commit 799d4b392417ed6889030a5b2335ccb6dcf030ab upstream.
When reading EDID fails and driver reports no modes available, the DRM
core adds an artificial 1024x786 mode to the connector. Unfortunately
some variants of the Exynos HDMI (like the one in Exynos4 SoCs) are not
able to drive such mode, so report a safe 640x480 mode instead of nothing
in case of the EDID reading failure.
This fixes the following issue observed on Trats2 board since commit
13d5b040363c ("drm/exynos: do not return negative values from .get_modes()"):
[drm] Exynos DRM: using 11c00000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 11c00000.fimd (ops fimd_component_ops)
exynos-drm exynos-drm: bound 12c10000.mixer (ops mixer_component_ops)
exynos-dsi 11c80000.dsi: [drm:samsung_dsim_host_attach] Attached s6e8aa0 device (lanes:4 bpp:24 mode-flags:0x10b)
exynos-drm exynos-drm: bound 11c80000.dsi (ops exynos_dsi_component_ops)
exynos-drm exynos-drm: bound 12d00000.hdmi (ops hdmi_component_ops)
[drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1
exynos-hdmi 12d00000.hdmi: [drm:hdmiphy_enable.part.0] *ERROR* PLL could not reach steady state
panel-samsung-s6e8aa0 11c80000.dsi.0: ID: 0xa2, 0x20, 0x8c
exynos-mixer 12c10000.mixer: timeout waiting for VSYNC
------------[ cut here ]------------
WARNING: CPU: 1 PID: 11 at drivers/gpu/drm/drm_atomic_helper.c:1682 drm_atomic_helper_wait_for_vblanks.part.0+0x2b0/0x2b8
[CRTC:70:crtc-1] vblank wait timed out
Modules linked in:
CPU: 1 PID: 11 Comm: kworker/u16:0 Not tainted 6.9.0-rc5-next-20240424 #14913
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x88
dump_stack_lvl from __warn+0x7c/0x1c4
__warn from warn_slowpath_fmt+0x11c/0x1a8
warn_slowpath_fmt from drm_atomic_helper_wait_for_vblanks.part.0+0x2b0/0x2b8
drm_atomic_helper_wait_for_vblanks.part.0 from drm_atomic_helper_commit_tail_rpm+0x7c/0x8c
drm_atomic_helper_commit_tail_rpm from commit_tail+0x9c/0x184
commit_tail from drm_atomic_helper_commit+0x168/0x190
drm_atomic_helper_commit from drm_atomic_commit+0xb4/0xe0
drm_atomic_commit from drm_client_modeset_commit_atomic+0x23c/0x27c
drm_client_modeset_commit_atomic from drm_client_modeset_commit_locked+0x60/0x1cc
drm_client_modeset_commit_locked from drm_client_modeset_commit+0x24/0x40
drm_client_modeset_commit from __drm_fb_helper_restore_fbdev_mode_unlocked+0x9c/0xc4
__drm_fb_helper_restore_fbdev_mode_unlocked from drm_fb_helper_set_par+0x2c/0x3c
drm_fb_helper_set_par from fbcon_init+0x3d8/0x550
fbcon_init from visual_init+0xc0/0x108
visual_init from do_bind_con_driver+0x1b8/0x3a4
do_bind_con_driver from do_take_over_console+0x140/0x1ec
do_take_over_console from do_fbcon_takeover+0x70/0xd0
do_fbcon_takeover from fbcon_fb_registered+0x19c/0x1ac
fbcon_fb_registered from register_framebuffer+0x190/0x21c
register_framebuffer from __drm_fb_helper_initial_config_and_unlock+0x350/0x574
__drm_fb_helper_initial_config_and_unlock from exynos_drm_fbdev_client_hotplug+0x6c/0xb0
exynos_drm_fbdev_client_hotplug from drm_client_register+0x58/0x94
drm_client_register from exynos_drm_bind+0x160/0x190
exynos_drm_bind from try_to_bring_up_aggregate_device+0x200/0x2d8
try_to_bring_up_aggregate_device from __component_add+0xb0/0x170
__component_add from mixer_probe+0x74/0xcc
mixer_probe from platform_probe+0x5c/0xb8
platform_probe from really_probe+0xe0/0x3d8
really_probe from __driver_probe_device+0x9c/0x1e4
__driver_probe_device from driver_probe_device+0x30/0xc0
driver_probe_device from __device_attach_driver+0xa8/0x120
__device_attach_driver from bus_for_each_drv+0x80/0xcc
bus_for_each_drv from __device_attach+0xac/0x1fc
__device_attach from bus_probe_device+0x8c/0x90
bus_probe_device from deferred_probe_work_func+0x98/0xe0
deferred_probe_work_func from process_one_work+0x240/0x6d0
process_one_work from worker_thread+0x1a0/0x3f4
worker_thread from kthread+0x104/0x138
kthread from ret_from_fork+0x14/0x28
Exception stack(0xf0895fb0 to 0xf0895ff8)
...
irq event stamp: 82357
hardirqs last enabled at (82363): [<c01a96e8>] vprintk_emit+0x308/0x33c
hardirqs last disabled at (82368): [<c01a969c>] vprintk_emit+0x2bc/0x33c
softirqs last enabled at (81614): [<c0101644>] __do_softirq+0x320/0x500
softirqs last disabled at (81609): [<c012dfe0>] __irq_exit_rcu+0x130/0x184
---[ end trace 0000000000000000 ]---
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [CRTC:70:crtc-1] commit wait timed out
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [CONNECTOR:74:HDMI-A-1] commit wait timed out
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [PLANE:56:plane-5] commit wait timed out
exynos-mixer 12c10000.mixer: timeout waiting for VSYNC
Cc: stable@vger.kernel.org
Fixes: 13d5b040363c ("drm/exynos: do not return negative values from .get_modes()")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38e3825631b1f314b21e3ade00b5a4d737eb054e upstream.
The duplicated EDID is never freed. Fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0a40097f0bc81deafc15f9195d1fb54595cd6d0 upstream.
Synchronize the dev->driver usage in really_probe() and dev_uevent().
These can run in different threads, what can result in the following
race condition for dev->driver uninitialization:
Thread #1:
==========
really_probe() {
...
probe_failed:
...
device_unbind_cleanup(dev) {
...
dev->driver = NULL; // <= Failed probe sets dev->driver to NULL
...
}
...
}
Thread #2:
==========
dev_uevent() {
...
if (dev->driver)
// If dev->driver is NULLed from really_probe() from here on,
// after above check, the system crashes
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
...
}
really_probe() holds the lock, already. So nothing needs to be done
there. dev_uevent() is called with lock held, often, too. But not
always. What implies that we can't add any locking in dev_uevent()
itself. So fix this race by adding the lock to the non-protected
path. This is the path where above race is observed:
dev_uevent+0x235/0x380
uevent_show+0x10c/0x1f0 <= Add lock here
dev_attr_show+0x3a/0xa0
sysfs_kf_seq_show+0x17c/0x250
kernfs_seq_show+0x7c/0x90
seq_read_iter+0x2d7/0x940
kernfs_fop_read_iter+0xc6/0x310
vfs_read+0x5bc/0x6b0
ksys_read+0xeb/0x1b0
__x64_sys_read+0x42/0x50
x64_sys_call+0x27ad/0x2d30
do_syscall_64+0xcd/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Similar cases are reported by syzkaller in
https://syzkaller.appspot.com/bug?extid=ffa8143439596313a85a
But these are regarding the *initialization* of dev->driver
dev->driver = drv;
As this switches dev->driver to non-NULL these reports can be considered
to be false-positives (which should be "fixed" by this commit, as well,
though).
The same issue was reported and tried to be fixed back in 2015 in
https://lore.kernel.org/lkml/1421259054-2574-1-git-send-email-a.sangwan@samsung.com/
already.
Fixes: 239378f16aa1 ("Driver core: add uevent vars for devices of a class")
Cc: stable <stable@kernel.org>
Cc: syzbot+ffa8143439596313a85a@syzkaller.appspotmail.com
Cc: Ashish Sangwan <a.sangwan@samsung.com>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Link: https://lore.kernel.org/r/20240513050634.3964461-1-dirk.behme@de.bosch.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 245f3b149e6cc3ac6ee612cdb7042263bfc9e73c upstream.
Update watermark will be done inside the hwfifo_set_watermark callback
just after the update_scan_mode. It is useless to do it here.
Fixes: 7f85e42a6c54 ("iio: imu: inv_icm42600: add buffer support in iio devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240527210008.612932-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 279428df888319bf68f2686934897301a250bb84 upstream.
The scale value for the temperature channel is (assuming Vref=2.5 and
the datasheet):
376.7897513
When calculating both val and val2 for the temperature scale we
use (3767897513/25) and multiply it by Vref (here I assume 2500mV) to
obtain:
2500 * (3767897513/25) ==> 376789751300
Finally we divide with remainder by 10^9 to get:
val = 376
val2 = 789751300
However, we return IIO_VAL_INT_PLUS_MICRO (should have been NANO) as
the scale type. So when converting the raw temperature value to the
'processed' temperature value we will get (assuming raw=810,
offset=-753):
processed = (raw + offset) * scale_val
= (810 + -753) * 376
= 21432
processed += div((raw + offset) * scale_val2, 10^6)
+= div((810 + -753) * 789751300, 10^6)
+= 45015
==> 66447
==> 66.4 Celcius
instead of the expected 21.5 Celsius.
Fix this issue by changing IIO_VAL_INT_PLUS_MICRO to
IIO_VAL_INT_PLUS_NANO.
Fixes: 56ca9db862bf ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Link: https://lore.kernel.org/r/20240501150554.1871390-1-marc.ferland@sonatest.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a01ef749b0a632f0e1f4ead0f08b3310d99fcb1 upstream.
According to the IIO documentation, the sign in the scan type should be
lower case. The ad9467 driver was incorrectly using upper case.
Fix by changing to lower case.
Fixes: 4606d0f4b05f ("iio: adc: ad9467: add support for AD9434 high-speed ADC")
Fixes: ad6797120238 ("iio: adc: ad9467: add support AD9467 ADC")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240503-ad9467-fix-scan-type-sign-v1-1-c7a1a066ebb9@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be27b896529787e23a35ae4befb6337ce73fcca0 ]
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 791b4089e326271424b78f2fae778b20e53d071b ]
Move the vxlan_features_check() call to after we verified the packet is
a tunneled VXLAN packet.
Without this, tunneled UDP non-VXLAN packets (for ex. GENENVE) might
wrongly not get offloaded.
In some cases, it worked by chance as GENEVE header is the same size as
VXLAN, but it is obviously incorrect.
Fixes: e3cfc7e6b7bd ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce62600c4dbee8d43b02277669dd91785a9b81d9 ]
Device managed panel bridge wrappers are created by calling to
drm_panel_bridge_add_typed() and registering a release handler for
clean-up when the device gets unbound.
Since the memory for this bridge is also managed and linked to the panel
device, the release function should not try to free that memory.
