commit f78ca48a8ba9cdec96e8839351e49eec3233b177 upstream.
Currently we set SMBHSTCNT_LAST_BYTE only after the host has started
receiving the last byte. If we get e.g. preempted before setting
SMBHSTCNT_LAST_BYTE, the host may be finished with receiving the byte
before SMBHSTCNT_LAST_BYTE is set.
Therefore change the code to set SMBHSTCNT_LAST_BYTE before writing
SMBHSTSTS_BYTE_DONE for the byte before the last byte. Now the code
is also consistent with what we do in i801_isr_byte_done().
Reported-by: Jean Delvare <jdelvare@suse.com>
Closes: https://lore.kernel.org/linux-i2c/20230828152747.09444625@endymion.delvare/
Cc: stable@vger.kernel.org
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8183fa10c25c7b3c20670bf2b430ddcc1ee03c0 upstream.
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org
Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ac61d26b8baff5b2e5a9f3dc1ef63297e4b53e7 ]
Make sure we don't OOPS in case clock-frequency is set to 0 in a DT. The
variable set here is later used as a divisor.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 54f1840ddee9bbdc8dd89fbbfdfa632401244146 upstream.
When the `CONFIG_I2C_SLAVE` option is enabled and the device operates
as a slave, a situation arises where the master sends a START signal
without the accompanying STOP signal. This action results in a
persistent I2C bus timeout. The core issue stems from the fact that
the i2c controller remains in a slave read state without a timeout
mechanism. As a consequence, the bus perpetually experiences timeouts.
In this case, the i2c bus will be reset, but the slave_state reset is
missing.
Fixes: fee465150b45 ("i2c: aspeed: Reset the i2c controller when timeout occurs")
Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c896ff2dd8f30a6b0a922c83a96f6d43f05f0e92 upstream.
In case of SMBUS byte read with PEC enabled, the whole transfer
is split into two commands. A first write command, followed by
a read command. The write command does not have any PEC byte
and a PEC byte is appended at the end of the read command.
(cf Read byte protocol with PEC in SMBUS specification)
Within the STM32 I2C controller, handling (either sending
or receiving) of the PEC byte is done via the PECBYTE bit in
register CR2.
Currently, the PECBYTE is set at the beginning of a transfer,
which lead to sending a PEC byte at the end of the write command
(hence losing the real last byte), and also does not check the
PEC byte received during the read command.
This patch corrects the function stm32f7_i2c_smbus_xfer_msg
in order to only set the PECBYTE during the read command.
Fixes: 9e48155f6bfe ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I2C errors are quite common with these controllers and are non-fatal since
the transactions are retried. Silence the noisy logs so that dmesg isn't
destroyed by I2C log spam.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
IRQ balancing is already performed naturally by moving the i2c IRQ to the
CPU that kicks off an i2c transaction. Therefore, opt out from IRQ
balancing operations by setting IRQF_NOBALANCING.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
Hybrid mode could be switching between polling and interrupt mode. In
which case, we should always clear the pending IRQs to avoid spurious
interrupts.
Bug: 288490582
Test: Device boots, GCA, CTS
Signed-off-by: Edmond Chung <edmondchung@google.com>
Change-Id: Id33160b4c724cf800430c0833ce6703a5c2946ef
