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Uninit was created at:
__alloc_pages+0x75d/0xe80 mm/page_alloc.c:4591
__alloc_pages_node include/linux/gfp.h:238 [inline]
alloc_pages_node include/linux/gfp.h:261 [inline]
__page_frag_cache_refill+0x9a/0x2c0 mm/page_alloc.c:4691
page_frag_alloc_align+0x91/0x5d0 mm/page_alloc.c:4722
page_frag_alloc include/linux/gfp.h:322 [inline]
__netdev_alloc_skb+0x215/0x6d0 net/core/skbuff.c:728
netdev_alloc_skb include/linux/skbuff.h:3225 [inline]
dev_alloc_skb include/linux/skbuff.h:3238 [inline]
ppp_sync_input drivers/net/ppp/ppp_synctty.c:669 [inline]
ppp_sync_receive+0x237/0xe70 drivers/net/ppp/ppp_synctty.c:334
tiocsti+0x328/0x450 drivers/tty/tty_io.c:2295
tty_ioctl+0x808/0x1920 drivers/tty/tty_io.c:2694
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0x211/0x400 fs/ioctl.c:857
__x64_sys_ioctl+0x97/0xe0 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
CPU: 0 PID: 12950 Comm: syz-executor.1 Not tainted 6.6.0-14500-g1c41041124bd #10
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc38 04/01/2014
=====================================================
ppp_sync_input() checks the first 2 bytes of the data are PPP_ALLSTATIONS
and PPP_UI. However, if the data length is 1 and the first byte is
PPP_ALLSTATIONS, an access to an uninitialized value occurs when checking
PPP_UI. This patch resolves this issue by checking the data length.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 499d02790495958506a64f37ceda7e97345a50a8 ]
Currently we are setting the rate in the tx cmd for
mgmt frames (e.g. during connection establishment).
This was problematic when sending mgmt frames in eSR mode,
as we don't know what link this frame will be sent on
(This is decided by the FW), so we don't know what is the
lowest rate.
Fix this by not setting the rate in tx cmd and rely
on FW to choose the right one.
Set rate only for injected frames with fixed rate,
or when no sta is given.
Also set for important frames (EAPOL etc.) the High Priority flag.
Fixes: 055b22e770dd ("iwlwifi: mvm: Set Tx rate and flags when there is not station")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230913145231.6c7e59620ee0.I6eaed3ccdd6dd62b9e664facc484081fc5275843@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 170c75d43a77dc937c58f07ecf847ba1b42ab74e ]
As talked about in commit d66d24ac300c ("ath10k: Keep track of which
interrupts fired, don't poll them"), if we access the copy engine
register at a bad time then ath10k can go boom. However, it's not
necessarily easy to know when it's safe to access them.
The ChromeOS test labs saw a crash that looked like this at
shutdown/reboot time (on a chromeos-5.15 kernel, but likely the
problem could also reproduce upstream):
Internal error: synchronous external abort: 96000010 [#1] PREEMPT SMP
...
CPU: 4 PID: 6168 Comm: reboot Not tainted 5.15.111-lockdep-19350-g1d624fe6758f #1 010b9b233ab055c27c6dc88efb0be2f4e9e86f51
Hardware name: Google Kingoftown (DT)
...
pc : ath10k_snoc_read32+0x50/0x74 [ath10k_snoc]
lr : ath10k_snoc_read32+0x24/0x74 [ath10k_snoc]
...
Call trace:
ath10k_snoc_read32+0x50/0x74 [ath10k_snoc ...]
ath10k_ce_disable_interrupt+0x190/0x65c [ath10k_core ...]
ath10k_ce_disable_interrupts+0x8c/0x120 [ath10k_core ...]
ath10k_snoc_hif_stop+0x78/0x660 [ath10k_snoc ...]
ath10k_core_stop+0x13c/0x1ec [ath10k_core ...]
ath10k_halt+0x398/0x5b0 [ath10k_core ...]
ath10k_stop+0xfc/0x1a8 [ath10k_core ...]
drv_stop+0x148/0x6b4 [mac80211 ...]
ieee80211_stop_device+0x70/0x80 [mac80211 ...]
ieee80211_do_stop+0x10d8/0x15b0 [mac80211 ...]
ieee80211_stop+0x144/0x1a0 [mac80211 ...]
