commit de96f6a3003513c796bbe4e23210a446913f5c00 upstream.
This change fixes a rare issue where the PHY fails to detect a link
due to incorrect reset behavior.
The SW_RESET definition was incorrectly assigned to bit 14, which is the
Digital Restart bit according to the datasheet. This commit corrects
SW_RESET to bit 15 and assigns DIG_RESTART to bit 14 as per the
datasheet specifications.
The SW_RESET define is only used in the phy_reset function, which fully
re-initializes the PHY after the reset is performed. The change in the
bit definitions should not have any negative impact on the functionality
of the PHY.
v2:
- added Fixes tag
- improved commit message
Cc: stable@vger.kernel.org
Fixes: 5dc39fd5ef35 ("net: phy: DP83822: Add ability to advertise Fiber connection")
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Message-ID: <AS1P250MB0608A798661549BF83C4B43EA9462@AS1P250MB0608.EURP250.PROD.OUTLOOK.COM>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9234a2549cb6ac038bec36cc7c084218e9575513 ]
If phy_read_mmd() fails, the error code stored in 'bmsr' should be returned
instead of 'val' which is likely to be 0.
Fixes: 75f4d8d10e01 ("net: phy: add Broadcom BCM84881 PHY driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/3e1755b0c40340d00e089d6adae5bca2f8c79e53.1727982168.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a842e443ca8184f2dc82ab307b43a8b38defd6a5 ]
When configuring the fiber port, the DP83869 PHY driver incorrectly
calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit
number (10). This corrupts some other memory location -- in case of
arm64 the priv pointer in the same structure.
Since the advertising flags are updated from supported at the end of the
function the incorrect line isn't needed at all and can be removed.
Fixes: a29de52ba2a1 ("net: dp83869: Add ability to advertise Fiber connection")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241002161807.440378-1-inguin@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de7a670f8defe4ed2115552ad23dea0f432f7be4 ]
When the vsc73xx mdio bus work properly, the generic autonegotiation
configuration works well.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54a4e5c16382e871c01dd82b47e930fdce30406b ]
PHY_ID_KSZ9477 was supported but not added to the device table passed to
MODULE_DEVICE_TABLE.
Fixes: fc3973a1fa09 ("phy: micrel: add Microchip KSZ 9477 Switch PHY support")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96b2933152fd87b6a41765b2f58b158fde855b6 ]
If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will
not be run. As a consequence, `sfp_hwmon_remove()` is not getting
run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()`
itself checks `sfp->sm_mod_state` anyways, so this check was not
really needed in the first place.
Fixes: d2e816c0293f ("net: sfp: handle module remove outside state machine")
Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8a5c731fd1223090af57da33838c671a7fc6a78 ]
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292b5 ("net: phy: DP83822: Add setting the fixed internal delay")
Signed-off-by: Tim Pambor <tp@osasysteme.de>
Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621427fbdada788f18f77238e1c36f463c2cb9d1 ]
RGMII mode can be enable from dp83822 straps, and also writing bit 9
of register 0x17 - RMII and Status Register (RCSR).
When phy_interface_is_rgmii rgmii mode must be enabled, same for
contrary, this prevents malconfigurations of hw straps
References:
- https://www.ti.com/lit/gpn/dp83822i p66
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Alberto Bianchi <alberto.bianchi@amarulasolutions.com>
Tested-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: c8a5c731fd12 ("net: phy: dp83822: Fix RGMII TX delay configuration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4469c0c5b14a0919f5965c7ceac96b523eb57b79 ]
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec913b ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e398822c4751017fe401f57409488f5948d12fb5 ]
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 02d5fdbf4f2b8c406f7a4c98fa52aa181a11d733 upstream.
Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers using phylink, by calling netif_carrier_off in
phylink_create.
Fixes: 089381b27abe ("leds: initial support for Turris Omnia LEDs")
Cc: stable@vger.kernel.org
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e0a8c918daa58700609ebd45e3fcd49965be8bbc ]
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa904 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