Moreover, the call to devm_kfree() inside drm_panel_bridge_remove() will
fail in this case and emit a warning because the panel bridge resource
is no longer on the device resources list (it has been removed from
there before the call to release handlers).
Fixes: 67022227ffb1 ("drm/bridge: Add a devm_ allocator for panel bridge.")
Signed-off-by: Adam Miotk <adam.miotk@arm.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610102739.139852-1-adam.miotk@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b880018edd3a577e50366338194dee9b899947e0 ]
komeda_pipeline_get_state() may return an error-valued pointer, thus
check the pointer for negative or null value before dereferencing.
Fixes: 502932a03fce ("drm/komeda: Add the initial scaler support for CORE")
Signed-off-by: Amjad Ouled-Ameur <amjad.ouled-ameur@arm.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610102056.40406-1-amjad.ouled-ameur@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44711b78608c98a3e6b49ce91678cd0917d5349 ]
In lio_vf_rep_copy_packet() pg_info->page is compared to a NULL value,
but then it is unconditionally passed to skb_add_rx_frag() which looks
strange and could lead to null pointer dereference.
lio_vf_rep_copy_packet() call trace looks like:
octeon_droq_process_packets
octeon_droq_fast_process_packets
octeon_droq_dispatch_pkt
octeon_create_recv_info
...search in the dispatch_list...
->disp_fn(rdisp->rinfo, ...)
lio_vf_rep_pkt_recv(struct octeon_recv_info *recv_info, ...)
In this path there is no code which sets pg_info->page to NULL.
So this check looks unneeded and doesn't solve potential problem.
But I guess the author had reason to add a check and I have no such card
and can't do real test.
In addition, the code in the function liquidio_push_packet() in
liquidio/lio_core.c does exactly the same.
Based on this, I consider the most acceptable compromise solution to
adjust this issue by moving skb_add_rx_frag() into conditional scope.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f233f327913 ("liquidio: switchdev support for LiquidIO NIC")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 968fde83841a8c23558dfbd0a0c69d636db52b55 ]
Currently hns3 ring buffer init process would hold cpu too long with big
Tx/Rx ring depth. This could cause soft lockup.
So this patch adds cond_resched() to the process. Then cpu can break to
run other tasks instead of busy looping.
Fixes: a723fb8efe29 ("net: hns3: refine for set ring parameters")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96b2933152fd87b6a41765b2f58b158fde855b6 ]
If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will
not be run. As a consequence, `sfp_hwmon_remove()` is not getting
run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()`
itself checks `sfp->sm_mod_state` anyways, so this check was not
really needed in the first place.
Fixes: d2e816c0293f ("net: sfp: handle module remove outside state machine")
Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb5e19d2dd03eb995ccd468d599b2337f7f66555 ]
This limit became a hard cap starting with the change referenced below.
Surface creation on the device will fail if the requested size is larger
than this limit so altering the value arbitrarily will expose modes that
are too large for the device's hard limits.
Fixes: 7ebb47c9f9ab ("drm/vmwgfx: Read new register for GB memory when available")
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240521184720.767-3-ian.forbes@broadcom.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 404ec4e4c169fb64da6b2a38b471c13ac0897c76 ]
Newer AMD systems can support multiple PCI segments, where each segment
contains one or more IOMMU instances. However, an IOMMU instance can only
support a single PCI segment.
Current code assumes that system contains only one pci segment (segment 0)
and creates global data structures such as device table, rlookup table,
etc.
Introducing per PCI segment data structure, which contains segment
specific data structures. This will eventually replace the global
data structures.
Also update `amd_iommu->pci_seg` variable to point to PCI segment
structure instead of PCI segment ID.
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20220706113825.25582-3-vasant.hegde@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Stable-dep-of: a295ec52c862 ("iommu/amd: Fix sysfs leak in iommu init")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 08af509efdf8dad08e972b48de0e2c2a7919ea8b upstream.
irq_set_type() should not implicitly unmask the IRQ.
All accesses to the interrupt configuration register are moved to a new
helper tqmx86_gpio_irq_config(). We also introduce the new rule that
accessing irq_type must happen while locked, which will become
significant for fixing EDGE_BOTH handling.
Fixes: b868db94a6a7 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/6aa4f207f77cb58ef64ffb947e91949b0f753ccd.1717063994.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4aa2dcfbad538adf7becd0034a3754e1bd01b2b5 ]
Syzkaller hit a warning [1] in a call to implement() when trying
to write a value into a field of smaller size in an output report.
Since implement() already has a warn message printed out with the
help of hid_warn() and value in question gets trimmed with:
...
value &= m;
...
WARN_ON may be considered superfluous. Remove it to suppress future
syzkaller triggers.
[1]
WARNING: CPU: 0 PID: 5084 at drivers/hid/hid-core.c:1451 implement drivers/hid/hid-core.c:1451 [inline]
WARNING: CPU: 0 PID: 5084 at drivers/hid/hid-core.c:1451 hid_output_report+0x548/0x760 drivers/hid/hid-core.c:1863
Modules linked in:
CPU: 0 PID: 5084 Comm: syz-executor424 Not tainted 6.9.0-rc7-syzkaller-00183-gcf87f46fd34d #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
RIP: 0010:implement drivers/hid/hid-core.c:1451 [inline]
RIP: 0010:hid_output_report+0x548/0x760 drivers/hid/hid-core.c:1863
...
Call Trace:
<TASK>
__usbhid_submit_report drivers/hid/usbhid/hid-core.c:591 [inline]
usbhid_submit_report+0x43d/0x9e0 drivers/hid/usbhid/hid-core.c:636
hiddev_ioctl+0x138b/0x1f00 drivers/hid/usbhid/hiddev.c:726
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:904 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Fixes: 95d1c8951e5b ("HID: simplify implement() a bit")
Reported-by: <syzbot+5186630949e3c55f0799@syzkaller.appspotmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0774d19038c496f0c3602fb505c43e1b2d8eed85 upstream.
If an input device declares too many capability bits then modalias
string for such device may become too long and not fit into uevent
buffer, resulting in failure of sending said uevent. This, in turn,
may prevent userspace from recognizing existence of such devices.
This is typically not a concern for real hardware devices as they have
limited number of keys, but happen with synthetic devices such as
ones created by xen-kbdfront driver, which creates devices as being
capable of delivering all possible keys, since it doesn't know what
keys the backend may produce.
To deal with such devices input core will attempt to trim key data,
in the hope that the rest of modalias string will fit in the given
buffer. When trimming key data it will indicate that it is not
complete by placing "+," sign, resulting in conversions like this:
old: k71,72,73,74,78,7A,7B,7C,7D,8E,9E,A4,AD,E0,E1,E4,F8,174,
new: k71,72,73,74,78,7A,7B,7C,+,
This should allow existing udev rules continue to work with existing
devices, and will also allow writing more complex rules that would
recognize trimmed modalias and check input device characteristics by
other means (for example by parsing KEY= data in uevent or parsing
input device sysfs attributes).
Note that the driver core may try adding more uevent environment
variables once input core is done adding its own, so when forming
modalias we can not use the entire available buffer, so we reduce
it by somewhat an arbitrary amount (96 bytes).
Reported-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Link: https://lore.kernel.org/r/ZjAWMQCJdrxZkvkB@google.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jason Andryuk <jason.andryuk@amd.com>
commit 4254dfeda82f20844299dca6c38cbffcfd499f41 upstream.
There is a potential out-of-bounds access when using test_bit() on a single
word. The test_bit() and set_bit() functions operate on long values, and
when testing or setting a single word, they can exceed the word
boundary. KASAN detects this issue and produces a dump:
BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas
Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965
For full log, please look at [1].
Make the allocation at least the size of sizeof(unsigned long) so that
set_bit() and test_bit() have sufficient room for read/write operations
without overwriting unallocated memory.
[1] Link: https://lore.kernel.org/all/ZkNcALr3W3KGYYJG@gmail.com/
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Cc: stable@vger.kernel.org
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240605085530.499432-1-leitao@debian.org
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91f7a1524a92c70ffe264db8bdfa075f15bbbeb9 upstream.
As described in commit 8f873c1ff4ca ("xhci: Blacklist using streams on the
Etron EJ168 controller"), EJ188 have the same issue as EJ168, where Streams
do not work reliable on EJ188. So apply XHCI_BROKEN_STREAMS quirk to EJ188
as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17bd54555c2aaecfdb38e2734149f684a73fa584 upstream.
As described in commit c877b3b2ad5c ("xhci: Add reset on resume quirk for
asrock p67 host"), EJ188 have the same issue as EJ168, where completely
dies on resume. So apply XHCI_RESET_ON_RESUME quirk to EJ188 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0260589b439e2637ad54a2b25f00a516ef28a57 upstream.
The transferred length is set incorrectly for cancelled bulk
transfer TDs in case the bulk transfer ring stops on the last transfer
block with a 'Stop - Length Invalid' completion code.
length essentially ends up being set to the requested length:
urb->actual_length = urb->transfer_buffer_length
Length for 'Stop - Length Invalid' cases should be the sum of all
TRB transfer block lengths up to the one the ring stopped on,
_excluding_ the one stopped on.
Fix this by always summing up TRB lengths for 'Stop - Length Invalid'
bulk cases.
This issue was discovered by Alan Stern while debugging
https://bugzilla.kernel.org/show_bug.cgi?id=218890, but does not
solve that bug. Issue is older than 4.10 kernel but fix won't apply
to those due to major reworks in that area.
Tested-by: Pierre Tomon <pierretom+12@ik.me>
Cc: stable@vger.kernel.org # v4.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 283cb234ef95d94c61f59e1cd070cd9499b51292 upstream.
The mei_me_pci_resume doesn't release irq on the error path,
in case mei_start() fails.
Cc: <stable@kernel.org>
Fixes: 33ec08263147 ("mei: revamp mei reset state machine")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240604090728.1027307-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22f00812862564b314784167a89f27b444f82a46 upstream.
The syzbot fuzzer found that the interrupt-URB completion callback in
the cdc-wdm driver was taking too long, and the driver's immediate
resubmission of interrupt URBs with -EPROTO status combined with the
dummy-hcd emulation to cause a CPU lockup:
cdc_wdm 1-1:1.0: nonzero urb status received: -71
cdc_wdm 1-1:1.0: wdm_int_callback - 0 bytes
watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [syz-executor782:6625]
CPU#0 Utilization every 4s during lockup:
#1: 98% system, 0% softirq, 3% hardirq, 0% idle
#2: 98% system, 0% softirq, 3% hardirq, 0% idle
#3: 98% system, 0% softirq, 3% hardirq, 0% idle
#4: 98% system, 0% softirq, 3% hardirq, 0% idle
#5: 98% system, 1% softirq, 3% hardirq, 0% idle
Modules linked in:
irq event stamp: 73096
hardirqs last enabled at (73095): [<ffff80008037bc00>] console_emit_next_record kernel/printk/printk.c:2935 [inline]
hardirqs last enabled at (73095): [<ffff80008037bc00>] console_flush_all+0x650/0xb74 kernel/printk/printk.c:2994
hardirqs last disabled at (73096): [<ffff80008af10b00>] __el1_irq arch/arm64/kernel/entry-common.c:533 [inline]
hardirqs last disabled at (73096): [<ffff80008af10b00>] el1_interrupt+0x24/0x68 arch/arm64/kernel/entry-common.c:551
softirqs last enabled at (73048): [<ffff8000801ea530>] softirq_handle_end kernel/softirq.c:400 [inline]
softirqs last enabled at (73048): [<ffff8000801ea530>] handle_softirqs+0xa60/0xc34 kernel/softirq.c:582
softirqs last disabled at (73043): [<ffff800080020de8>] __do_softirq+0x14/0x20 kernel/softirq.c:588
CPU: 0 PID: 6625 Comm: syz-executor782 Tainted: G W 6.10.0-rc2-syzkaller-g8867bbd4a056 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Testing showed that the problem did not occur if the two error
messages -- the first two lines above -- were removed; apparently adding
material to the kernel log takes a surprisingly large amount of time.