__dev_close_many+0x1e8/0x2c0
dev_close_many+0x198/0x33c
dev_close+0x140/0x210
cfg80211_shutdown_all_interfaces+0xc8/0x1e0 [cfg80211 ...]
ieee80211_remove_interfaces+0x118/0x5c4 [mac80211 ...]
ieee80211_unregister_hw+0x64/0x1f4 [mac80211 ...]
ath10k_mac_unregister+0x4c/0xf0 [ath10k_core ...]
ath10k_core_unregister+0x80/0xb0 [ath10k_core ...]
ath10k_snoc_free_resources+0xb8/0x1ec [ath10k_snoc ...]
ath10k_snoc_shutdown+0x98/0xd0 [ath10k_snoc ...]
platform_shutdown+0x7c/0xa0
device_shutdown+0x3e0/0x58c
kernel_restart_prepare+0x68/0xa0
kernel_restart+0x28/0x7c
Though there's no known way to reproduce the problem, it makes sense
that it would be the same issue where we're trying to access copy
engine registers when it's not allowed.
Let's fix this by changing how we "disable" the interrupts. Instead of
tweaking the copy engine registers we'll just use disable_irq() and
enable_irq(). Then we'll configure the interrupts once at power up
time.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230630151842.1.If764ede23c4e09a43a842771c2ddf99608f25f8e@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb4c132ebfeac5962f7258ffc831caa0c4dada1a ]
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/ath/ath10k/debug.c:8:
In file included from ./include/linux/module.h:13:
In file included from ./include/linux/stat.h:19:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'ath10k_debug_get_et_strings()' where
fortification logic inteprets call to 'memcpy()' as an attempt to copy
the whole 'ath10k_gstrings_stats' array from it's first member and so
issues an overread warning. This warning may be silenced by passing
an address of the whole array and not the first member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230829093652.234537-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95f97fe0ac974467ab4da215985a32b2fdf48af0 ]
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/ath/ath9k/debug.c:17:
In file included from ./include/linux/slab.h:16:
In file included from ./include/linux/gfp.h:7:
In file included from ./include/linux/mmzone.h:8:
In file included from ./include/linux/spinlock.h:56:
In file included from ./include/linux/preempt.h:79:
In file included from ./arch/x86/include/asm/preempt.h:9:
In file included from ./include/linux/thread_info.h:60:
In file included from ./arch/x86/include/asm/thread_info.h:53:
In file included from ./arch/x86/include/asm/cpufeature.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
In file included from drivers/net/wireless/ath/ath9k/htc_drv_debug.c:17:
In file included from drivers/net/wireless/ath/ath9k/htc.h:20:
In file included from ./include/linux/module.h:13:
In file included from ./include/linux/stat.h:19:
In file included from ./include/linux/time.h:60:
In file included from ./include/linux/time32.h:13:
In file included from ./include/linux/timex.h:67:
In file included from ./arch/x86/include/asm/timex.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'ath9k_get_et_strings()' and
'ath9k_htc_get_et_strings()' due to the same reason: fortification logic
inteprets call to 'memcpy()' as an attempt to copy the whole array from
it's first member and so issues an overread warning. These warnings may
be silenced by passing an address of the whole array and not the first
member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230829093856.234584-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbaccdc42483c65016f1bae89128c08dc17cfb2a ]
When compiling with clang 16.0.6 and CONFIG_FORTIFY_SOURCE=y, I've
noticed the following (somewhat confusing due to absence of an actual
source code location):
In file included from drivers/net/wireless/virtual/mac80211_hwsim.c:18:
In file included from ./include/linux/slab.h:16:
In file included from ./include/linux/gfp.h:7:
In file included from ./include/linux/mmzone.h:8:
In file included from ./include/linux/spinlock.h:56:
In file included from ./include/linux/preempt.h:79:
In file included from ./arch/x86/include/asm/preempt.h:9:
