commit e2006140ad2e01a02ed0aff49cc2ae3ceeb11f8d upstream.
I noticed that when we do discrete host router NVM upgrade and it gets
hot-removed from the PCIe side as a result of NVM firmware authentication,
if there is another host connected with enabled paths we hang in tearing
them down. This is due to fact that the Thunderbolt networking driver
also tries to cleanup the paths and ends up blocking in
tb_disconnect_xdomain_paths() waiting for the domain lock.
However, at this point we already cleaned the paths in tb_stop() so
there is really no need for tb_disconnect_xdomain_paths() to do that
anymore. Furthermore it already checks if the XDomain is unplugged and
bails out early so take advantage of that and mark the XDomain as
unplugged when we remove the parent router.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c38fa07dc69f0b9e6f43ecab96dc7861a70c827c upstream.
Currently we don't configure correctly the wake events after unplug of device
router. What can happen is that the downstream ports of host router will be
configured to wake on: USB4-wake and wake-on-disconnect, but not on
wake-on-connect. This may cause the later plugged device not to wake the
domain and fail in enumeration. Fix this by clearing downstream port's "USB4
Port is Configured" bit, after unplug of a device router.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd12acaf384c30437fa5a9a1f71df06fc9835fd upstream.
Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).
While there add the missing kernel-doc for tb_switch_resume().
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 582620d9f6b352552bc9a3316fe2b1c3acd8742d ]
On some systems the IOMMU blocks the first couple of driver ready
messages to the connection manager firmware as can be seen in below
excerpts:
thunderbolt 0000:06:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0010 address=0xbb0e3400 flags=0x0020]
or
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [04:00.0] PASID ffffffff fault addr 69974000 [fault reason 05] PTE Write access is not set
The reason is unknown and hard to debug because we were not able to
reproduce this locally. This only happens on certain systems with Intel
Maple Ridge Thunderbolt controller. If there is a device connected when
the driver is loaded the issue does not happen either. Only when there
is nothing connected (so typically when the system is booted up).
We can work this around by sending the driver ready several times. After
a couple of retries the message goes through and the controller works
just fine. For this reason make the number of retries a parameter for
icm_request() and then for Maple Ridge (and Titan Ridge as they us the
same function but this should not matter) increase number of retries
while shortening the timeout accordingly.
Reported-by: Werner Sembach <wse@tuxedocomputers.com>
Reported-by: Konrad J Hambrick <kjhambrick@gmail.com>
Reported-by: Calvin Walton <calvin.walton@kepstin.ca>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=214259
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a9fdf5f933a6f2b358fad0194b1287b67f6704b1 upstream.
Marek reported that when BlackMagic UltraStudio device is connected the
kernel repeatedly tries to enable lane bonding without success making
the device non-functional. It looks like the device does not have lane 1
connected at all so even though it is enabled we should not try to bond
the lanes. For this reason check that lane 1 is in fact CL0 (connected,
active) before attempting to bond the lanes.
Reported-by: Marek Šanta <teslan223@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217737
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>