In any case, the best approach for preventing these lockups and to
avoid spamming the log with thousands of error messages per second is
to ratelimit the two dev_err() calls. Therefore we replace them with
dev_err_ratelimited().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Reported-and-tested-by: syzbot+5f996b83575ef4058638@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/00000000000073d54b061a6a1c65@google.com/
Reported-and-tested-by: syzbot+1b2abad17596ad03dcff@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000f45085061aa9b37e@google.com/
Fixes: 9908a32e94de ("USB: remove err() macro from usb class drivers")
Link: https://lore.kernel.org/linux-usb/40dfa45b-5f21-4eef-a8c1-51a2f320e267@rowland.harvard.edu/
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/29855215-52f5-4385-b058-91f42c2bee18@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55c421b364482b61c4c45313a535e61ed5ae4ea3 ]
Using __exit for the remove function results in the remove callback being
discarded with CONFIG_MMC_DAVINCI=y. When such a device gets unbound (e.g.
using sysfs or hotplug), the driver is just removed without the cleanup
being performed. This results in resource leaks. Fix it by compiling in the
remove callback unconditionally.
This also fixes a W=1 modpost warning:
WARNING: modpost: drivers/mmc/host/davinci_mmc: section mismatch in
reference: davinci_mmcsd_driver+0x10 (section: .data) ->
davinci_mmcsd_remove (section: .exit.text)
Fixes: b4cff4549b7a ("DaVinci: MMC: MMC/SD controller driver for DaVinci family")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240324114017.231936-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8492bd91aa055907c67ef04f2b56f6dadd1f44bf ]
When using a high speed clock with a low baud rate, the 4x prescaler is
automatically selected if required. In that case, sc16is7xx_set_baud()
properly configures the chip registers, but returns an incorrect baud
rate by not taking into account the prescaler value. This incorrect baud
rate is then fed to uart_update_timeout().
For example, with an input clock of 80MHz, and a selected baud rate of 50,
sc16is7xx_set_baud() will return 200 instead of 50.
Fix this by first changing the prescaler variable to hold the selected
prescaler value instead of the MCR bitfield. Then properly take into
account the selected prescaler value in the return value computation.
Also add better documentation about the divisor value computation.
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240430200431.4102923-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e57cefc4477659527f7adab1f87cdbf60ef1ae6 ]
To better show why the limit is what it is, since we have only 16 bits for
the divisor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8492bd91aa05 ("serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3626a6aebe62ce7067cdc460c0c644e9445386bb ]
[Why/How]
Theoretically rare corner case where ceil(Y) results in rounding
up to an integer. If this happens, the 1 should be carried over to
the X value.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24729b307eefcd7c476065cd7351c1a018082c19 ]
FFS based applications can utilize the aio_cancel() callback to dequeue
pending USB requests submitted to the UDC. There is a scenario where the
FFS application issues an AIO cancel call, while the UDC is handling a
soft disconnect. For a DWC3 based implementation, the callstack looks
like the following:
DWC3 Gadget FFS Application
dwc3_gadget_soft_disconnect() ...
--> dwc3_stop_active_transfers()
--> dwc3_gadget_giveback(-ESHUTDOWN)
--> ffs_epfile_async_io_complete() ffs_aio_cancel()
--> usb_ep_free_request() --> usb_ep_dequeue()
There is currently no locking implemented between the AIO completion
handler and AIO cancel, so the issue occurs if the completion routine is
running in parallel to an AIO cancel call coming from the FFS application.
As the completion call frees the USB request (io_data->req) the FFS
application is also referencing it for the usb_ep_dequeue() call. This can
lead to accessing a stale/hanging pointer.
commit b566d38857fc ("usb: gadget: f_fs: use io_data->status consistently")
relocated the usb_ep_free_request() into ffs_epfile_async_io_complete().
However, in order to properly implement locking to mitigate this issue, the
spinlock can't be added to ffs_epfile_async_io_complete(), as
usb_ep_dequeue() (if successfully dequeuing a USB request) will call the
function driver's completion handler in the same context. Hence, leading
into a deadlock.
Fix this issue by moving the usb_ep_free_request() back to
ffs_user_copy_worker(), and ensuring that it explicitly sets io_data->req
to NULL after freeing it within the ffs->eps_lock. This resolves the race
condition above, as the ffs_aio_cancel() routine will not continue
attempting to dequeue a request that has already been freed, or the
ffs_user_copy_work() not freeing the USB request until the AIO cancel is
done referencing it.
This fix depends on
commit b566d38857fc ("usb: gadget: f_fs: use io_data->status
consistently")
Fixes: 2e4c7553cd6f ("usb: gadget: f_fs: add aio support")
Cc: stable <stable@kernel.org> # b566d38857fc ("usb: gadget: f_fs: use io_data->status consistently")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240409014059.6740-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 323a359f9b077f382f4483023d096a4d316fd135 ]
On failed verification of PTP clock pin, error message prints channel
number instead of pin index after "pin", which is incorrect.
Fix error message by adding channel number to the message and printing
pin number instead of channel number.
Fixes: 6092315dfdec ("ptp: introduce programmable pins.")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20240604120555.16643-1-karol.kolacinski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cd4bc987abb2823836cbb8f887026011ccddc8a ]
Commit f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
has recently been added to vxlan mainly in the context of source
address snooping/learning so that when it is enabled, an entry in the
FDB is not being created for an invalid address for the corresponding
tunnel endpoint.
Before commit f58f45c1e5b9 vxlan was similarly behaving as geneve in
that it passed through whichever macs were set in the L2 header. It
turns out that this change in behavior breaks setups, for example,
Cilium with netkit in L3 mode for Pods as well as tunnel mode has been
passing before the change in f58f45c1e5b9 for both vxlan and geneve.
After mentioned change it is only passing for geneve as in case of
vxlan packets are dropped due to vxlan_set_mac() returning false as
source and destination macs are zero which for E/W traffic via tunnel
is totally fine.
Fix it by only opting into the is_valid_ether_addr() check in
vxlan_set_mac() when in fact source address snooping/learning is
actually enabled in vxlan. This is done by moving the check into
vxlan_snoop(). With this change, the Cilium connectivity test suite
passes again for both tunnel flavors.
Fixes: f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Bauer <mail@david-bauer.net>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb95f4535489ed830cf9b34b0a891e384d1aee4 ]
In case the firmware sends a notification that claims it has more data
than it has, we will read past that was allocated for the notification.
Remove the print of the buffer, we won't see it by default. If needed,
we can see the content with tracing.
This was reported by KFENCE.
Fixes: bdccdb854f2f ("iwlwifi: mvm: support MFUART dump in case of MFUART assert")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.ba82a01a559e.Ia91dd20f5e1ca1ad380b95e68aebf2794f553d9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60d62757df30b74bf397a2847a6db7385c6ee281 ]
In some versions of cfg80211, the ssids poinet might be a valid one even
though n_ssids is 0. Accessing the pointer in this case will cuase an
out-of-bound access. Fix this by checking n_ssids first.
Fixes: c1a7515393e4 ("iwlwifi: mvm: add adaptive dwell support")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240513132416.6e4d1762bf0d.I5a0e6cc8f02050a766db704d15594c61fe583d45@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87821b67dea87addbc4ab093ba752753b002176a ]
The driver should call iwl_dbg_tlv_free even if debugfs is not defined
since ini mode does not depend on debugfs ifdef.
Fixes: 68f6f492c4fa ("iwlwifi: trans: support loading ini TLVs from external file")
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.c8e3723f55b0.I5e805732b0be31ee6b83c642ec652a34e974ff10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a7aace2899711592327463c1a29ffee44fcc66e ]
We don't actually support >64 even for HE devices, so revert
back to 64. This fixes an issue where the session is refused
because the queue is configured differently from the actual
session later.
Fixes: 514c30696fbc ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.52f7b4cf83aa.If47e43adddf7fe250ed7f5571fbb35d8221c7c47@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 233e27b4d21c3e44eb863f03e566d3a22e81a7ae upstream.
When changing the maximum number of open zones, print that number
instead of the total number of zones.
Fixes: dc4d137ee3b7 ("null_blk: add support for max open/active zone limit for zoned devices")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240528062852.437599-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e03dbea2b0634b21a45946b4f8097e0dc86ebe1 upstream.
Currently, the affinity between QP cache and CQ cache is not
considered when assigning QPN, it will affect the message rate of HW.
Allocate QPN from QP cache with better CQ affinity to get better
performance.
Fixes: 71586dd20010 ("RDMA/hns: Create QP with selected QPN for bank load balance")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20230804012711.808069-5-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9293d3fcb70583f2c786f04ca788af026b7c4c5c upstream.
GFP_KERNEL may cause ida_alloc_range() to sleep, but the spinlock covering
this function is not allowed to sleep, so the spinlock needs to be changed
to mutex.
As there is a certain chance of memory allocation failure, GFP_ATOMIC is
not suitable for QP allocation scenarios.
Fixes: 71586dd20010 ("RDMA/hns: Create QP with selected QPN for bank load balance")
Link: https://lore.kernel.org/r/1611048513-28663-1-git-send-email-liweihang@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c422fbd5cb58c9a078172ae1e9750971b738a197 upstream.
The qunipro_g4_sel clear is also needed for new platforms with major
version > 5. Fix the version check to take this into account.
Fixes: 9c02aa24bf40 ("scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5")
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230821-topic-sm8x50-upstream-ufs-major-5-plus-v2-1-f42a4b712e58@linaro.org
Reviewed-by: "Bao D. Nguyen" <quic_nguyenb@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4f9d5a99a3fd1b1c691b7a1a6f8f3f25f4116c9 upstream.
A system crash like this
Failing address: 200000cb7df6f000 TEID: 200000cb7df6f403
Fault in home space mode while using kernel ASCE.
AS:00000002d71bc007 R3:00000003fe5b8007 S:000000011a446000 P:000000015660c13d
Oops: 0038 ilc:3 [#1] PREEMPT SMP
Modules linked in: mlx5_ib ...