In file included from ./include/linux/thread_info.h:60:
In file included from ./arch/x86/include/asm/thread_info.h:53:
In file included from ./arch/x86/include/asm/cpufeature.h:5:
In file included from ./arch/x86/include/asm/processor.h:23:
In file included from ./arch/x86/include/asm/msr.h:11:
In file included from ./arch/x86/include/asm/cpumask.h:5:
In file included from ./include/linux/cpumask.h:12:
In file included from ./include/linux/bitmap.h:11:
In file included from ./include/linux/string.h:254:
./include/linux/fortify-string.h:592:4: warning: call to '__read_overflow2_field'
declared with 'warning' attribute: detected read beyond size of field (2nd
parameter); maybe use struct_group()? [-Wattribute-warning]
__read_overflow2_field(q_size_field, size);
The compiler actually complains on 'mac80211_hwsim_get_et_strings()' where
fortification logic inteprets call to 'memcpy()' as an attempt to copy the
whole 'mac80211_hwsim_gstrings_stats' array from its first member and so
issues an overread warning. This warning may be silenced by passing
an address of the whole array and not the first member to 'memcpy()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://lore.kernel.org/r/20230829094140.234636-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8999ce4cfc87e61b4143ec2e7b93d8e92e11fa7f ]
So far we ignore the setting of IFF_MULTICAST. Fix this and clear bit
AcceptMulticast if IFF_MULTICAST isn't set.
Note: Based on the implementations I've seen it doesn't seem to be 100% clear
what a driver is supposed to do if IFF_ALLMULTI is set but IFF_MULTICAST
is not. This patch is based on the understanding that IFF_MULTICAST has
precedence.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/4a57ba02-d52d-4369-9f14-3565e6c1f7dc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db456d90a4c1b43b6251fa4348c8adc59b583274 ]
From XGMAC Core 3.20 and later, each Flexible PPS has individual PPSEN bit
to select Fixed mode or Flexible mode. The PPSEN must be set, or it stays
in Fixed PPS mode by default.
XGMAC Core prior 3.20, only PPSEN0(bit 4) is writable. PPSEN{1,2,3} are
read-only reserved, and they are already in Flexible mode by default, our
new code always set PPSEN{1,2,3} do not make things worse ;-)
Fixes: 95eaf3cd0a90 ("net: stmmac: dwxgmac: Add Flexible PPS support")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa5f1311c4998e9e6317c52bc5ee93b3a0f36df ]
RTL8168H and RTL8107E ethernet adapters erroneously filter unicast
eapol packets unless allmulti is enabled. These devices correspond to
RTL_GIGA_MAC_VER_46 and VER_48. Add an exception for VER_46 and VER_48
in the same way that VER_35 has an exception.
Fixes: 6e1d0b898818 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: Patrick Thompson <ptf@google.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20231030205031.177855-1-ptf@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff672b9ffeb3f82135488ac16c5c5eb4b992999b ]
Both ipvlan_process_v4_outbound() and ipvlan_process_v6_outbound()
increment dev->stats.tx_errors in case of errors.
Unfortunately there are two issues :
1) ipvlan_get_stats64() does not propagate dev->stats.tx_errors to user.
2) Increments are not atomic. KCSAN would complain eventually.
Use DEV_STATS_INC() to not miss an update, and change ipvlan_get_stats64()
to copy the value back to user.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Link: https://lore.kernel.org/r/20231026131446.3933175-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225d9ddbacb102621af6d28ff7bf5a0b4ce249d8 ]
tp->rcv_tstamp should be set to tcp_jiffies, not tcp_time_stamp().
Fixes: cc35c88ae4db ("crypto : chtls - CPL handler definition")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621735f590643e3048ca2060c285b80551660601 ]
In very rare cases (I've seen two reports so far about different
RTL8125 chip versions) it seems the MAC locks up when link goes down
and requires a software reset to get revived.
