commit a71ed5898dfae68262f79277915d1dfe34586bc6 upstream.
"iw dev wlp2s0 station dump" shows incorrect rx bitrate:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 86.7 MBit/s VHT-MCS 9 VHT-NSS 1
This is because the RX band width is calculated incorrectly. Fix the
calculation according to the phydm_rxsc_2_bw() function from the
official drivers.
After:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 390.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 1
It also works correctly with the AP configured for 20 MHz and 40 MHz.
Tested with RTL8822CE.
Cc: stable@vger.kernel.org
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/bca8949b-e2bd-4515-98fd-70d3049a0097@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e735a4c6137262bcefe45bb52fde7b1f5fc6c4d ]
In 'rtw_wait_firmware_completion()', always wait for both (regular and
wowlan) firmware loading attempts. Otherwise if 'rtw_usb_intf_init()'
has failed in 'rtw_usb_probe()', 'rtw_usb_disconnect()' may issue
'ieee80211_free_hw()' when one of 'rtw_load_firmware_cb()' (usually
the wowlan one) is still in progress, causing UAF detected by KASAN.
Fixes: c8e5695eae99 ("rtw88: load wowlan firmware if wowlan is supported")
Reported-by: syzbot+6c6c08700f9480c41fe3@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6c6c08700f9480c41fe3
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240726114657.25396-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de4d4be4fa64ed7b4aa1c613061015bd8fa98b24 ]
Different channels have different TX power settings. rtl8192de is using
the TX power setting from the wrong channel in the 5 GHz band because
_rtl92c_phy_get_rightchnlplace expects an array which includes all the
channel numbers, but it's using an array which includes only the 5 GHz
channel numbers.
Use the array channel_all (defined in rtl8192de/phy.c) instead of
the incorrect channel5g (defined in core.c).
Tested only with rtl8192du, which will use the same TX power code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/c7653517-cf88-4f57-b79a-8edb0a8b32f0@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2f228d364da95ab58f63a3fedc00d5b2b7db16ab upstream.
Structs rx_desc_92d and rx_fwinfo_92d will not work for big endian
systems.
Delete rx_desc_92d because it's big and barely used, and instead use
the get_rx_desc_rxmcs and get_rx_desc_rxht functions, which work on big
endian systems too.
Fix rx_fwinfo_92d by duplicating four of its members in the correct
order.
Tested only with RTL8192DU, which will use the same code.
Tested only on a little endian system.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/698463da-5ef1-40c7-b744-fa51ad847caf@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7c0f48410f546772ac94a0f7b7291a15c4fc173 upstream.
Some (all?) management frames are incorrectly reported to mac80211 as
decrypted when actually the hardware did not decrypt them. This results
in speeds 3-5 times lower than expected, 20-30 Mbps instead of 100
Mbps.
Fix this by checking the encryption type field of the RX descriptor.
rtw88 does the same thing.
This fix was tested only with rtl8192du, which will use the same code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/4d600435-f0ea-46b0-bdb4-e60f173da8dd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08b5d052d17a89bb8706b2888277d0b682dc1610 upstream.
Don't subtract 1 from the power index. This was added in commit
2fc0b8e5a17d ("rtl8xxxu: Add TX power base values for gen1 parts")
for unknown reasons. The vendor drivers don't do this.
Also correct the calculations of values written to
REG_OFDM0_X{C,D}_TX_IQ_IMBALANCE. According to the vendor driver,
these are used for TX power training.
With these changes rtl8xxxu sets the TX power of RTL8192CU the same
as the vendor driver.
None of this appears to have any effect on my RTL8192CU device.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/6ae5945b-644e-45e4-a78f-4c7d9c987910@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c238adbc578eeb70cbc8fdd1bef3666b0f585b13 ]
total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just
ofdm_fa_cnt.