CPU: 8 PID: 7556 Comm: bash Not tainted 6.9.0-rc7 #8
Hardware name: IBM 3931 A01 704 (LPAR)
Krnl PSW : 0704e00180000000 0000014b75e7b606 (ap_parse_bitmap_str+0x10e/0x1f8)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000001 ffffffffffffffc0 0000000000000001 00000048f96b75d3
000000cb00000100 ffffffffffffffff ffffffffffffffff 000000cb7df6fce0
000000cb7df6fce0 00000000ffffffff 000000000000002b 00000048ffffffff
000003ff9b2dbc80 200000cb7df6fcd8 0000014bffffffc0 000000cb7df6fbc8
Krnl Code: 0000014b75e7b5fc: a7840047 brc 8,0000014b75e7b68a
0000014b75e7b600: 18b2 lr %r11,%r2
#0000014b75e7b602: a7f4000a brc 15,0000014b75e7b616
>0000014b75e7b606: eb22d00000e6 laog %r2,%r2,0(%r13)
0000014b75e7b60c: a7680001 lhi %r6,1
0000014b75e7b610: 187b lr %r7,%r11
0000014b75e7b612: 84960021 brxh %r9,%r6,0000014b75e7b654
0000014b75e7b616: 18e9 lr %r14,%r9
Call Trace:
[<0000014b75e7b606>] ap_parse_bitmap_str+0x10e/0x1f8
([<0000014b75e7b5dc>] ap_parse_bitmap_str+0xe4/0x1f8)
[<0000014b75e7b758>] apmask_store+0x68/0x140
[<0000014b75679196>] kernfs_fop_write_iter+0x14e/0x1e8
[<0000014b75598524>] vfs_write+0x1b4/0x448
[<0000014b7559894c>] ksys_write+0x74/0x100
[<0000014b7618a440>] __do_syscall+0x268/0x328
[<0000014b761a3558>] system_call+0x70/0x98
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<0000014b75e7b636>] ap_parse_bitmap_str+0x13e/0x1f8
Kernel panic - not syncing: Fatal exception: panic_on_oops
occured when /sys/bus/ap/a[pq]mask was updated with a relative mask value
(like +0x10-0x12,+60,-90) with one of the numeric values exceeding INT_MAX.
The fix is simple: use unsigned long values for the internal variables. The
correct checks are already in place in the function but a simple int for
the internal variables was used with the possibility to overflow.
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Tested-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cae58516534e110f4a8558d48aa4435e15519121 upstream.
On AM62x, the watchdog is pet before the valid window is open. Fix
min_hw_heartbeat and accommodate a 2% + static offset safety margin.
The static offset accounts for max hardware error.
Remove the hack in the driver which shifts the open window boundary,
since it is no longer necessary due to the fix mentioned above.
cc: stable@vger.kernel.org
Fixes: 5527483f8f7c ("watchdog: rti-wdt: attach to running watchdog during probe")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240417205700.3947408-1-jm@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4f813c3ec9d1c32bc402becd1f011b3904dd699 upstream.
Add support for the Trace Hub in Meteor Lake-S CPU.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20240429130119.1518073-15-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3b17c6d9dddc2db3670bc9be628b122416a3d26 upstream.
Using completion_done to determine whether the caller has gone
away only works after a complete call. Furthermore it's still
possible that the caller has not yet called wait_for_completion,
resulting in another potential UAF.
Fix this by making the caller use cancel_work_sync and then freeing
the memory safely.
Fixes: 7d42e097607c ("crypto: qat - resolve race condition during AER recovery")
Cc: <stable@vger.kernel.org> #6.8+
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ad959b6703e2c4c5d7af03b4cfd5ff608036339 upstream.
The commit 04e5eac8f3ab("fbdev: savage: Error out if pixclock equals zero")
checks the value of pixclock to avoid divide-by-zero error. However
the function savagefb_probe doesn't handle the error return of
savagefb_check_var. When pixclock is 0, it will cause divide-by-zero error.
Fixes: 04e5eac8f3ab ("fbdev: savage: Error out if pixclock equals zero")
Signed-off-by: Cai Xinchen <caixinchen1@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef3eab75e17191e5665f52e64e85bc29d5705a7b upstream.
On the Toshiba WT10-A the microSD slot always reports the card being
write-protected, just like on the Toshiba WT8-B.
Add a DMI quirk to work around this.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-6-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3521d7cbaefff19cc656325787ed797e5f6a955 upstream.
The Lenovo Yoga Tablet 2 Pro 1380 sdcard slot has an active high cd pin
and a broken wp pin which always reports the card being write-protected.
Add a DMI quirk to address both issues.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-5-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63a7cd660246aa36af263b85c33ecc6601bf04be upstream.
Some mmc host drivers may need to fixup a card-detection GPIO's config
to e.g. enable the GPIO controllers builtin pull-up resistor on devices
where the firmware description of the GPIO is broken (e.g. GpioInt with
PullNone instead of PullUp in ACPI DSDT).
Since this is the exception rather then the rule adding a config
parameter to mmc_gpiod_request_cd() seems undesirable, so instead
add a new mmc_gpiod_set_cd_config() function. This is simply a wrapper
to call gpiod_set_config() on the card-detect GPIO acquired through
mmc_gpiod_request_cd().
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ed4477f2ea4743e7c5e1f9f3722152d14e6eeb1 upstream.
After the new V4L2 device node was registered, some additional
initialization was done before the device node was marked as
'registered'. During the time between creating the device node
and marking it as 'registered' it was possible to open the
device node, which would return -ENODEV since the 'registered'
flag was not yet set.
Hold the videodev_lock mutex from just before the device node
is registered until the 'registered' flag is set. Since v4l2_open
will take the same lock, it will wait until this registration
process is finished. This resolves this race condition.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: <stable@vger.kernel.org> # for vi4.18 and up
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 526f4527545b2d4ce0733733929fac7b6da09ac6 upstream.
When building for LoongArch with clang 18.0.0, the stack usage of
probe() is larger than the allowed 2048 bytes:
drivers/media/dvb-frontends/mxl5xx.c:1698:12: warning: stack frame size (2368) exceeds limit (2048) in 'probe' [-Wframe-larger-than]
1698 | static int probe(struct mxl *state, struct mxl5xx_cfg *cfg)
| ^
1 warning generated.
This is the result of the linked LLVM commit, which changes how the
arrays of structures in config_ts() get handled with
CONFIG_INIT_STACK_ZERO and CONFIG_INIT_STACK_PATTERN, which causes the
above warning in combination with inlining, as config_ts() gets inlined
into probe().
This warning can be easily fixed by moving the array of structures off
of the stackvia 'static const', which is a better location for these
variables anyways because they are static data that is only ever read
from, never modified, so allocating the stack space is wasteful.
This drops the stack usage from 2368 bytes to 256 bytes with the same
compiler and configuration.
Link: https://lore.kernel.org/linux-media/20240111-dvb-mxl5xx-move-structs-off-stack-v1-1-ca4230e67c11@kernel.org
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issues/1977
Link: afe8b93ffd
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4bc60736154bc9e0e39d3b88918f5d3762ebe5e0 upstream.
First the media device node was created, and if successful it was
marked as 'registered'. This leaves a small race condition where
an application can open the device node and get an error back
because the 'registered' flag was not yet set.
Change the order: first set the 'registered' flag, then actually
register the media device node. If that fails, then clear the flag.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes: cf4b9211b568 ("[media] media: Media device node support")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f228d364da95ab58f63a3fedc00d5b2b7db16ab upstream.
Structs rx_desc_92d and rx_fwinfo_92d will not work for big endian
systems.
Delete rx_desc_92d because it's big and barely used, and instead use
the get_rx_desc_rxmcs and get_rx_desc_rxht functions, which work on big
endian systems too.
Fix rx_fwinfo_92d by duplicating four of its members in the correct
order.
Tested only with RTL8192DU, which will use the same code.
Tested only on a little endian system.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/698463da-5ef1-40c7-b744-fa51ad847caf@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7c0f48410f546772ac94a0f7b7291a15c4fc173 upstream.
Some (all?) management frames are incorrectly reported to mac80211 as
decrypted when actually the hardware did not decrypt them. This results
in speeds 3-5 times lower than expected, 20-30 Mbps instead of 100
Mbps.
Fix this by checking the encryption type field of the RX descriptor.
rtw88 does the same thing.
This fix was tested only with rtl8192du, which will use the same code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/4d600435-f0ea-46b0-bdb4-e60f173da8dd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08b5d052d17a89bb8706b2888277d0b682dc1610 upstream.
Don't subtract 1 from the power index. This was added in commit
2fc0b8e5a17d ("rtl8xxxu: Add TX power base values for gen1 parts")
for unknown reasons. The vendor drivers don't do this.
Also correct the calculations of values written to
REG_OFDM0_X{C,D}_TX_IQ_IMBALANCE. According to the vendor driver,
these are used for TX power training.
With these changes rtl8xxxu sets the TX power of RTL8192CU the same
as the vendor driver.
None of this appears to have any effect on my RTL8192CU device.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/6ae5945b-644e-45e4-a78f-4c7d9c987910@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 151f66bb618d1fd0eeb84acb61b4a9fa5d8bb0fa upstream.
Xiao reported that lvm2 test lvconvert-raid-takeover.sh can hang with
small possibility, the root cause is exactly the same as commit
bed9e27baf52 ("Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"")
However, Dan reported another hang after that, and junxiao investigated
the problem and found out that this is caused by plugged bio can't issue
from raid5d().
Current implementation in raid5d() has a weird dependence:
1) md_check_recovery() from raid5d() must hold 'reconfig_mutex' to clear
MD_SB_CHANGE_PENDING;
2) raid5d() handles IO in a deadloop, until all IO are issued;
3) IO from raid5d() must wait for MD_SB_CHANGE_PENDING to be cleared;
This behaviour is introduce before v2.6, and for consequence, if other
context hold 'reconfig_mutex', and md_check_recovery() can't update
super_block, then raid5d() will waste one cpu 100% by the deadloop, until
'reconfig_mutex' is released.
Refer to the implementation from raid1 and raid10, fix this problem by
skipping issue IO if MD_SB_CHANGE_PENDING is still set after
md_check_recovery(), daemon thread will be woken up when 'reconfig_mutex'
is released. Meanwhile, the hang problem will be fixed as well.
Fixes: 5e2cf333b7bd ("md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d")
Cc: stable@vger.kernel.org # v5.19+
Reported-and-tested-by: Dan Moulding <dan@danm.net>
Closes: https://lore.kernel.org/all/20240123005700.9302-1-dan@danm.net/
Investigated-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240322081005.1112401-1-yukuai1@huaweicloud.com
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c81bf14f9db68311c2e75428eea070d97d603975 upstream.
Listed devices need the override for the keyboard to work.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4a89339f17c87c4990070e9116462d16e75894f upstream.
Commit defc9cd826e4 ("pata_legacy: resychronize with upstream changes and
resubmit") missed to update legacy_exit(), so that it now fails to do any
cleanup -- the loop body there can never be entered. Fix that and finally
remove now useless nr_legacy_host variable...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: defc9cd826e4 ("pata_legacy: resychronize with upstream changes and resubmit")
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b2faf1a4f3b6c748c0da36cda865a226534d520 upstream.
if the sdma_v4_0_irq_id_to_seq return -EINVAL, the process should
be stop to avoid out-of-bounds read, so directly return -EINVAL.