Realtek doesn't publish hw errata information, therefore the root cause
is unknown. Realtek vendor drivers do a full hw re-initialization on
each link-up event, the slimmed-down variant here was reported to fix
the issue for the reporting user.
It's not fully clear which parts of the NIC are reset as part of the
software reset, therefore I can't rule out side effects.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Reported-by: Martin Kjær Jørgensen <me@lagy.org>
Link: https://lore.kernel.org/netdev/97ec2232-3257-316c-c3e7-a08192ce16a6@gmail.com/T/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/9edde757-9c3b-4730-be3b-0ef3a374ff71@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b6c6065fca123d419afef005a696f51e6590470 ]
The open code is defined as a helper function(tp_to_dev) on r8169_main.c,
which the open code is &tp->pci_dev->dev. The helper function was added
in commit 1e1205b7d3e9 ("r8169: add helper tp_to_dev"). And then later,
commit f1e911d5d0df ("r8169: add basic phylib support") added
r8169_phylink_handler function but it didn't use the helper function.
Thus, tp_to_dev() replaces the open code. This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20221129161244.5356-1-claudiajkang@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 621735f59064 ("r8169: fix rare issue with broken rx after link-down on RTL8125")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6841cab8c4504835e4011689cbdb3351dec693fd ]
This race condition was discovered while updating the at91_can driver
to use can_bus_off(). The following scenario describes how the
converted at91_can driver would behave.
When a CAN device goes into BUS-OFF state, the driver usually
stops/resets the CAN device and calls can_bus_off().
This function sets the netif carrier to off, and (if configured by
user space) schedules a delayed work that calls can_restart() to
restart the CAN device.
The can_restart() function first checks if the carrier is off and
triggers an error message if the carrier is OK.
Then it calls the driver's do_set_mode() function to restart the
device, then it sets the netif carrier to on. There is a race window
between these two calls.
The at91 CAN controller (observed on the sama5d3, a single core 32 bit
ARM CPU) has a hardware limitation. If the device goes into bus-off
while sending a CAN frame, there is no way to abort the sending of
this frame. After the controller is enabled again, another attempt is
made to send it.
If the bus is still faulty, the device immediately goes back to the
bus-off state. The driver calls can_bus_off(), the netif carrier is
switched off and another can_restart is scheduled. This occurs within
the race window before the original can_restart() handler marks the
netif carrier as OK. This would cause the 2nd can_restart() to be
called with an OK netif carrier, resulting in an error message.
The flow of the 1st can_restart() looks like this:
can_restart()
// bail out if netif_carrier is OK
netif_carrier_ok(dev)
priv->do_set_mode(dev, CAN_MODE_START)
// enable CAN controller
// sama5d3 restarts sending old message
// CAN devices goes into BUS_OFF, triggers IRQ
// IRQ handler start
at91_irq()
at91_irq_err_line()
can_bus_off()
netif_carrier_off()
schedule_delayed_work()
// IRQ handler end
netif_carrier_on()
The 2nd can_restart() will be called with an OK netif carrier and the
error message will be printed.
To close the race window, first set the netif carrier to on, then
restart the controller. In case the restart fails with an error code,
roll back the netif carrier to off.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-2-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe5c9940dfd8ba0c73672dddb30acd1b7a11d4c7 ]
During testing, I triggered a can_restart() with the netif carrier
being OK [1]. The BUG_ON, which checks if the carrier is OK, results
in a fatal kernel crash. This is neither helpful for debugging nor for
a production system.
[1] The root cause is a race condition in can_restart() which will be
fixed in the next patch.
Do not crash the kernel, issue an error message instead, and continue
restarting the CAN device anyway.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-1-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3391ee7f9ea508c375d443cd712c2e699be235b4 ]
In 'rtl92c_dm_check_edca_turbo()', 'rtl88e_dm_check_edca_turbo()',
and 'rtl8723e_dm_check_edca_turbo()', the DL limit should be set
from the corresponding field of 'rtlpriv->btcoexist' rather than
UL. Compile tested only.