Fixes: 960361238b86 ("rtw88: 8821c: add false alarm statistics")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f3cb6d17-e4e4-44a7-9c9b-72aed994b5c9@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff1cc2fa3055ee4c83839f38b74b4ee370a2291c ]
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
Stable-dep-of: cb5942b77c05 ("wifi: wilc1000: prevent use-after-free on vif when cleaning up all interfaces")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1213acb478a7181cd73eeaf00db430f1e45b1361 ]
The workqueue might still be running, when the driver is stopped. To
avoid a use-after-free, call cancel_work_sync() in rtl8xxxu_stop().
Fixes: e542e66b7c2e ("rtl8xxxu: add bluetooth co-existence support for single antenna")
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240111163628.320697-2-martin.kaistra@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c16618bc06a41ad68fd8499a21d35ef57ca06c2 ]
Using calculate_bit_shift() to replace rtl8723_phy_calculate_bit_shift().
And fix an undefined bitwise shift behavior problem.
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-12-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e87ca403e2008b9e182239e1abbf6876a55eb33 ]
Add additional USB IDs found in the vendor driver from
https://github.com/Mange/rtl8192eu-linux-driver to support more
RTL8192EU devices.
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231217123017.1982-1-zenmchen@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5894d0089cbc146063dcc0239a78ede0a8142efb upstream.
The rtlwifi driver comes with custom code to write into PCIe Link
Control register. RMW access for the Link Control register requires
locking that is already provided by the standard PCIe capability
accessors.
Convert the custom RMW code writing into LNKCTL register to standard
RMW capability accessors. The accesses are changed to cover the full
LNKCTL register instead of touching just a single byte of the register.
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3943b3c2971444364e03224cfc828c5789deada upstream.
Ever since introduction in the commit 0c8173385e54 ("rtl8192ce: Add new
driver") the rtlwifi code has, according to comments, attempted to
disable/enable ASPM of the upstream bridge by writing into its LNKCTL
register. However, the code has never been correct because it performs
the writes to the device instead of the upstream bridge.
Worse yet, the offset where the PCIe capabilities reside is derived
from the offset of the upstream bridge. As a result, the write will use
an offset on the device that does not relate to the LNKCTL register
making the ASPM disable/enable code outright dangerous.
Because of those problems, there is no indication that the driver needs
disable/enable ASPM on the upstream bridge. As the Capabilities offset
is not correctly calculated for the write to target device's LNKCTL
register, the code is not disabling/enabling device's ASPM either.
Therefore, just remove the upstream bridge related ASPM disable/enable
code entirely.
The upstream bridge related ASPM code was the only user of the struct
mp_adapter members num4bytes, pcibridge_pciehdr_offset, and
pcibridge_linkctrlreg so those are removed as well.
Note: This change does not remove the code related to changing the
device's ASPM on purpose (which is independent of this flawed code
related to upstream bridge's ASPM).
Suggested-by: Bjorn Helgaas <bhelgaas@kernel.org>
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Fixes: 886e14b65a8f ("rtlwifi: Eliminate raw reads and writes from PCIe portion")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63526897fc0d086069bcab67c3a112caaec751cb ]
Using calculate_bit_shift() to replace _rtl92ee_phy_calculate_bit_shift().
And fix the undefined bitwise shift behavior problem.
Fixes: b1a3bfc97cd9 ("rtlwifi: rtl8192ee: Move driver from staging to the regular tree")
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-9-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b05897ca8c821a16ac03850c4704fe460b3f21a0 ]
Don't populate arrays the stack but instead make them static const. Replace
array channel_info with channel_all since it contains the same data as
channel_all. Makes object code smaller by 961 bytes.
Before:
text data bss dec hex filename
128147 44250 1024 173421 2a56d ../realtek/rtlwifi/rtl8192de/phy.o
After
text data bss dec hex filename
127122 44314 1024 172460 2a1ac ../realtek/rtlwifi/rtl8192de/phy.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210803144949.79433-2-colin.king@canonical.com
Stable-dep-of: b8b2baad2e65 ("wifi: rtlwifi: rtl8192de: using calculate_bit_shift()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d03e8231031bcc65a48cd88ef9c71b6524ce70b ]
Using calculate_bit_shift() to replace _rtl92c_phy_calculate_bit_shift().