Signed-off-by: Bob Zhou <bob.zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cd4bc987abb2823836cbb8f887026011ccddc8a upstream.
Commit f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
has recently been added to vxlan mainly in the context of source
address snooping/learning so that when it is enabled, an entry in the
FDB is not being created for an invalid address for the corresponding
tunnel endpoint.
Before commit f58f45c1e5b9 vxlan was similarly behaving as geneve in
that it passed through whichever macs were set in the L2 header. It
turns out that this change in behavior breaks setups, for example,
Cilium with netkit in L3 mode for Pods as well as tunnel mode has been
passing before the change in f58f45c1e5b9 for both vxlan and geneve.
After mentioned change it is only passing for geneve as in case of
vxlan packets are dropped due to vxlan_set_mac() returning false as
source and destination macs are zero which for E/W traffic via tunnel
is totally fine.
Fix it by only opting into the is_valid_ether_addr() check in
vxlan_set_mac() when in fact source address snooping/learning is
actually enabled in vxlan. This is done by moving the check into
vxlan_snoop(). With this change, the Cilium connectivity test suite
passes again for both tunnel flavors.
Fixes: f58f45c1e5b9 ("vxlan: drop packets from invalid src-address")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Bauer <mail@david-bauer.net>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Backport note: vxlan snooping/learning not supported in 6.8 or older,
so commit is simply a revert. ]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67380251e8bbd3302c64fea07f95c31971b91c22 upstream.
Requesting a retune before switching to the RPMB partition has been
observed to cause CRC errors on the RPMB reads (-EILSEQ).
Since RPMB reads can not be retried, the clients would be directly
affected by the errors.
This commit disables the retune request prior to switching to the RPMB
partition: mmc_retune_pause() no longer triggers a retune before the
pause period begins.
This was verified with the sdhci-of-arasan driver (ZynqMP) configured
for HS200 using two separate eMMC cards (DG4064 and 064GB2). In both
cases, the error was easy to reproduce triggering every few tenths of
reads.
With this commit, systems that were utilizing OP-TEE to access RPMB
variables will experience an enhanced performance. Specifically, when
OP-TEE is configured to employ RPMB as a secure storage solution, it not
only writes the data but also the secure filesystem within the
partition. As a result, retrieving any variable involves multiple RPMB
reads, typically around five.
For context, on ZynqMP, each retune request consumed approximately
8ms. Consequently, reading any RPMB variable used to take at the very
minimum 40ms.
After droping the need to retune before switching to the RPMB partition,
this is no longer the case.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240103112911.2954632-1-jorge@foundries.io
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52a2c70c3ec555e670a34dd1ab958986451d2dd2 ]
The property name is "sensirion,low-precision", not
"sensicon,low-precision".
Cc: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Fixes: be7373b60df5 ("hwmon: shtc1: add support for device tree bindings")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95d7c452a26564ef0c427f2806761b857106d8c4 ]
The dev_warn to notify about a spurious interrupt was introduced with
the reasoning that these are unexpected. However spurious interrupts
tend to trigger continously and the error message on the serial console
prevents that the core's detection of spurious interrupts kicks in
(which disables the irq) and just floods the console.
Fixes: c64e7efe46b7 ("spi: stm32: make spurious and overrun interrupts visible")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://msgid.link/r/20240521105241.62400-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf0497f53c8535f99b72041529d3f7708a6e2c0d ]
When fec_probe() fails or fec_drv_remove() needs to release the
fec queue and remove a NAPI context, therefore add a function
corresponding to fec_enet_init() and call fec_enet_deinit() which
does the opposite to release memory and remove a NAPI context.
Fixes: 59d0f7465644 ("net: fec: init multi queue date structure")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240524050528.4115581-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52a2f0608366a629d43dacd3191039c95fef74ba ]
LED Select (LED_SEL) bit in the LED General Purpose IO Configuration
register is used to determine the functionality of external LED pins
(Speed Indicator, Link and Activity Indicator, Full Duplex Link
Indicator). The default value for this bit is 0 when no EEPROM is
present. If a EEPROM is present, the default value is the value of the
LED Select bit in the Configuration Flags of the EEPROM. A USB Reset or
Lite Reset (LRST) will cause this bit to be restored to the image value
last loaded from EEPROM, or to be set to 0 if no EEPROM is present.
While configuring the dual purpose GPIO/LED pins to LED outputs in the
LED General Purpose IO Configuration register, the LED_SEL bit is changed
as 0 and resulting the configured value from the EEPROM is cleared. The
issue is fixed by using read-modify-write approach.
Fixes: f293501c61c5 ("smsc95xx: configure LED outputs")
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Link: https://lore.kernel.org/r/20240523085314.167650-1-Parthiban.Veerasooran@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8021b94b0412c37bcc79027c2e382086b6ce449 ]
enic_set_vf_port assumes that the nl attribute IFLA_PORT_PROFILE
is of length PORT_PROFILE_MAX and that the nl attributes
IFLA_PORT_INSTANCE_UUID, IFLA_PORT_HOST_UUID are of length PORT_UUID_MAX.
These attributes are validated (in the function do_setlink in rtnetlink.c)
using the nla_policy ifla_port_policy. The policy defines IFLA_PORT_PROFILE
as NLA_STRING, IFLA_PORT_INSTANCE_UUID as NLA_BINARY and
IFLA_PORT_HOST_UUID as NLA_STRING. That means that the length validation
using the policy is for the max size of the attributes and not on exact
size so the length of these attributes might be less than the sizes that
enic_set_vf_port expects. This might cause an out of bands
read access in the memcpys of the data of these
attributes in enic_set_vf_port.
Fixes: f8bd909183ac ("net: Add ndo_{set|get}_vf_port support for enic dynamic vnics")
Signed-off-by: Roded Zats <rzats@paloaltonetworks.com>
Link: https://lore.kernel.org/r/20240522073044.33519-1-rzats@paloaltonetworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b794918961516f667b0c745aebdfebbb8a98df39 ]
Since commit a6aa8fca4d79 ("dma-buf/sw-sync: Reduce irqsave/irqrestore from
known context") by error replaced spin_unlock_irqrestore() with
spin_unlock_irq() for both sync_debugfs_show() and sync_print_obj() despite
sync_print_obj() is called from sync_debugfs_show(), lockdep complains
inconsistent lock state warning.
Use plain spin_{lock,unlock}() for sync_print_obj(), for
sync_debugfs_show() is already using spin_{lock,unlock}_irq().
Reported-by: syzbot <syzbot+a225ee3df7e7f9372dbe@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=a225ee3df7e7f9372dbe
Fixes: a6aa8fca4d79 ("dma-buf/sw-sync: Reduce irqsave/irqrestore from known context")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c2e46020-aaa6-4e06-bf73-f05823f913f0@I-love.SAKURA.ne.jp
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c74195d5dd977e97556e6fa76909b831c241230 ]
Previously, the driver incorrectly used rx_dropped to report device
buffer exhaustion.
According to the documentation, rx_dropped should not be used to count
packets dropped due to buffer exhaustion, which is the purpose of
rx_missed_errors.
Use rx_missed_errors as intended for counting packets dropped due to
buffer exhaustion.
Fixes: 269e6b3af3bf ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f97914e35fd98b2b18fb8a092e0a0799f73afdfe ]
When disabling an nvmet namespace, there is a period where the
subsys->lock is released, as the ns disable waits for backend IO to
complete, and the ns percpu ref to be properly killed. The original
intent was to avoid taking the subsystem lock for a prolong period as
other processes may need to acquire it (for example new incoming
connections).
However, it opens up a window where another process may come in and
enable the ns, (re)intiailizing the ns percpu_ref, causing the disable
sequence to hang.
Solve this by taking the global nvmet_config_sem over the entire configfs
enable/disable sequence.
Fixes: a07b4970f464 ("nvmet: add a generic NVMe target")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f788ba457b45b0ce422943fcec9fa35c4587764 ]
There is no need to set the DMA mapped flag of the message if it has
no mapped transfers. Moreover, it may give the code a chance to take
the wrong paths, i.e. to exercise DMA related APIs on unmapped data.
Make __spi_map_msg() to bail earlier on the above mentioned cases.
Fixes: 99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240522171018.3362521-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b1c92f8e5371700fada307cc8fd2c51fa7bc8c1 ]
The assignment of pps_enable is protected by tmreg_lock, but the read
operation of pps_enable is not. So the Coverity tool reports a lock
evasion warning which may cause data race to occur when running in a
multithread environment. Although this issue is almost impossible to
occur, we'd better fix it, at least it seems more logically reasonable,
and it also prevents Coverity from continuing to issue warnings.
Fixes: 278d24047891 ("net: fec: ptp: Enable PPS output based on ptp clock")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240521023800.17102-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f9f7c63c415e287cd57b5c98be61eb320dedcfc ]
Some of the regulators on the BD71828 have common voltage setting for
RUN/SUSPEND/IDLE/LPSR states. The enable control can be set for each
state though.
The driver allows setting the voltage values for these states via
device-tree. As a side effect, setting the voltages for
SUSPEND/IDLE/LPSR will also change the RUN level voltage which is not
desired and can break the system.
The comment in code reflects this behaviour, but it is likely to not
make people any happier. The right thing to do is to allow setting the
enable/disable state at SUSPEND/IDLE/LPSR via device-tree, but to
disallow setting state specific voltages for those regulators.
BUCK1 is a bit different. It only shares the SUSPEND and LPSR state
voltages. The former behaviour of allowing to silently overwrite the
SUSPEND state voltage by LPSR state voltage is also changed here so that
the SUSPEND voltage is prioritized over LPSR voltage.
Prevent setting PMIC state specific voltages for regulators which do not
support it.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 522498f8cb8c ("regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators")
Link: https://msgid.link/r/e1883ae1e3ae5668f1030455d4750923561f3d68.1715848512.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe499977bc36fedae89f0a0d7deb4ccde9798fe ]
If, when waiting for a transmit to finish, the wait is interrupted,
then you might get a "transmit timed out" message, even though the
transmit was interrupted and did not actually time out.
Set transmit_in_progress_aborted to true if the
wait_for_completion_killable() call was interrupted and ensure
that the transmit is properly marked as ABORTED.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Yang, Chenyuan <cy54@illinois.edu>
Closes: https://lore.kernel.org/linux-media/PH7PR11MB57688E64ADE4FE82E658D86DA09EA@PH7PR11MB5768.namprd11.prod.outlook.com/
Fixes: 590a8e564c6e ("media: cec: abort if the current transmit was canceled")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42bcaacae924bf18ae387c3f78c202df0b739292 ]
When cec_release() uses fh->msgs it has to take fh->lock,
otherwise the list can get corrupted.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Yang, Chenyuan <cy54@illinois.edu>
Closes: https://lore.kernel.org/linux-media/PH7PR11MB57688E64ADE4FE82E658D86DA09EA@PH7PR11MB5768.namprd11.prod.outlook.com/
Fixes: ca684386e6e2 ("[media] cec: add HDMI CEC framework (api)")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f62dc8f6bf82d1b307fc37d8d22cc79f67856c2f ]
Commit d725d20e81c2 ("media: flexcop-usb: sanity checking of endpoint type
") adds a sanity check for endpoint[1], but fails to modify the sanity
check of bNumEndpoints.