Fixes: 0529c6b81761 ("rtlwifi: rtl8723ae: Update driver to match 06/28/14 Realtek version")
Fixes: c151aed6aa14 ("rtlwifi: rtl8188ee: Update driver to match Realtek release of 06282014")
Fixes: beb5bc402043 ("rtlwifi: rtl8192c-common: Convert common dynamic management routines for addition of rtl8192se and rtl8192de")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230928052327.120178-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74f7957c9b1b95553faaf146a2553e023a9d1720 ]
Since debugfs_create_file() return ERR_PTR and never return NULL, so use
IS_ERR() to check it instead of checking NULL.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230919050651.962694-1-ruanjinjie@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0201409079b975e46cc40e8bdff4bd61329ee10f ]
If, for any reason, the open-coded arithmetic causes a wraparound,
the protection that `struct_size()` adds against potential integer
overflows is defeated. Fix this by hardening call to `struct_size()`
with `size_add()`.
Fixes: 3f1071ec39f7 ("net: spider_net: Use struct_size() helper")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e22c6ea025013ae447fe269269753ffec763dde5 ]
If, for any reason, the open-coded arithmetic causes a wraparound, the
protection that `struct_size()` adds against potential integer overflows
is defeated. Fix this by hardening call to `struct_size()` with `size_mul()`.
Fixes: 2285ec872d9d ("mlxsw: spectrum_acl_bloom_filter: use struct_size() in kzalloc()")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d692873cbe861a870cdc9cbfb120eefd113c3dfd ]
If, for any reason, `tx_stats_num + rx_stats_num` wraps around, the
protection that struct_size() adds against potential integer overflows
is defeated. Fix this by hardening call to struct_size() with size_add().
Fixes: 691f4077d560 ("gve: Replace zero-length array with flexible-array member")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ca636d927a106780451d957734f02589b972e2b ]
Instead of freeing memory of a single VSI, make sure
the memory for all VSIs is cleared before releasing VSIs.
Add releasing of their resources in a loop with the iteration
number equal to the number of allocated VSIs.
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f771493da935299c6393ad3563b581255d01a37 ]
t4_set_params_timeout() can return -EINVAL if failed, add check
for this.
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77a8c982ff0d4c3a14022c6fe9e3dbfb327552ec ]
The I40E_TXR_FLAGS_WB_ON_ITR is i40e_ring flag and not i40e_pf one.
Fixes: 8e0764b4d6be42 ("i40e/i40evf: Add support for writeback on ITR feature for X722")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231023212714.178032-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4530e5b8e2dad63dcad2206232dd86e4b1489b6c ]
Call skb_gso_validate_network_len() to check if packet is over PMTU.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8d35024d4059ca550cba11ac9ab23a6c238d929 ]
The error handling in rtl8152_probe() is missing a call to release
firmware. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: 9370f2d05a2a ("r8152: support request_firmware for RTL8153")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb8adff9123e492598162ac1baad01a53891aef6 ]
The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: a028a9e003f2 ("r8152: move the settings of PHY to a work queue")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd17689526971c5ae12bc8398f34bd68cd0499e ]
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5feba71ec9c14a54c3babdc732c5b6866d8ee43 ]
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca082f019d8fbb983f03080487946da714154bae ]
strncat() usage in adf7242_debugfs_init() is wrong.
The size given to strncat() is the maximum number of bytes that can be
written, excluding the trailing NULL.
Here, the size that is passed, DNAME_INLINE_LEN, does not take into account
the size of "adf7242-" that is already in the array.
In order to fix it, use snprintf() instead.
Fixes: 7302b9d90117 ("ieee802154/adf7242: Driver for ADF7242 MAC IEEE802154")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c0b48e01daba5ca58f939a8425855d3f4f2ed14 ]
Add check for return of igb_update_ethtool_nfc_entry so that in case
of any potential errors the memory alocated for input will be freed.