And fix the undefined bitwise shift behavior problem.
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-7-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dedc3a6699d827d345019e921b8d8f37f694333 ]
Using calculate_bit_shift() to replace _rtl92c_phy_calculate_bit_shift().
And fix the undefined bitwise shift behavior problem.
Fixes: 4295cd254af3 ("rtlwifi: Move common parts of rtl8192ce/phy.c")
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-5-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 969bc926f04b438676768aeffffffb050e480b62 ]
Using calculate_bit_shift() to replace _rtl88e_phy_calculate_bit_shift().
And fix the undefined bitwise shift behavior problem.
Fixes: f0eb856e0b6c ("rtlwifi: rtl8188ee: Add new driver")
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-4-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52221dfddbbfb5b4e029bb2efe9bb7da33ec1e46 ]
There are many same functions like _rtl88e_phy_calculate_bit_shift(),
_rtl92c_phy_calculate_bit_shift() and so on. And these functions can
cause undefined bitwise shift behavior. Add calculate_bit_shift() to
replace them and fix undefined behavior in subsequent patches.
Signed-off-by: Su Hui <suhui@nfschina.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-2-suhui@nfschina.com
Stable-dep-of: 969bc926f04b ("wifi: rtlwifi: rtl8188ee: phy: using calculate_bit_shift()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc8263083af60e7e57c6120edbc1f75d6c909a35 ]
Clang static checker warns:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:184:49:
The result of the left shift is undefined due to shifting by '32',
which is greater or equal to the width of type 'u32'.
[core.UndefinedBinaryOperatorResult]
If the value of the right operand is negative or is greater than or
equal to the width of the promoted left operand, the behavior is
undefined.[1][2]
For example, when using different gcc's compilation optimization options
(-O0 or -O2), the result of '(u32)data << 32' is different. One is 0, the
other is old value of data. Let _rtl8821ae_phy_calculate_bit_shift()'s
return value less than 32 to fix this problem. Warn if bitmask is zero.
[1] https://stackoverflow.com/questions/11270492/what-does-the-c-standard-say-about-bitshifting-more-bits-than-the-width-of-type
[2] https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1256.pdf
Fixes: 21e4b0726dc6 ("rtlwifi: rtl8821ae: Move driver from staging to regular tree")
Signed-off-by: Su Hui <suhui@nfschina.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231127013511.26694-2-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53ee0b3b99edc6a47096bffef15695f5a895386f ]
The broadcast packets will be filtered in the FIF_ALLMULTI flag in
the original code, which causes beacon packets to be filtered out
and disconnection. Therefore, we fix it.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231103020851.102238-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3391ee7f9ea508c375d443cd712c2e699be235b4 ]
In 'rtl92c_dm_check_edca_turbo()', 'rtl88e_dm_check_edca_turbo()',
and 'rtl8723e_dm_check_edca_turbo()', the DL limit should be set
from the corresponding field of 'rtlpriv->btcoexist' rather than
UL. Compile tested only.
Fixes: 0529c6b81761 ("rtlwifi: rtl8723ae: Update driver to match 06/28/14 Realtek version")
Fixes: c151aed6aa14 ("rtlwifi: rtl8188ee: Update driver to match Realtek release of 06282014")
Fixes: beb5bc402043 ("rtlwifi: rtl8192c-common: Convert common dynamic management routines for addition of rtl8192se and rtl8192de")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230928052327.120178-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74f7957c9b1b95553faaf146a2553e023a9d1720 ]
Since debugfs_create_file() return ERR_PTR and never return NULL, so use
IS_ERR() to check it instead of checking NULL.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230919050651.962694-1-ruanjinjie@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