Fix this by modifying the sanity check of bNumEndpoints to 2.
Link: https://lore.kernel.org/linux-media/20220602055027.849014-1-dzm91@hust.edu.cn
Fixes: d725d20e81c2 ("media: flexcop-usb: sanity checking of endpoint type")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3de50478b5cc2e0c2479a5f2b967f331f7597d23 ]
Add a temporary variable to make the endpoint sanity checks a bit more
readable.
While at it, fix a typo in the usb_set_interface() comment.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220822151456.27178-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f62dc8f6bf82 ("media: flexcop-usb: fix sanity check of bNumEndpoints")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37f1663c91934f664fb850306708094a324c227c ]
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated [1]. In an effort
to remove strlcpy() completely [2], replace strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Link: https://lore.kernel.org/r/20230516025404.2843867-1-azeemshaikh38@gmail.com
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: c3408c4ae041 ("scsi: qla2xxx: Avoid possible run-time warning with long model_num")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faa4364bef2ec0060de381ff028d1d836600a381 ]
The subtract in this condition is reversed. The ->length is the length
of the buffer. The ->bytesused is how many bytes we have copied thus
far. When the condition is reversed that means the result of the
subtraction is always negative but since it's unsigned then the result
is a very high positive value. That means the overflow check is never
true.
Additionally, the ->bytesused doesn't actually work for this purpose
because we're not writing to "buf->mem + buf->bytesused". Instead, the
math to calculate the destination where we are writing is a bit
involved. You calculate the number of full lines already written,
multiply by two, skip a line if necessary so that we start on an odd
numbered line, and add the offset into the line.
To fix this buffer overflow, just take the actual destination where we
are writing, if the offset is already out of bounds print an error and
return. Otherwise, write up to buf->length bytes.
Fixes: 9cb2173e6ea8 ("[media] media: Add stk1160 new driver (easycap replacement)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30ea09a182cb37c4921b9d477ed18107befe6d78 ]
The bridge always uses 24bpp internally. Therefore, for jeida-18
mapping we need to discard the lowest two bits for each channel and thus
starting with LV_[RGB]2. jeida-24 has the same mapping but uses four
lanes instead of three, with the forth pair transmitting the lowest two
bits of each channel. Thus, the mapping between jeida-18 and jeida-24
is actually the same, except that one channel is turned off (by
selecting the RGB666 format in VPCTRL).
While at it, remove the bogus comment about the hardware default because
the default is overwritten in any case.
Tested with a jeida-18 display (Evervision VGG644804).
Fixes: b26975593b17 ("display/drm/bridge: TC358775 DSI/LVDS driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240225062008.33191-5-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48c0687a322d54ac7e7a685c0b6db78d78f593af ]
The output voltage is inclusive hence the max level calculation is
off-by-one-step. Correct it.
iWhile we are at it also add a define for the step size instead of
using the magic value.
Fixes: 11205bb63e5c ("Input: add support for pm8xxx based vibrator driver")
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240412-pm8xxx-vibrator-new-design-v10-1-0ec0ad133866@quicinc.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3182932bb070e7518411fd165e023f82afd7d25 ]
While STRB is currently used for DATA and CRC responses, the CMD
responses from the device to the host still require ITAPDLY for
HS400 timing.
Currently what is stored for HS400 is the ITAPDLY from High Speed
mode which is incorrect. The ITAPDLY for HS400 speed mode should
be the same as ITAPDLY as HS200 timing after tuning is executed.
Add the functionality to save ITAPDLY from HS200 tuning and save
as HS400 ITAPDLY.
Fixes: a161c45f2979 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-8-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dff65bb5e09903c27d9cff947dff4d22b6ea6a1 ]
Add ITAPDLYSEL to sdhci_j721e_4bit_set_clock function.
This allows to set the correct ITAPDLY for timings that
do not carry out tuning.
Fixes: 1accbced1c32 ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-7-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 387c1bf7dce0dfea02080c8bdb066b5209e92155 ]
Currently the OTAP/ITAP delay enable functionality is incorrect in
the am654_set_clock function. The OTAP delay is not enabled when
timing < SDR25 bus speed mode. The ITAP delay is not enabled for
timings that do not carry out tuning.
Add this OTAP/ITAP delay functionality according to the datasheet
[1] OTAPDLYENA and ITAPDLYENA for MMC0.
[1] https://www.ti.com/lit/ds/symlink/am62p.pdf
Fixes: 8ee5fc0e0b3b ("mmc: sdhci_am654: Update OTAPDLY writes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-4-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cb2f9286a31f33dc732c57540838ad9339393ab ]
ti,otap-del-sel has been deprecated since v5.7 and there are no users of
this property and no documentation in the DT bindings either.
Drop the fallback code looking for this property, this makes
sdhci_am654_get_otap_delay() much easier to read as all the TAP values
can be handled via a single iterator loop.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231122060215.2074799-1-vigneshr@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 387c1bf7dce0 ("mmc: sdhci_am654: Add OTAP/ITAP delay enable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d465234493bb6ad1b9c10a0c9ef9881b8d85081a ]
For DDR52 timing, DLL is enabled but tuning is not carried
out, therefore the ITAPDLY value in PHY CTRL 4 register is
not correct. Fix this by writing ITAPDLY after enabling DLL.
Fixes: a161c45f2979 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-3-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6231d99dd4119312ad41abf9383e18fec66cbe4b ]
Currently the sdhci_am654 driver only supports one tuning
algorithm which should be used only when DLL is enabled. The
ITAPDLY is selected from the largest passing window and the
buffer is viewed as a circular buffer.
The new algorithm should be used when the delay chain
is enabled. The ITAPDLY is selected from the largest passing
window and the buffer is not viewed as a circular buffer.
This implementation is based off of the following paper: [1].
Also add support for multiple failing windows.
[1] https://www.ti.com/lit/an/spract9/spract9.pdf
Fixes: 13ebeae68ac9 ("mmc: sdhci_am654: Add support for software tuning")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-2-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d40e9edcf3eb925c259df9f9dd7319a4fcbc675b ]
Without the device table the driver will not auto-load when compiled as
a module.
Fixes: 273db8f03509 ("Input: add IOC3 serio driver")
Signed-off-by: Karel Balej <balejk@matfyz.cz>
Link: https://lore.kernel.org/r/20240313115832.8052-1-balejk@matfyz.cz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 150e792dee9ca8416f3d375e48f2f4d7f701fc6b ]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230920125829.1478827-37-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: d40e9edcf3eb ("Input: ioc3kbd - add device table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf32bceedd0453c70d9d022e2e29f98e446d7161 ]
clang warns about a string overflow in this driver
drivers/input/misc/ims-pcu.c:1802:2: error: 'snprintf' will always be truncated; specified size is 10, but format string expands to at least 12 [-Werror,-Wformat-truncation]
drivers/input/misc/ims-pcu.c:1814:2: error: 'snprintf' will always be truncated; specified size is 10, but format string expands to at least 12 [-Werror,-Wformat-truncation]
Make the buffer a little longer to ensure it always fits.
Fixes: 628329d52474 ("Input: add IMS Passenger Control Unit driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240326223825.4084412-7-arnd@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aae20f6e34cd0cbd67a1d0e5877561c40109a81b ]
The to-be-fixed commit removed locking when invalidating the DMA RX
descriptors on shutdown. It overlooked that there is still a rx_timer
running which may still access the protected data. So, re-add the
locking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/r/ee6c9e16-9f29-450e-81da-4a8dceaa8fc7@de.bosch.com
Fixes: 2c4ee23530ff ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-7-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2e78a294a8a863898b781dbcf90e087eda3155d ]
The "Downstream Port Containment related Enhancements" ECN of Jan 28, 2019
(document 12888 below), defined the EDR_PORT_LOCATE_DSM function with
Revision ID 5 with a return value encoding (Bits 2:0 = Function, Bits 7:3 =
Device, Bits 15:8 = Bus). When the ECN was integrated into PCI Firmware
r3.3, sec 4.6.13, Bit 31 was added to indicate success or failure.
Check Bit 31 for failure in acpi_dpc_port_get().
Link: https://lore.kernel.org/r/20240501022543.1626025-1-sathyanarayanan.kuppuswamy@linux.intel.com
Link: https://members.pcisig.com/wg/PCI-SIG/document/12888
Fixes: ac1c8e35a326 ("PCI/DPC: Add Error Disconnect Recover (EDR) support")
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
[bhelgaas: split into two patches, update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Satish Thatchanamurthy <Satish.Thatchanamurt@Dell.com> # one platform
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24ba846133d0edec785ac6430d4daf6e9c93a09 ]
The "Downstream Port Containment related Enhancements" ECN of Jan 28, 2019
(document 12888 below), defined the EDR_PORT_DPC_ENABLE_DSM function with
Revision ID 5 with Arg3 being an integer. But when the ECN was integrated
into PCI Firmware r3.3, sec 4.6.12, it was defined as Revision ID 6 with
Arg3 being a package containing an integer.
The implementation in acpi_enable_dpc() supplies a package as Arg3 (arg4 in
the code), but it previously specified Revision ID 5. Align this with PCI
Firmware r3.3 by using Revision ID 6.
If firmware implemented per the ECN, its Revision 5 function would receive
a package as Arg3 when it expects an integer, so acpi_enable_dpc() would
likely fail. If such firmware exists and lacks a Revision 6 function that
expects a package, we may have to add support for Revision 5.
Link: https://lore.kernel.org/r/20240501022543.1626025-1-sathyanarayanan.kuppuswamy@linux.intel.com
Link: https://members.pcisig.com/wg/PCI-SIG/document/12888
Fixes: ac1c8e35a326 ("PCI/DPC: Add Error Disconnect Recover (EDR) support")
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
[bhelgaas: split into two patches, update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Satish Thatchanamurthy <Satish.Thatchanamurt@Dell.com> # one platform
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1781d0a1458070d40134e4f3412ec9d70099bec ]
IRQ_DOMAIN is a hidden (not user visible) symbol. Users cannot set
it directly thru "make *config", so drivers should select it instead
of depending on it if they need it.
Relying on it being set for a dependency is risky.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change EXTCON_MAX8997's use of "depends on" for
IRQ_DOMAIN to "select".
Link: https://lore.kernel.org/lkml/20240213060028.9744-1-rdunlap@infradead.org/
Fixes: dca1a71e4108 ("extcon: Add support irq domain for MAX8997 muic")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbf740aeb86a4fe82ad158d26d711f2f3be79b3e ]
In register_device, the return value of ida_simple_get is unchecked,
in witch ida_simple_get will use an invalid index value.
To address this issue, index should be checked after ida_simple_get. When
the index value is abnormal, a warning message should be printed, the port
should be dropped, and the value should be recorded.