Fixes: 0e71def25281 ("igb: add support of RX network flow classification")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f97eee484e71890131f9c563c5cc6d5a69e4308d ]
KCSAN reported the following data-race bug:
==================================================================
BUG: KCSAN: data-race in rtl8169_poll (drivers/net/ethernet/realtek/r8169_main.c:4430 drivers/net/ethernet/realtek/r8169_main.c:4583) r8169
race at unknown origin, with read to 0xffff888117e43510 of 4 bytes by interrupt on cpu 21:
rtl8169_poll (drivers/net/ethernet/realtek/r8169_main.c:4430 drivers/net/ethernet/realtek/r8169_main.c:4583) r8169
__napi_poll (net/core/dev.c:6527)
net_rx_action (net/core/dev.c:6596 net/core/dev.c:6727)
__do_softirq (kernel/softirq.c:553)
__irq_exit_rcu (kernel/softirq.c:427 kernel/softirq.c:632)
irq_exit_rcu (kernel/softirq.c:647)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1074 (discriminator 14))
asm_sysvec_apic_timer_interrupt (./arch/x86/include/asm/idtentry.h:645)
cpuidle_enter_state (drivers/cpuidle/cpuidle.c:291)
cpuidle_enter (drivers/cpuidle/cpuidle.c:390)
call_cpuidle (kernel/sched/idle.c:135)
do_idle (kernel/sched/idle.c:219 kernel/sched/idle.c:282)
cpu_startup_entry (kernel/sched/idle.c:378 (discriminator 1))
start_secondary (arch/x86/kernel/smpboot.c:210 arch/x86/kernel/smpboot.c:294)
secondary_startup_64_no_verify (arch/x86/kernel/head_64.S:433)
value changed: 0x80003fff -> 0x3402805f
Reported by Kernel Concurrency Sanitizer on:
CPU: 21 PID: 0 Comm: swapper/21 Tainted: G L 6.6.0-rc2-kcsan-00143-gb5cbe7c00aa0 #41
Hardware name: ASRock X670E PG Lightning/X670E PG Lightning, BIOS 1.21 04/26/2023
==================================================================
drivers/net/ethernet/realtek/r8169_main.c:
==========================================
4429
→ 4430 status = le32_to_cpu(desc->opts1);
4431 if (status & DescOwn)
4432 break;
4433
4434 /* This barrier is needed to keep us from reading
4435 * any other fields out of the Rx descriptor until
4436 * we know the status of DescOwn
4437 */
4438 dma_rmb();
4439
4440 if (unlikely(status & RxRES)) {
4441 if (net_ratelimit())
4442 netdev_warn(dev, "Rx ERROR. status = %08x\n",
Marco Elver explained that dma_rmb() doesn't prevent the compiler to tear up the access to
desc->opts1 which can be written to concurrently. READ_ONCE() should prevent that from
happening:
4429
→ 4430 status = le32_to_cpu(READ_ONCE(desc->opts1));
4431 if (status & DescOwn)
4432 break;
4433
As the consequence of this fix, this KCSAN warning was eliminated.
Fixes: 6202806e7c03a ("r8169: drop member opts1_mask from struct rtl8169_private")
Suggested-by: Marco Elver <elver@google.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: nic_swsd@realtek.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/lkml/dc7fc8fa-4ea4-e9a9-30a6-7c83e6b53188@alu.unizg.hr/
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This is at odds with sbalance, which balances this IRQ automatically.
Disable the IRQ affinity feature and leave this up to sbalance.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
[ Upstream commit 92fd39634541eb0a11bf1bafbc8ba92d6ddb8dba ]
Currently, whenever fw issues a change ownership event, the PF that owns
the fw tracer drops its ownership directly and the other PFs try to pick
up the ownership via what MTRC register suggests.
In some cases, driver releases the ownership of the tracer and reacquires
it later on. Whenever the driver releases ownership of the tracer, fw
issues a change ownership event. This event can be delayed and come after
driver has reacquired ownership of the tracer. Thus the late event will
trigger the tracer owner PF to release the ownership again and lead to a
scenario where no PF is owning the tracer.
