[ Upstream commit e8343410ddf08fc36a9b9cc7c51a4e53a262d4c6 ]
Sometimes the stream may be stopped due to XRUN events, in which case
the userspace can call snd_pcm_drop() and snd_pcm_prepare() to stop and
start the stream again.
In these cases, we must wait for the DMA channel to synchronize before
marking the stream as prepared for playback, as the DMA channel gets
stopped by drop() without any synchronization. Make sure the ALSA core
synchronizes the DMA channel by adding a sync_stop() hook.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240611-asoc_next-v3-1-fcfd84b12164@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 644eebdbbf1154c995d6319c133d7d5b898c5ed2 ]
Intel machine drivers are used by parent platform drivers based on
closed-source firmware (Atom/SST and catpt) and SOF-based ones.
In some cases for ACPI-based platforms, the behavior of machine
drivers needs to be modified depending on the parent type, typically
for card names and power management.
An initial solution based on passing a boolean flag as a platform
device parameter was tested earlier. Since it looked overkill, this
patch suggests instead a simple string comparison to identify an SOF
parent device/driver.
Suggested-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0cb3b7fd530b ("ASoC: Intel: Disable route checks for Skylake boards")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47f56e38a199bd45514b8e0142399cba4feeaf1a ]
Add members to struct snd_soc_card to store the PCI subsystem ID (SSID)
of the soundcard.
The PCI specification provides two registers to store a vendor-specific
SSID that can be read by drivers to uniquely identify a particular
"soundcard". This is defined in the PCI specification to distinguish
products that use the same silicon (and therefore have the same silicon
ID) so that product-specific differences can be applied.
PCI only defines 0xFFFF as an invalid value. 0x0000 is not defined as
invalid. So the usual pattern of zero-filling the struct and then
assuming a zero value unset will not work. A flag is included to
indicate when the SSID information has been filled in.
Unlike DMI information, which has a free-format entirely up to the vendor,
the PCI SSID has a strictly defined format and a registry of vendor IDs.
It is usual in Windows drivers that the SSID is used as the sole identifier
of the specific end-product and the Windows driver contains tables mapping
that to information about the hardware setup, rather than using ACPI
properties.
This SSID is important information for ASoC components that need to apply
hardware-specific configuration on PCI-based systems.
As the SSID is a generic part of the PCI specification and is treated as
identifying the "soundcard", it is reasonable to include this information
in struct snd_soc_card, instead of components inventing their own custom
ways to pass this information around.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230912163207.3498161-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