Fixes: 9a69645dde11 ("ppdev: fix registering same device name")
Signed-off-by: Huai-Yuan Liu <qq810974084@gmail.com>
Link: https://lore.kernel.org/r/20240412083840.234085-1-qq810974084@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8407f71ebeaeb6f50bd89791837873e44609708 ]
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
This is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/ba9da12fdd5cdb2c28180b7160af5042447d803f.1702962092.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: fbf740aeb86a ("ppdev: Add an error check in register_device")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3df463865ba42b8f88a590326f4c9ea17a1ce459 ]
The put_device(&stm->dev) call will trigger stm_device_release() which
frees "stm" so the vfree(stm) on the next line is a double free.
Fixes: 389b6699a2aa ("stm class: Fix stm device initialization order")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: https://lore.kernel.org/r/20240429130119.1518073-2-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7c0e1ecee403a43abc89eb3e75672b01ff2ece9 ]
The current implementation of the fpga region assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the region
during programming if the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_region
struct and use it to take the module's refcount. Modify the functions for
registering a region to take an additional owner module parameter and
rename them to avoid conflicts. Use the old function names for helper
macros that automatically set the module that registers the region as the
owner. This ensures compatibility with existing low-level control modules
and reduces the chances of registering a region without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga region.
Fixes: 0fa20cdfcc1f ("fpga: fpga-region: device tree control for FPGA")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Russ Weight <russ.weight@linux.dev>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240419083601.77403-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8886a579744fbfa53e69aa453ed10ae3b1f9abac ]
The FPGA region class driver data structure is being treated as a
managed resource instead of using the standard dev_release call-back
function to release the class data structure. This change removes the
managed resource code and combines the create() and register()
functions into a single register() or register_full() function.
The register_full() function accepts an info data structure to provide
flexibility in passing optional parameters. The register() function
supports the current parameter list for users that don't require the
use of optional parameters.
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Stable-dep-of: b7c0e1ecee40 ("fpga: region: add owner module and take its refcount")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 011c49e3703854e52c0fb88f22cf38aca1d4d514 ]
Change use of 'a fpga' to 'an fpga'
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210608212350.3029742-10-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b7c0e1ecee40 ("fpga: region: add owner module and take its refcount")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dd6b32e76ff714308964cd9ec91466a343dcb8b ]
The current implementation interprets negative values returned from
`dps310_calculate_temp` as error codes.
This has a side effect that when negative temperature values are
calculated, they are interpreted as error.
Fix this by using the return value only for error handling and passing a
pointer for the value.
Fixes: ba6ec48e76bc ("iio: Add driver for Infineon DPS310")
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Link: https://lore.kernel.org/r/20240415105030.1161770-2-thomas.haemmerle@leica-geosystems.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a8e4ab0c93fad30769479f86849e22d63cd0e12 ]
Replace incorrect include with the proper one for sched_set_fifo()
declaration.
Fixes: 28d2f209cd16 ("sched,serial: Convert to sched_set_fifo()")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a0b8c0da8d8d418cde6894a104cf74e6098ddfa ]
The arche-ctrl has two platform drivers and three of_device_id tables,
but one table is only used for the the module loader, while the other
two seem to be associated with their drivers.
This leads to a W=1 warning when the driver is built-in:
drivers/staging/greybus/arche-platform.c:623:34: error: 'arche_combined_id' defined but not used [-Werror=unused-const-variable=]
623 | static const struct of_device_id arche_combined_id[] = {
Drop the extra table and register both tables that are actually
used as the ones for the module loader instead.
Fixes: 7b62b61c752a ("greybus: arche-ctrl: Don't expose driver internals to arche-platform driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-18-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e60955dbecb97f080848a57524827e2db29c70fd ]
Sparse is not happy about misuse of bitwise types:
.../max3100.c:194:13: warning: incorrect type in assignment (different base types)
.../max3100.c:194:13: expected unsigned short [addressable] [usertype] etx
.../max3100.c:194:13: got restricted __be16 [usertype]
.../max3100.c:202:15: warning: cast to restricted __be16
Fix this by choosing proper types for the respective variables.
Fixes: 7831d56b0a35 ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 712a1fcb38dc7cac6da63ee79a88708fbf9c45ec ]
The removal of the last MAX3100 device triggers the removal of
the driver. However, code doesn't update the respective global
variable and after insmod — rmmod — insmod cycle the kernel
oopses:
max3100 spi-PRP0001:01: max3100_probe: adding port 0
BUG: kernel NULL pointer dereference, address: 0000000000000408
...
RIP: 0010:serial_core_register_port+0xa0/0x840
...
max3100_probe+0x1b6/0x280 [max3100]
spi_probe+0x8d/0xb0
Update the actual state so next time UART driver will be registered
again.
Hugo also noticed, that the error path in the probe also affected
by having the variable set, and not cleared. Instead of clearing it
move the assignment after the successfull uart_register_driver() call.
Fixes: 7831d56b0a35 ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240402195306.269276-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77ab53371a2066fdf9b895246505f5ef5a4b5d47 ]
uart_handle_cts_change() has to be called with port lock taken,
Since we run it in a separate work, the lock may not be taken at
the time of running. Make sure that it's taken by explicitly doing
that. Without it we got a splat:
WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0
...
Workqueue: max3100-0 max3100_work [max3100]
RIP: 0010:uart_handle_cts_change+0xa6/0xb0
...
max3100_handlerx+0xc5/0x110 [max3100]
max3100_work+0x12a/0x340 [max3100]
Fixes: 7831d56b0a35 ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf770af5645a41a753c55a053fa1237105b0964a ]
dmi_class uses kfree() as the .release function, but that now causes
a warning with clang-16 as it violates control flow integrity (KCFI)
rules:
drivers/firmware/dmi-id.c:174:17: error: cast from 'void (*)(const void *)' to 'void (*)(struct device *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
174 | .dev_release = (void(*)(struct device *)) kfree,
Add an explicit function to call kfree() instead.
Fixes: 4f5c791a850e ("DMI-based module autoloading")
Link: https://lore.kernel.org/lkml/20240213100238.456912-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b1c1cf08a0addb6df42f16b37133dc7a351de29 ]
As the possible failure of the dma_set_max_seg_size(), it should be
better to check the return value of the dma_set_max_seg_size().
Fixes: e3fdb1894cfa ("dmaengine: idma64: set maximum allowed segment size for DMA")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240403024932.3342606-1-nichen@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ee1b439b1540ae543149b15a2a61b9dff937d91 ]
For some reason, we add an offset to the PDI, presumably to skip the
PDI0 and PDI1 which are reserved for BPT.
This code is however completely wrong and leads to an out-of-bounds
access. We were just lucky so far since we used only a couple of PDIs
and remained within the PDI array bounds.
A Fixes: tag is not provided since there are no known platforms where
the out-of-bounds would be accessed, and the initial code had problems
as well.
A follow-up patch completely removes this useless offset.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326090122.1051806-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1ba19a1ae7cd1e324685ded4ab563e78fe68648 ]
If channel for the given node is not found we return null from
get_channel_from_mode. Make sure we validate the return pointer
before using it in two of the missing places.
This was originally reported in [0]:
Found by Linux Verification Center (linuxtesting.org) with SVACE.
[0] https://lore.kernel.org/all/20240301190425.120605-1-m.lobanov@rosalinux.ru
Fixes: 2870b52bae4c ("greybus: lights: add lights implementation")
Reported-by: Mikhail Lobanov <m.lobanov@rosalinux.ru>
Suggested-by: Mikhail Lobanov <m.lobanov@rosalinux.ru>
Suggested-by: Alex Elder <elder@ieee.org>
Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
Link: https://lore.kernel.org/r/20240325221549.2185265-1-rmfrfs@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49ca2b2ef3d003402584c68ae7b3055ba72e750a ]
Truncate the device name to store IPoIB VLAN name.
[leonro@5b4e8fba4ddd kernel]$ make -s -j 20 allmodconfig
[leonro@5b4e8fba4ddd kernel]$ make -s -j 20 W=1 drivers/infiniband/ulp/ipoib/
drivers/infiniband/ulp/ipoib/ipoib_vlan.c: In function ‘ipoib_vlan_add’:
drivers/infiniband/ulp/ipoib/ipoib_vlan.c:187:52: error: ‘%04x’
directive output may be truncated writing 4 bytes into a region of size
between 0 and 15 [-Werror=format-truncation=]
187 | snprintf(intf_name, sizeof(intf_name), "%s.%04x",
| ^~~~
drivers/infiniband/ulp/ipoib/ipoib_vlan.c:187:48: note: directive
argument in the range [0, 65535]
187 | snprintf(intf_name, sizeof(intf_name), "%s.%04x",
| ^~~~~~~~~
drivers/infiniband/ulp/ipoib/ipoib_vlan.c:187:9: note: ‘snprintf’ output
between 6 and 21 bytes into a destination of size 16
187 | snprintf(intf_name, sizeof(intf_name), "%s.%04x",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
188 | ppriv->dev->name, pkey);
| ~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:244: drivers/infiniband/ulp/ipoib/ipoib_vlan.o] Error 1
make[6]: *** Waiting for unfinished jobs....
Fixes: 9baa0b036410 ("IB/ipoib: Add rtnl_link_ops support")
Link: https://lore.kernel.org/r/e9d3e1fef69df4c9beaf402cc3ac342bad680791.1715240029.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 349e859952285ab9689779fb46de163f13f18f43 ]
Too much print may lead to a panic in kernel. Change ibdev_err() to
ibdev_err_ratelimited(), and change the printing level of cqe dump
to debug level.
Fixes: 7c044adca272 ("RDMA/hns: Simplify the cqe code of poll cq")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240412091616.370789-11-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4125269bb9b22e1d8cdf4412c81be8074dbc61ca ]
Use complete parentheses to ensure that macro expansion does
not produce unexpected results.
Fixes: a25d13cbe816 ("RDMA/hns: Add the interfaces to support multi hop addressing for the contexts in hip08")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240412091616.370789-10-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 203b70fda63425a4eb29f03f9074859afe821a39 ]
As described in the ib_map_mr_sg function comment, it returns the number
of sg elements that were mapped to the memory region. However,
hns_roce_map_mr_sg returns the number of pages required for mapping the
DMA area. Fix it.
Fixes: 9b2cf76c9f05 ("RDMA/hns: Optimize PBL buffer allocation process")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20240411033851.2884771-1-shaozhengchao@huawei.com
Reviewed-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcdc366acf8ffc29f091a09e08b4e46caa0a0f21 ]
Types of some fields, variables and parameters of some functions should be
unsigned.
Link: https://lore.kernel.org/r/1607650657-35992-10-git-send-email-liweihang@huawei.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: 203b70fda634 ("RDMA/hns: Fix return value in hns_roce_map_mr_sg")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71586dd2001087e89e344e2c7dcee6b4a53bb6de ]
In order to improve performance by balancing the load between different
banks of cache, the QPC cache is desigend to choose one of 8 banks
according to lower 3 bits of QPN. The hns driver needs to count the number
of QP on each bank and then assigns the QP being created to the bank with
the minimum load first.