To prevent the scenario described above, when handling a change
ownership event, do not drop ownership of the tracer directly, instead
read the fw MTRC register to retrieve the up-to-date owner of the tracer
and set it accordingly in driver level.
Fixes: f53aaa31cce7 ("net/mlx5: FW tracer, implement tracer logic")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a70e5cbedaf8ad10528ac9ac114f3ec20f422df ]
In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:
In file included from include/linux/skbuff.h:28,
from include/net/net_namespace.h:43,
from include/linux/netdevice.h:38,
from drivers/net/ethernet/marvell/sky2.c:18:
drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
1257 | dma_unmap_page(&pdev->dev, re->frag_addr[i],
| ^~~~~~~~~~~~~~
In file included from drivers/net/ethernet/marvell/sky2.c:41:
drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
2198 | dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
| ^~~~~~~~~
With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:
#define ETH_JUMBO_MTU 9000
causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 61b40cefe51af005c72dbdcf975a3d166c6e6406 upstream.
In bcm_sf2_mdio_register(), the class_find_device() will call get_device()
to increment reference count for priv->master_mii_bus->dev if
of_mdio_find_bus() succeeds. If mdiobus_alloc() or mdiobus_register()
fails, it will call get_device() twice without decrement reference count
for the device. And it is the same if bcm_sf2_mdio_register() succeeds but
fails in bcm_sf2_sw_probe(), or if bcm_sf2_sw_probe() succeeds. If the
reference count has not decremented to zero, the dev related resource will
not be freed.
So remove the get_device() in bcm_sf2_mdio_register(), and call
put_device() if mdiobus_alloc() or mdiobus_register() fails and in
bcm_sf2_mdio_unregister() to solve the issue.
And as Simon suggested, unwind from errors for bcm_sf2_mdio_register() and
just return 0 if it succeeds to make it cleaner.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231011032419.2423290-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc6f716a5069180c40a8c9b63631e97da34f64a3 upstream.
The hardware provides the indexes of the first and the last available
queue and VF. From the indexes, the driver calculates the numbers of
queues and VFs. In theory, a faulty device might say the last index is
smaller than the first index. In that case, the driver's calculation
would underflow, it would attempt to write to non-existent registers
outside of the ioremapped range and crash.
I ran into this not by having a faulty device, but by an operator error.
I accidentally ran a QE test meant for i40e devices on an ice device.
The test used 'echo i40e > /sys/...ice PCI device.../driver_override',
bound the driver to the device and crashed in one of the wr32 calls in
i40e_clear_hw.
Add checks to prevent underflows in the calculations of num_queues and
num_vfs. With this fix, the wrong device probing reports errors and
returns a failure without crashing.
Fixes: 838d41d92a90 ("i40e: clear all queues and interrupts")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Link: https://lore.kernel.org/r/20231011233334.336092-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f3389c73832ad90b63208c0fc281ad080114c7a upstream.
Driver allocates the LL2 rx buffers from kmalloc()
area to construct the skb using slab_build_skb()
The required size allocation seems to have overlooked
for accounting both skb_shared_info size and device
placement padding bytes which results into the below
panic when doing skb_put() for a standard MTU sized frame.
skbuff: skb_over_panic: text:ffffffffc0b0225f len:1514 put:1514
head:ff3dabceaf39c000 data:ff3dabceaf39c042 tail:0x62c end:0x566
dev:<NULL>
…
skb_panic+0x48/0x4a
skb_put.cold+0x10/0x10
qed_ll2b_complete_rx_packet+0x14f/0x260 [qed]
qed_ll2_rxq_handle_completion.constprop.0+0x169/0x200 [qed]
qed_ll2_rxq_completion+0xba/0x320 [qed]
qed_int_sp_dpc+0x1a7/0x1e0 [qed]
This patch fixes this by accouting skb_shared_info and device
placement padding size bytes when allocating the buffers.
Cc: David S. Miller <davem@davemloft.net>
Fixes: 0a7fb11c23c0 ("qed: Add Light L2 support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