Link: https://lore.kernel.org/r/1606220649-1465-1-git-send-email-liweihang@huawei.com
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: 203b70fda634 ("RDMA/hns: Fix return value in hns_roce_map_mr_sg")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f6e2dcbb82b9b2ea304fe32635789fedd4e9868 ]
Add a group of flags to control the 'struct hns_roce_buf' allocation
flow, this is used to support the caller running in atomic context.
Link: https://lore.kernel.org/r/1605347916-15964-1-git-send-email-liweihang@huawei.com
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: 203b70fda634 ("RDMA/hns: Fix return value in hns_roce_map_mr_sg")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de1c705c50326acaceaf1f02bc5bf6f267c572bd ]
The functions mipi_dsi_compression_mode() and
mipi_dsi_picture_parameter_set() return 0-or-error rather than a buffer
size. Follow example of other similar MIPI DSI functions and use int
return type instead of size_t.
Fixes: f4dea1aaa9a1 ("drm/dsi: add helpers for DSI compression mode and PPS packets")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240408-lg-sw43408-panel-v5-2-4e092da22991@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11ac72d033b9f577e8ba0c7a41d1c312bb232593 ]
The .bpc = 6 implies .bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ,
add the missing bus_format. Add missing connector type and bus_flags
as well.
Documentation [1] 1.4 GENERAL SPECIFICATI0NS indicates this panel is
capable of both RGB 18bit/24bit panel, the current configuration uses
18bit mode, .bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG , .bpc = 6.
Support for the 24bit mode would require another entry in panel-simple
with .bus_format = MEDIA_BUS_FMT_RGB666_1X7X4_SPWG and .bpc = 8, which
is out of scope of this fix.
[1] https://www.distec.de/fileadmin/pdf/produkte/TFT-Displays/Innolux/G121X1-L03_Datasheet.pdf
Fixes: f8fa17ba812b ("drm/panel: simple: Add support for Innolux G121X1-L03")
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240328102746.17868-2-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 272377aa0e3dddeec3f568c8bb9d12c7a79d8ef5 ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: b26975593b17 ("display/drm/bridge: TC358775 DSI/LVDS driver")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-6-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd0a2c6a081ff67007323725b9ff07d9934b1ed8 ]
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-4-619a28148e5c@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c534b63bede6cb987c2946ed4d0b0013a52c5ba7 ]
In vc4_hdmi_audio_init() of_get_address() may return
NULL which is later dereferenced. Fix this bug by adding NULL check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: bb7d78568814 ("drm/vc4: Add HDMI audio support")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240409075622.11783-1-amishin@t-argos.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1f95aede6285dba6dd036d907196f35ae3a11ea ]
In malidp_mw_connector_reset, new memory is allocated with kzalloc, but
no check is performed. In order to prevent null pointer dereferencing,
ensure that mw_state is checked before calling
__drm_atomic_helper_connector_reset.
Fixes: 8cbc5caf36ef ("drm: mali-dp: Add writeback connector")
Signed-off-by: Huai-Yuan Liu <qq810974084@gmail.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240407063053.5481-1-qq810974084@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b621e9e9e148c0928ab109ac3d4b81487469acb ]
The allocation failure of mycs->yuv_scaler_binary in load_video_binaries()
is followed with a dereference of mycs->yuv_scaler_binary after the
following call chain:
sh_css_pipe_load_binaries()
|-> load_video_binaries(mycs->yuv_scaler_binary == NULL)
|
|-> sh_css_pipe_unload_binaries()
|-> unload_video_binaries()
In unload_video_binaries(), it calls to ia_css_binary_unload with argument
&pipe->pipe_settings.video.yuv_scaler_binary[i], which refers to the
same memory slot as mycs->yuv_scaler_binary. Thus, a null-pointer
dereference is triggered.
Link: https://lore.kernel.org/r/20240118151303.3828292-1-alexious@zju.edu.cn
Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51084f89d687e14d96278241e5200cde4b0985c7 ]
There is no reason to prohibit sh7760fb from being built as a
loadable module as suggested by Geert, so change the config symbol
from bool to tristate to allow that and change the FB dependency as
needed.
Fixes: f75f71b2c418 ("fbdev/sh7760fb: Depend on FB=y")
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 935a92a1c400285545198ca2800a4c6c519c650a ]
In cdns_mhdp_atomic_enable(), the return value of drm_mode_duplicate() is
assigned to mhdp_state->current_mode, and there is a dereference of it in
drm_mode_set_name(), which will lead to a NULL pointer dereference on
failure of drm_mode_duplicate().
Fix this bug add a check of mhdp_state->current_mode.
Fixes: fb43aa0acdfd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240408125810.21899-1-amishin@t-argos.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1820e16a3019b6258e6009d34432946a6ddd0a90 ]
Increase the size of led_names so it can fit any valid v4l2 device name.
Fixes:
drivers/media/radio/radio-shark2.c:197:17: warning: ‘%s’ directive output may be truncated writing up to 35 bytes into a region of size 32 [-Wformat-truncation=]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bb1fd7eddcab2d28cfc11eb20f1029154dac718 ]
The return value of dvb_ca_en50221_init() is not checked here that may
cause undefined behavior in case of nonzero value return.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 25aee3debe04 ("[media] Rename media/dvb as media/pci")
Signed-off-by: Aleksandr Burakov <a.burakov@rosalinux.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 688cf598665851b9e8cb5083ff1d208ce43d10ff ]
Building with W=1 shows that a couple of variables in this driver are only
used in certain configurations:
drivers/video/fbdev/sis/init301.c:239:28: error: 'SiS_Part2CLVX_6' defined but not used [-Werror=unused-const-variable=]
239 | static const unsigned char SiS_Part2CLVX_6[] = { /* 1080i */
| ^~~~~~~~~~~~~~~
drivers/video/fbdev/sis/init301.c:230:28: error: 'SiS_Part2CLVX_5' defined but not used [-Werror=unused-const-variable=]
230 | static const unsigned char SiS_Part2CLVX_5[] = { /* 750p */
| ^~~~~~~~~~~~~~~
drivers/video/fbdev/sis/init301.c:211:28: error: 'SiS_Part2CLVX_4' defined but not used [-Werror=unused-const-variable=]
211 | static const unsigned char SiS_Part2CLVX_4[] = { /* PAL */
| ^~~~~~~~~~~~~~~
drivers/video/fbdev/sis/init301.c:192:28: error: 'SiS_Part2CLVX_3' defined but not used [-Werror=unused-const-variable=]
192 | static const unsigned char SiS_Part2CLVX_3[] = { /* NTSC, 525i, 525p */
| ^~~~~~~~~~~~~~~
drivers/video/fbdev/sis/init301.c:184:28: error: 'SiS_Part2CLVX_2' defined but not used [-Werror=unused-const-variable=]
184 | static const unsigned char SiS_Part2CLVX_2[] = {
| ^~~~~~~~~~~~~~~
drivers/video/fbdev/sis/init301.c:176:28: error: 'SiS_Part2CLVX_1' defined but not used [-Werror=unused-const-variable=]
176 | static const unsigned char SiS_Part2CLVX_1[] = {
| ^~~~~~~~~~~~~~~
This started showing up after the definitions were moved into the
source file from the header, which was not flagged by the compiler.
Move the definition into the appropriate #ifdef block that already
exists next to them.
Fixes: 5908986ef348 ("video: fbdev: sis: avoid mismatched prototypes")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e4350095e8ab2577ee05f8c3b044e661b5af9a0 ]
Add a check to mtk_drm_gem_init if we attempt to allocate a GEM object
of 0 bytes. Currently, no such check exists and the kernel will panic if
a userspace application attempts to allocate a 0x0 GBM buffer.
Tested by attempting to allocate a 0x0 GBM buffer on an MT8188 and
verifying that we now return EINVAL.
Fixes: 119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Justin Green <greenjustin@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240307180051.4104425-1-greenjustin@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfbc68e4d8695497f858a45a142665e22a512ea3 ]
Playing 4K media with 59.94 fractional rate (typically VP9) causes the screen to lose
sync with the following error reported in the system log:
[ 89.610280] Fatal Error, invalid HDMI vclk freq 593406
Modetest shows the following:
3840x2160 59.94 3840 4016 4104 4400 2160 2168 2178 2250 593407 flags: xxxx, xxxx,
drm calculated value -------------------------------------^
Change the fractional rate calculation to stop DIV_ROUND_CLOSEST rounding down which
results in vclk freq failing to match correctly.
Fixes: e5fab2ec9ca4 ("drm/meson: vclk: add support for YUV420 setup")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240109230704.4120561-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240109230704.4120561-1-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26c8cfb9d1e4b252336d23dd5127a8cbed414a32 ]
The name of the overlay does not fit into the fixed-length field:
drivers/video/fbdev/sh_mobile_lcdcfb.c:1577:2: error: 'snprintf' will always be truncated; specified size is 16, but format string expands to at least 25
Make it short enough by changing the string.
Fixes: c5deac3c9b22 ("fbdev: sh_mobile_lcdc: Implement overlays support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6819db94e1cd3ce24a432f3616cd563ed0c4eaba ]
The function hynix_nand_rr_init() should probably return an error code.
Judging by the usage, it seems that the return code is passed up
the call stack.
Right now, it always returns 0 and the function hynix_nand_cleanup()
in hynix_nand_init() has never been called.
Found by RASU JSC and Linux Verification Center (linuxtesting.org)
Fixes: 626994e07480 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs")
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240313102721.1991299-1-korotkov.maxim.s@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ae548f1054a0b71678d0349c7dc9628ddd42ca ]
Fixes index out of bounds issue in the color transformation function.
The issue could occur when the index 'i' exceeds the number of transfer
function points (TRANSFER_FUNC_POINTS).
The fix adds a check to ensure 'i' is within bounds before accessing the
transfer function points. If 'i' is out of bounds, an error message is
logged and the function returns false to indicate an error.
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:405 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.red' 1025 <= s32max
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:406 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.green' 1025 <= s32max
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:407 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.blue' 1025 <= s32max
Fixes: b629596072e5 ("drm/amd/display: Build unity lut for shaper")
Cc: Vitaly Prosyak <vitaly.prosyak@amd.com>
Cc: Charlene Liu <Charlene.Liu@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d50729f1d60bca822ef6d9c1a5fb28d486bd7593 ]
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
v3: also fix a sparse error ( https://lore.kernel.org/oe-kbuild-all/202405091310.KvncIecx-lkp@intel.com/ )
v2: leave the skb_trim() game because smsc95xx_rx_csum_offload()
needs the csum part. (Jakub)
While we are it, use get_unaligned() in smsc95xx_rx_csum_offload().
Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: UNGLinuxDriver@microchip.com
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509083313.2113832-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 812552808f7ff71133fc59768cdc253c5b8ca1bf ]
This fixes a probably long standing problem in the Cortina
Gemini ethernet driver: there are some paths in the code
where the IRQ registers are written without taking the proper
locks.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509-gemini-ethernet-locking-v1-1-afd00a528b95@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
